FujiFilm CR-IR341 Service Manual page 493

C 1 2
ONTENTS
1. Document Map
2. Common Procedures for Checks, Replacement,
and Adjustment MC - 4
2.1 Turning ON/OFF High-Voltage Switch
2.2 Checking Various Sensors
2.3 Clearing Backup Memory
2.4 Setting Date and Time
3. Removing and Reinstalling Covers MC - 20
4. Cassette Set Unit MC - 26
4.1 Pulling Out and Pushing In Tray of Cassette Set Unit
4.2 Removing and Reinstalling Cassette Set Unit
4.3 Removing and Reinstalling Shutter Assembly
4.4 Checking and Replacing Cassette Ejection Sensors (SA1, 5, 9, 13)
4.5 Checking, Replacing, and Adjusting Cassette IN Sensors
(SA2, 6, 10, 14)
4.6 Checking and Replacing Cassette Hold Sensors (SA3, 7, 11, 15)
4.7 Checking and Replacing Mammo/ST Sensors (SA4, 8, 12, 16)
4.8 Checking, Replacing, and Adjusting Cassette Hold Solenoids
(SOLA1-4)
4.9 Checking and Replacing Elevation HP Sensor (SA17)
4.10 Replacing Inch/Metric Guides
4.11 Adjusting Movable Roll
4.12 Replacing Rubber Rollers of Cassette Set Unit
4.13 Replacing Guide Plate of Cassette Set Unit
12. Erasure Conveyor MC - 218
12.1 Removing and Reinstalling Erasure Lamp Assembly
12.2 Removal and Reinstallation of Erasure Conveyor
12.3 Checking and Replacing After-Reading Conveyance
Standby IP Sensor (SF1)
12.4 Checking and Replacing Changeover IP Sensor (SF2)
12.5 Checking and Replacing Load Standby IP Sensor (SF3)
12.6 Checking and Replacing Overrun IP Sensor (SF4)
12.7 Replacing IP Transport Motor (MF1)
12.8 Replacing Erasure Lamp
12.9 Replacing Thermal Switches (TWS1, TWS2)
12.10 Replacing Erasure Cooling Fan (FANF1)
12.11 Replacing Erasure Cooling Fan Air Filter
12.12 Checking, Replacing, and Adjusting Erasure Unit
IP Conveyance Timing Belt
12.13 Replacing Erasure Conveyor Rubber Rollers
12.14 Checking and Replacing Branch Path Changeover
Guide
12.15 Checking and Replacing Shock Absorber
of Erasure Conveyor
11. After-Reading Conveyor MC - 208
11.1 Removing and Reinstalling After-Reading Conveyor
11.2 Checking and Replacing Grip Release HP Sensor (SE1)
11.3 Replacing Grip Release Motor (ME1)
11.4 Replacing IP Transport Motor (ME2)
11.5 Checking and Replacing Shock Absorber of
After-Reading Conveyor
10. Subscanning Unit MC - 162
10.1 Checking and Replacing SCN08A Board
10.2 Servicing Light-Collecting Guide
10.3 Checking and Replacing PMT08A Board
10.4 Servicing Light-Collecting Mirror
10.5 Checking and Replacing IP Leading-Edge Sensor
(SZ1/SED08A)
10.6 Checking and Replacing Driving-Side Grip Release HP Sensor
(SZ2)
10.7 Checking and Replacing Driven-Side Grip Release HP Sensor
(SZ3)
10.8 Checking and Replacing Subscanning Motor (MZ1)
10.9 Replacing Driving Shaft Grip Motor (MZ2)
10.10 Replacing Driven Shaft Grip Motor (MZ3)
10.11 Checking and Replacing SUS Belt/Rubber Belt/Tensioner
10.12 Checking and Replacing Kapton
10.13 Replacing Rubber Roller Located Above Subscanning Unit
10.14 Replacing Grip Arms
10.15 Replacing Guide Plate of Subscanning Unit
10.16 Replacing Lower Rubber Rollers of Subscanning Unit
