Advertisement
Quick Links
Freescale Semiconductor
MPC8572E Advanced Mezzanine Card
Hardware Getting Started Guide
About this Document
This document describes how to connect to the
MPC8572EAMC and verify its basic operation. Settings for
the switches and jumpers are shown, as well as instruction
for connecting peripheral devices. In addition, instructions
for connecting a debugger to the MPC8572EAMC, such as
Freescale's CodeWarrior are included, but instructions for
working with this debugger are beyond the scope of this
document.
Required Reading
It is assumed that the reader is familiar with the MPC8572E
microprocessor and MPC8572E PowerQUICC™ III
Integrated Host Processor Family Reference Manual as well
as the content of the High Level Design Document for
MPC8572EAMC.
© Freescale Semiconductor, Inc., 2008. All rights reserved.
Document Number: MPC8572EAMCGSG
Contents
1. Check Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Assemble and Connect the Board . . . . . . . . . . . . . . . . 6
5. Front Panel Connectivity . . . . . . . . . . . . . . . . . . . . . . 8
6. Module Management Support . . . . . . . . . . . . . . . . . . 9
7. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Rev. 1.0, 08/2008
Advertisement
Related Manuals for Freescale Semiconductor MPC8572E
Summary of Contents for Freescale Semiconductor MPC8572E
-
Page 1: Table Of Contents
Required Reading It is assumed that the reader is familiar with the MPC8572E microprocessor and MPC8572E PowerQUICC™ III Integrated Host Processor Family Reference Manual as well as the content of the High Level Design Document for MPC8572EAMC. - Page 2 Electrically erasable programmable read-only module GETH Gigabit Ethernet Hardware I2C (bus) Inter-IC bus Module management controller SRIO Serial RapidIO UART Universal asynchronous receive transmit Universal serial bus μTCA micro telecommunications computing architecture MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor...
-
Page 3: Check Switches
Reset/System CPLDs. Users should not attempt to reprogram the card using these headers because this may result in permanent card damage. The jumpers should remain in their default position as detailed in Table MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor... - Page 4 SW4.4 [SW4.4] = MMC H/W Select. ON—MMC present SW5.1 [SW5.1:2] = ON:OFF. CCB:SYSCLK = 10:1 (666 MHz) SW5.2 SW5.3 [SW5.3:4] = OFF:ON. e500 Core #0:CCB = 2:1 SW5.4 MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor...
- Page 5 Feature Status Comments Available IEEE Std 1588™ header Available USB DUART Connection. Provides debug information from MPC8572E Core #0 /1. — MMC BDM Debug header. Reserved for factory use only. Available COP Debug Header — CPLD JTAG Select. Reserved for factory use only.
-
Page 6: Assemble And Connect The Board
1. Switch on the power to the chassis. 2. Check for the blue front panel LED and power good LEDs being illuminated (a full description of the LED operation is given in Table MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor... - Page 7 Default on User debug #1 General debug system CPLD LD504 Yellow Default on User debug #2 General debug POR CPLD LD502 Green User config #1 User config #1 MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor...
-
Page 8: Connecting Jtag Debugging Tools To The Board
P1 provides a RJ45 10/100 Ethernet port. The final front panel connector P3 provides two high speed Gigabit Ethernet connections. Serial connectivity for MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor... -
Page 9: Module Management Support
Any board settings that users wish to make should be checked for validity against a recent version of the MPC8572E PowerQUICC™ III Integrated Host Processor Family Reference Manual. Operating the board, or MPC8572E device, beyond the recommended device operating conditions may cause permanent board damage. - Page 10 [OFF = 1, ON = 0) SW4.1 Reserved SW4.2 Reserved SW4.3 Reserved SW4.4 [SW4.4] = MMC H/W Select. ON—MMC present [SW4.4] = MMC H/W Select. OFF—MMC not present MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor...
- Page 11 [SW500.4:5] = ON:ON. MPC8572E acts as agent on all interfaces [SW500.4:5] = OFF:ON. MPC8572E acts as end point on PCIE #1 host SW500.5 [SW500.4:5] = ON:OFF. MPC8572E acts as end point on SRIO & PCIE #1 host [SW500.4:5] = OFF:OFF. MPC8572E acts as the host processor SW500.6 [SW500.6:8] = OFF:ON:ON.
-
Page 12: Revision History
Consult your local FAE for further information and card availability. Revision History Table 7 provides a revision history for this getting started guide. Table 7. Document Revision History Rev. Date Substantive Change(s) Number 08/2008 Initial public release. MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor... - Page 13 Revision History THIS PAGE INTENTIONALLY LEFT BLANK MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor...
- Page 14 Revision History THIS PAGE INTENTIONALLY LEFT BLANK MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor...
- Page 15 Revision History THIS PAGE INTENTIONALLY LEFT BLANK MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0 Freescale Semiconductor...
- Page 16 Headquarters surgical implant into the body, or other applications intended to support or sustain life, ARCO Tower 15F or for any other application in which the failure of the Freescale Semiconductor product 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064 could create a situation where personal injury or death may occur. Should Buyer...