FujiFilm CR-IR341 Service Manual page 148

C 1 2
ONTENTS
Fig. 2.7.3 Reading (2/3)
A
End-of-screen interrupt?
N
Y
From
the scanner
DELAY TZ14
board
FFM stop DRIVE (MZ1/OFF)
(Soft)
DELAY TZ15
After-reading conveyance grip
DRIVE (1/PE12)
Is SE1 closed?
Y
N
After-reading
Level 2 error
conveyance
After-reading conveyance
23DC
grip
grip operation error
After-reading conveyance
grip HP positioning
Fig. 2.7.4
Driving shaft grip release driving
DRIVE (MZ2/ON)
Driven shaft
Is SZ2 closed within TA24?
grip release
N
(fast)
Y
Driving shaft grip release stop
DRIVE (MZ2/OFF)
(Hard)
Releases should be
completed for both
of the parallel grips.
END
Table 2.7.3b Operation Parameters
Symbol Description
TD35 Normal reading IP trailing-edge detection timeout
TZ11 Subscanning IP leading-edge detection timeout
TZ13 Driven shaft grip release start
Wait for subscanning stop
TZ14
(conveyance compensation for logical reading)
009-051-04
05.31.99 FM2460
3 4 5 6
Level 0 error
0549
End-of-screen error
Side-positioning conveyance grip
DRIVE (MD2/PD22)
Is SD2 closed?
Y
N
Level 2 error
23BF
Side-positioning grip operation error
Side-positioning conveyance grip
HP positioning
Fig. 2.7.5
Driving shaft grip release stop
DRIVE (MZ2/OFF) (Soft)
Level 0 error
03C8
Driving shaft grip release error
Mode
—
—
—
Standard reading
18x38 portrait center
10x8 landscape upper right
10x12 portrait upper right
14x14 top
10x8 upper right
Pantomo portrait right center
CR-IR341 Service Manual
7 8 9 10
Table 2.7.3a Operation Parameters
Symbol
PD22 Conveyance grip
Conveyance grip
PE12
TZ12 Driving shaft grip start
TZ15 Wait for subscanning stop
Driving shaft grip timeout
TZ21
TZ22 Lower limit for driving shaft grip spec ( ST/HR)
TZ23 Upper limit for driving shaft grip spec ( ST/HR)
Driving shaft grip release timeout
TZ24
TZ31 Driven shaft grip timeout
TZ32 Upper limit for driven shaft grip spec ( ST/HR)
TZ33 Upper limit for driven shaft grip spec ( ST/HR)
Side-
positioning
conveyance
grip
FR1H0352.EPS
14x17 I 14x14 I 10x12 I
20.1 sec 16.0 sec 13.4 sec
21.1 sec 17.0 sec 14.4 sec
18.5 sec 14.5 sec 11.8 sec
0 sec 0 sec 0 sec
0 sec — —
0 sec 0 sec —
0 sec 0 sec —
0 sec — —
— — 0 sec
— — 0.5 sec
MD - 85
Description
(ST/HR)
(ST/HR)
(fast/HR)
(ST/HR)
8x10 I 18x24 ST 24x30 ST 18x24 HR
8.0 sec 6.8 sec 13.1 sec 11.5 sec
9.0 sec 7.8 sec 14.1 sec 12.5 sec
6.4 sec 5.2 sec 11.6 sec 10.4 sec
0 sec 0 sec 0 sec 0 sec
— — — —
— — — —
— — — —
— — — —
— — — —
— — — —
MD - 85
Value
144 p
-256 p
2.10/ 4.20 sec
0.3 sec
5 / 10 sec
1.6 / 3.3 sec
2.8 / 6.0 sec
2 sec
5 / 10s ec
1.2 / 3.0 sec
2.4 / 4.9 sec
TR1H0032.EPS
24x30 HR
17.8 sec
18.8 sec
16.8 sec
0 sec
—
—
—
—
—
—
TR1H0033.EPS