10.17 Replacing and Adjusting Shock-Absorbing Rubbers
009-051-05
11.20.99 FM2638
3 4 5 6
¤
Belt/Tensioner/Flywheel
CR-IR341 Service Manual
7 8 9 10
5. Up-Down IP Removal Unit MC - 60
5.1 Checking and Replacing Suction Cup HP Sensor (SB1)
5.2 Checking and Replacing Cassette Inlet IP Sensor (SB2)
5.3 Checking, Replacing, and Adjusting Each Shelf Position
Sensor (SB3)
5.4 Checking and Adjusting Inch/Metric Sensor (SB4)
5.5 Checking and Replacing Suction Sensor (SB5)
5.6 Replacing Suction Pump (PB1)
5.7 Replacing IP Leak Valve (SVB1)
5.8 Replacing Suction Cups
5.9 Replacing Suction Cup Drive Motor (MB1)
5.10 Replacing IP Transport Motor (MB2)
5.11 Replacing Up-Down Drive Motor (MB3)
5.12 Replacing Elevation Timing Belt
5.13 Checking and Replacing Shock Absorbers of IP
Removal Unit
5.14 Checking and Replacing Elevation Changeover Guide
5.15 Replacing Vertical Conveyor Guide
6. Before-Side-Positioning Conveyor MC - 86
6.1 Removing and Reinstalling Before-Side-Positioning
Conveyor
6.2 Checking and Replacing Before-BCR IP Sensor (SC1)
6.3 Checking and Replacing Convergence Standby
IP Sensor (SC2)
6.4 Checking, Replacing, and Adjusting Convergence
Path Changeover Guide Drive Solenoid (SOLC1)
6.5 Replacing Before-Side-Positioning Conveyor
IP Transport Motor (MC1)
6.6 Replacing and Adjusting Before-Side-Positioning
Conveyor Drive Timing Belt
FRONT
6.7 Replacing Cleaning Roller
6.8 Replacing Before-Side-Positioning Conveyor
Rubber Rollers
6.9 Checking and Replacing Shock Absorber-Attached
Guide of Before-Side-Positioning Conveyor
7. Pulling Out and Pushing In Scanner Unit
MC - 106
8. Side-Positioning Conveyor MC - 110
8.1 Removing and Reinstalling Side-Positioning Conveyor
8.2 Checking and Replacing Side-Positioning Mechanism
HP Sensor (SD1)
8.3 Checking and Replacing Grip Release HP Sensor (SD2)
8.4 Checking and Replacing Side-Positioning IP Sensor (SD3)
8.5 Replacing Side-Positioning Motor (MD1)
8.6 Replacing Grip Release Motor (MD2)
8.7 Replacing IP Transport Motor (MD3)
8.8 Replacing Barcode Reader (BCR)
8.9 Checking and Replacing Side-Positioning Conveyor Grip
Mechanism
8.10 Checking and Replacing Side-Positioning Top Stopper
8.11 Replacing Side-Positioning Conveyor Grip Release
Timing Belt
8.12 Checking, Replacing, and Adjusting Side-Positioning
Conveyor IP Conveyance Timing Belt
8.13 Replacing Side-Positioning Conveyor Rubber Rollers
8.14 Checking and Replacing Shock Absorbers of
Side-Positioning Conveyor
9. Scanning Optics Unit MC - 132
9.1 Adjusting Read Start Position and Read Width
9.2 Shading/Sensitivity Correction
9.3 Removing and Reinstalling Scanning Optics Unit
9.4 Checking and Replacing LD Assembly
9.5 Checking and Replacing Polygonal Mirror Assembly
9.6 Checking and Replacing SYN08A Board
13. Housings MC - 252
13.1 Replacing Power Supply Unit
13.2 Replacing Fuses
13.3 Replacing HDD
13.4 Replacing FDD and Checking Boards Setting
13.5 Replacing the Monitor
13.6 Cleaning Monitor Screen
MC - 2
FR1H1319.EPS
MC - 2