LEGRAND Raritan PX3TS User Manual page 909

Send Sensor Report • 307, 396, 406, 422
Send Sensor Report Example • 406, 418, 419
Send SMS Message • 396, 408, 425
Send Snapshots via Email • 396, 409, 425
Sending Links to Snapshots or Videos • 494, 496,
498
Sensor Descriptors for Inlet Active Power • 440,
441
Sensor Log • 439, 440
Sensor RJ-45 Port Pinouts • 724
Sensor Threshold Configuration Commands • 669
Sensor Threshold Settings • 197, 216, 220, 226,
237, 251, 254, 263, 264, 274, 522, 834
Sensor/Actuator Location Example • 213, 275, 278
Sensor/Actuator States • 152, 186, 259, 260, 266,
267
Serial Port Configuration Commands • 693
Serial Port Settings • 552
Serial RS-232 • 723
Server Reachability Configuration Commands •
681
Server Reachability Information • 557
Server Reachability Information for a Specific
Server • 558
Server Status Checking or Power Control • 450
Setting an LED Color for a Rack Unit • 691, 692
Setting an LED Mode for a Rack Unit • 691, 692
Setting an Outlet's Cycling Power-Off Period • 631
Setting Data Logging • 309, 437, 439, 574
Setting Data Logging Measurements Per Entry •
574
Setting Default Measurement Units • 262, 296,
305, 306, 642, 644
Setting IPv4 Static Routes • 580
Setting IPv6 Static Routes • 584
Setting LAN Interface Parameters • 586
Setting LED Colors for Connected Tags • 689, 691,
692
Setting LED Colors for Disconnected Tags • 690,
691, 692
Setting Network Service Parameters • 595
Setting Non-Critical Outlets • 222, 227, 229
Setting NTP Parameters • 605, 608
Setting Outlet Power-On Sequence and Delay •
222, 226, 699, 701
Setting the Alarmed to Normal Delay for DX-PIR •
666
Setting the Automatic Daylight Savings Time • 607
Setting the Baud Rates • 694
Setting the BSSID • 593
Setting the Cascading Mode • 6, 16, 27, 28, 29, 31,
33, 157, 310, 311, 313, 317, 328, 330, 336, 468,
469
Setting the Date and Time • 309, 371, 403, 504,
523
Setting the HTTP Port • 596
Setting the HTTPS Port • 597
Setting the Inrush Guard Delay Time • 572
Setting the IPv4 Address • 579
Setting the IPv4 Configuration Mode • 577
Setting the IPv4 Gateway • 580
Setting the IPv4 Preferred Host Name • 578
Setting the IPv6 Address • 583
Setting the IPv6 Configuration Mode • 581
Setting the IPv6 Gateway • 584
Setting the IPv6 Preferred Host Name • 582
Setting the LED Operation Mode • 691
Setting the Maximum Number of Active Powered
Dry Contact Actuators • 576
Setting the Outlet Initialization Delay • 573
Setting the Outlet Power-On Sequence • 570
Setting the Outlet Power-On Sequence Delay •
571
Setting the Outlet Relay Behavior • 570
Setting the PDU-Defined Cycling Power-Off Period
• 572, 631
Setting the PDU-Defined Default Outlet State •
571, 630
Setting the Polling Interval • 686
Setting the PSK • 589
Setting the Registry to Permit Write Operations to
the Schema • 786
Setting the SNMP Configuration • 599
Setting the SNMP Read Community • 600
Setting the SNMP Write Community • 600
Setting the SSID • 589
Setting the sysContact Value • 600
Setting the sysLocation Value • 601
Setting the sysName Value • 601
Setting the Time Zone • 523, 606
Setting the Wireless Authentication Method • 589
Setting the X Coordinate • 664
Setting the Y Coordinate • 664
Setting the Z Coordinate • 575, 665
Setting the Z Coordinate Format for Environmental
Sensors • 575, 665, 680
Index
889