Table 29.2 Dc Characteristics (3) - Renesas H8S/2158 User Manual

Table 29.2 DC Characteristics (3)

= 2.7 V to 3.6 V *
Conditions: V
CC
V = AV
SS
Item
Analog power During A/D or
supply current D/A conversion
Waiting for A/D or
D/A conversion
Reference power During A/D conversion
supply current
During A/D or D/A
conversion
Waiting for A/D or
D/A conversion
Analog power supply voltage *
RAM standby voltage
Notes: 1. The flash memory must be programmed or erased within the conditions V
2. Do not leave the AVCC, AVref, and AVSS pins open even if the A/D converter or D/A converter is
not used.
Even if the A/D converter or D/A converter is not used, apply a value in the range from 2.0 V to 3.6
V to the AVCC and AVref pins by connection to the power supply (V
these two pins should be AV
3. Includes peripheral module inputs multiplexed on the pin.
4. Maximum voltage applied to port 6 is V
of V + 0.3 V or AV
CC
output voltage is applied to port 6.
5. P80/ExIRQ8/SCL0, P81/ExIRQ9/SDA0, P82/ExIRQ10/SCL1, and P83/ExIRQ11/SDA1 are NMOS
push-pull outputs.
An external pull-up resistor is necessary to provide high-level output from SCL0, SCL1, SDA0, and
SDA1 (ICE in ICCR is 1).
P80 to P83, P87, P84/SCK0, P85/SCK1, and P86/SCK2 (ICE in ICCR is 0) high levels are driven
by NMOS. An external pull-up resistor is necessary to provide high-level output from these pins
when they are used as an output.
6. Indicates values when ICE in ICCR is 0. Low level output when the bus drive function is selected is
rated separately.
7. Current consumption values are for V
unloaded and the on-chip pull-up MOSs in the off state.
8. The values are for V
*
1 2
, AV
CC
*
2
= 0 V
SS
Symbol Min
AI
CC
AI
ref
1
AV
CC
V
RAM
≤ AV
ref CC
+ 0.3 V when the CIN input is selected. If port 6 is in output mode, the
CC
IH
≤ V
< 2.7 V, V
RAM CC
Section 29 Electrical Characteristics
= 2.7 V to 3.6 V, AV
Typ Max
— 1.2 2.0
— 0.01 5.0
— 0.5 1.0
— 2.0 5.0
— 0.01 5.0
2.7 — 3.6
2.0 — 3.6
2.0 — —
.
+ 0.3 V when the CIN input is not selected, or the lower
CC
min = V – 0.2 V and V
CC
min = V – 0.2 V, and V
IH CC
Rev. 3.00 Jan 25, 2006 page 829 of 872
*
2
= 2.7 V to AV
ref CC
Unit Test Conditions
mA
= 2.0 V to 3.6 V *
µA AV
CC
mA
= 2.0 V to AVcc *
µA AV
ref
V Operating
Idle/not used
= 3.0 V to 3.6 V.
CC
). The relationship between
CC
max = 0.2 V with all output pins
IL
max = 0.2 V.
IL
REJ09B0286-0300
,
2
2