Lenze L-force HighLine C 8400 Series Reference Manual page 587

Error number
32 bits 16 bits 16 bits
hex
xx.0140.00013 0x280d 10253
xx.0135.00004 0x2304
xx.0145.00035 0x2d23 11555
xx.0145.00014 0x2d0e 11534
xx.0145.00024 0x2d18 11544
xx.0145.00033 0x2d21 11553
xx.0145.00034 0x2d22 11554
xx.0145.00025 0x2d19 11545
xx.0145.00026 0x2d1a 11546
xx.0145.00050 0x2d32 11570
xx.0145.00051 0x2d33 11571
xx.0145.00052 0x2d34 11572
xx.0400.00009 0x1a09
xx.0400.00016 0x1a10
xx.0400.00104 0x1a68
xx.0400.00105 0x1a69
xx.0123.00094 0x175e
xx.0123.00095 0x175f
xx.0123.00099 0x1763
xx.0123.00057 0x1739
xx.0123.00058 0x173a
xx.0123.00059 0x173b
xx.0123.00074 0x174a
xx.0123.00145 0x1791
xx.0123.00015 0x170f
xx.0123.00016 0x1710
xx.0123.00017 0x1711
xx.0119.00050 0x1332
xx.0123.00105 0x1769
xx.0123.00007 0x1707
xx.0123.00030 0x171e
xx.0123.00071 0x1747
xx.0123.00065 0x1741
xx.0123.00090 0x175a
xx.0123.00096 0x1760
xx.0123.00097 0x1761
xx.0123.00098 0x1762
xx.0123.00031 0x171f
xx.0119.00001 0x1301
xx.0119.00015 0x130f
xx.0119.00000 0x1300
xx.0123.00032 0x1720
xx.0123.00033 0x1721
xx.0123.00001 0x1701
xx.0123.00093 0x175d
xx.0123.00014 0x170e
xx.0144.00001 0x2c01 11265
xx.0144.00002 0x2c02 11266
xx.0144.00003 0x2c03 11267
xx.0144.00004 0x2c04 11268
xx.0144.00007 0x2c07 11271
Firmware ≤ 11.00 - DMS 6.0 EN - 10/2011
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
Error message
dec
Cl01: Module missing/incompatible
8964 CP04: CAN RPDO4
dF10: AutoTrip Reset
dF14: SW/HW invalid
dF18: BU RCOM error
dF21: BU Watchdog
dF22: CU watchdog
dF25: CU RCOM error
dF26: Appl. watchdog
dF50: Retain error
dF51: CuCcr error
dF52: BuCcr error
6665 dH09: EEPROM power section
6672 dH10: Fan failure
6760 dH68: Adjustment data error CU
6761 dH69: Adjustment data error BU
5982 FC01: Switching frequency reduction
5983 FC02: Maximum speed for Fchop
5987 FC03: Field controller limitation
5945 Id1: Motor data identification error
5946 Id3: CINH motor data identification
5947 Id4: Resistance identification error
5962 Id5: Pole position identification error
6033 LP1: Motor phase failure
5903 LU: DC bus undervoltage
5904 oC1: Power section - short circuit
5905 oC2: Power section - earth fault
4914 oC5: Ixt overload
5993 oC6: I2xt motor overload
5895 oC7: Motor overcurrent
5918 oC10: Maximum current reached
5959 oC11: Clamp operation active
5953 oC12: I2xt brake resistor overload
5978 oC13: Maximum current for Fch exceeded
5984 oC14: Direct-axis current controller limitation
5985 oC15: Cross current controller limitation
5986 oC16: Torque controller limitation
5919 oC17: Clamp sets pulse inhibit
4865 oH1: Heatsink overtemperature
4879 oH3: Motor temperature (X106) triggered
4864 oH4: Heatsink temp. > shutdown temp. -5°C
5920 oS1: Maximum speed limit reached
5921 oS2: Max. motor speed
5889 ot1: Max. torque reached
5981 ot2: Speed controller output limited
5902 OU: DC bus overvoltage
PS01: No memory module
PS02: Invalid par. set
PS03: Invalid device par. set
PS04: Invalid MCI par. set
PS07: Invalid memory module par. set
L
8400 HighLine C | Reference manual
Diagnostics & error management
Error messages of the operating system
Response can be set in
(Lenze setting)
No Reaction C01501/2
No Reaction C00593/4
Fault C00189
Fault -
Fault -
Fault -
Fault -
Fault -
No Reaction C00580/1
Fault -
Fault -
Fault -
Fault -
Warning C00566
Fault -
Fault -
No Reaction C00590
No Reaction C00588
No Reaction C00570/4
WarningLocked -
WarningLocked -
Warning -
Fault C00643/1
No Reaction C00597
Trouble C00600/1
Fault -
Fault -
Warning C00604
Warning C00606
Fault -
Fault -
Fault -
Fault -
Fault -
No Reaction C00570/1
No Reaction C00570/2
No Reaction C00570/3
No Reaction C00569/1
Fault -
Fault C00585
No Reaction C00582
No Reaction C00579
Fault -
No Reaction C00608
No Reaction C00567
Trouble -
Warning -
Fault -
Fault -
Fault -
Fault -
CAN Emergency
Error Code
0x7000
0x8100
0xF000
0x6100
0x6100
0x6100
0x6100
0x6200
0x6100
0x6100
0x6100
0x5530
0x5000
0x5530
0x5530
0x2000
0xF000
0xF000
0xF000
0xF000
0xF000
0x3000
0x3100
0x2000
0x2000
0x2000
0x2000
0x2000
0x2000
0xF000
0xF000
0xF000
0xF000
0xF000
0xF000
0xF000
0x4000
0x4000
0x4000
0x8400
0x8400
0x8300
0xF000
0x3100
0x6300
0x6300
0x6300
0x6300
0x6300
587