Freescale Semiconductor PowerQUICC MPC885 Reference Manual page 764

SCC Ethernet Mode
27.7 SCC Ethernet Parameter RAM
For ethernet mode, the protocol-specific area of the SCC parameter RAM is mapped as in
1
Offset Name
0x30 C_PRES
0x34 C_MASK
0x38 CRCEC
0x3C ALEC
0x40 DISFC
0x44 PADS
0x46 RET_LIM
0x48 RET_CNT
0x4A MFLR
0x4C MINFLR
0x4E MAXD1
0x50 MAXD2
0x52 MAXD
0x54 DMA_CNT
27-8
Table 27-2. SCC Ethernet Parameter RAM Memory Map
Width
Word Preset CRC. For the 32-bit CRC-CCITT, initialize to 0xFFFFFFFF.
Word Constant mask for CRC. For the 32-bit CRC-CCITT, initialized to 0xDEBB20E3.
Word CRC error, alignment error, and discard frame counters. The CPM maintains
these 32-bit (modulo 2
disabled. CRCEC is incremented for each received frame with a CRC error, not
including frames not addressed to the controller, frames received in the
out-of-buffers condition, frames with overrun errors, or frames with alignment
errors. ALEC is incremented for frames received with dribbling bits, but does not
include frames not addressed to the controller, frames received in the
out-of-buffers condition, or frames with overrun errors. DISFC is incremented for
frames discarded because of the out-of-buffers condition or an overrun error. The
CRC does not have to be correct for DISFC to be incremented.
Hword Short frame PAD character. Write the pad character pattern to be sent when short
frame padding is implemented into PADS. The pattern may be of any value, but
both the high and low bytes should be the same.
Hword Retry limit. Number of retries (typically 15 decimal) that can be made to send a
frame. An interrupt can be generated if the limit is reached.
Hword Retry limit counter. Temporary down-counter for counting retries.
Hword Maximum frame length register (typically 1518 decimal). The ethernet controller
checks the length of an incoming ethernet frame against this limit. If it is
exceeded, the rest of the frame is discarded and LG is set in the last BD of that
frame. The controller reports frame status and length in the last BD. MFLR is
defined as all in-frame bytes between the start frame delimiter and the end of the
frame.
Hword Minimum frame length register. The ethernet controller checks the incoming
frame's length against MINFLR (typically 64 decimal). If the received frame is
smaller than MINFLR, it is discarded unless PSMR[RSH] is set, in which case, SH
is set in the last BD for the frame. For transmitting a frame that is too short, the
ethernet controller pads the frame to make it MINFLR bytes long, depending on
how PAD is set in the TxBD and on the PAD value in the parameter RAM.
Hword Max DMA n length. Gives the option to stop system bus writes after a frame
exceeds a certain size. However, this value is valid only if an address match is
Hword
found. The ethernet controller checks the length of an incoming ethernet frame
against this user-defined value (usually 1520 decimal). If this limit is exceeded,
the rest of the incoming frame is discarded. The ethernet controller waits until the
end of the frame or until MFLR bytes are received and reports the frame status
and the frame length in the last RxBD.
MAXD1 is used when an address matches an individual or group address.
MAXD2 is used in promiscuous mode when no address match is detected. In a
monitor station, MAXD2 can be much less than MAXD1 to receive entire frames
addressed to this station, but only the headers of the other frames are received.
Hword Rx max DMA.
Hword Rx DMA counter. A temporary down-counter used to track frame length.
MPC885 PowerQUICC Family Reference Manual, Rev. 2
Description
32
) counters that can be initialized while the channel is
Table 27-2.
Freescale Semiconductor