Table of Contents
Advertisement
Quick Links
To our customers,
st
On April 1
, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corporation took over all the business of both
companies. Therefore, although the old company name remains in this document, it is a valid
Renesas Electronics document. We appreciate your understanding.
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
Old Company Name in Catalogs and Other Documents
Renesas Electronics website:
http://www.renesas.com
st
April 1
, 2010
Renesas Electronics Corporation
Advertisement
Table of Contents
Related Manuals for Renesas H8S/2168
Summary of Contents for Renesas H8S/2168
- Page 1 On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.
- Page 2 Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific”...
- Page 3 H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator HS2168ECN61H User’s Manual Renesas Microcomputer Development Environment System H8S Family / H8S/2100 Series Rev.2.00 2003.12...
- Page 4 Thank you for purchasing this user system interface cable (HS2168ECN61H) for the Renesas’ original microcomputer H8S/2168 group. The HS2168ECN61H is a user system interface cable that connects an H8S/2168 group E6000 emulator (HS2168EPI61H; hereinafter referred to as the emulator) to the IC socket for a TFP-144...
-
Page 5: Table Of Contents
Section 1 Configuration...1 Section 2 Connection Procedures ...3 Connecting User System Interface Cable to Emulator Station ... 3 2.1.1 Connecting User System Interface Cable to Cable Body Connector... 4 2.1.2 Connecting EIO Board 2 to Emulator... 5 2.1.3 Removing EIO Board 2 from Emulator... 6 Connecting User System Interface Cable to User System ... -
Page 6: Section 1 Configuration
Use an NQPACK144SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-144 package IC socket on the user system. Figure 1 shows the configuration of the HS2168ECN61H user system interface cable for the TFP-144 package. To emulator station Screws (M2.6 x 6 mm) EIO board 2 Figure 1 HS2168ECN61H User System Interface Cable Section 1 Configuration... - Page 7 Table 1 lists the HS2168ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS2168ECN61H Components No. Component Cable body Cable head IC socket Socket cover Screws (M2.6 x 6 mm) Screws (M2.0 x 10 mm) Screws (M2.0 x 6 mm) CTS screws (M3 x 6 mm) Guide pins (φ...
-
Page 8: Section 2 Connection Procedures
Section 2 Connection Procedures Connecting User System Interface Cable to Emulator Station Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. -
Page 9: Connecting User System Interface Cable To Cable Body Connector
2.1.1 Connecting User System Interface Cable to Cable Body Connector After making sure the direction of the cable body connector is correct, firmly insert the cable body connector into the emulator station socket, and fasten the emulator station with two CTS screws ×... -
Page 10: Connecting Eio Board 2 To Emulator
2.1.2 Connecting EIO Board 2 to Emulator 1. Remove four screws at the side of the emulator station. 2. Pull up and remove the cover of the emulator casing. 3. Insert connector P5 of EIO board 2 into connector P5 in the emulator station. 4. -
Page 11: Removing Eio Board 2 From Emulator
2.1.3 Removing EIO Board 2 from Emulator 1. Remove four screws from the side of the emulator station. 2. Pull up and remove the cover of the emulator casing. × 3. Remove two screws (M2.6 6 mm) from EIO board 2. 4. -
Page 12: Connecting User System Interface Cable To User System
Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. -
Page 13: Soldering Ic Socket
Use the guide pins provided to determine where to install the IC socket, as shown in figure 4. Pin 1 4 projections to apply epoxy resin adhesive to Bottom view of IC socket 2.2.2 Soldering IC Socket After fastening, solder the IC socket for a TFP-144 package to the user system. Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets. -
Page 14: Inserting Cable Head
2.2.3 Inserting Cable Head Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a TFP-144 package on the user system with pin 1 on the user system interface cable head, and insert the user system interface cable head into the IC socket on the user system, as shown in figure 5. - Page 15 Fasten the user system interface cable head to the IC socket for a TFP-144 package on the user system with the four screws (M2.0 time, alternating between screws on opposing corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components.
-
Page 16: Fastening Cable Body
2.2.5 Fastening Cable Body Connect the cable body and EIO board 1 to the cable head. Cable body EIO board 1 User system Figure 6 Fastening Cable Body and EIO Board 1 When removing the cable body or EIO board 1, push the unfastening jigs. If the lower part of the cable body is pushed, EIO board 1 may be removed. -
Page 17: Recommended Dimensions For User System Mount Pad
Recommended Dimensions for User System Mount Pad Figure 7 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for a TFP-144 package (NQPACK144SE: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 7 are somewhat different from those of the actual chip's mount pad. -
Page 18: Dimensions For User System Interface Cable Head
Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 8. 25.0 20.5 66.0 Unit: mm ± Tolerance: 0.5 mm Figure 8 Dimensions for User System Interface Cable Head... -
Page 19: Resulting Dimensions After Connecting User System Interface Cable
Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 9. Cable head User system Figure 9 Resulting Dimensions after Connecting User System Interface Cable IC socket (NQPACK144SE manufactured by... -
Page 20: Section 3 Installing The Mcu On The User System
Section 3 Installing the MCU on the User System 1. Check the location of pin 1 before inserting. 2. Use a screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. - Page 21 Screws (M2.0 x 6 mm) Socket cover Pin 1 IC socket (NQPACK144SE manufactured by Tokyo Eletech Corporation) User system Figure 10 Installing MCU to User System...
-
Page 22: Section 4 User System Interface Circuit
Section 4 User System Interface Circuit The microcomputer (H8S/2168) is installed in this user system interface cable for emulating the LPC function. An interface circuit, as shown in figure 11, is provided for the user system interface signal of the H8S/2168. Figure 12 and table 2 show the settings of switches. - Page 23 Table 2 Settings of Switches Switch Number Pin 1 Side Port E7 Port E6 Port E5 Port E4 Port E3 Port E2 Port E1 Port E0 Port D5 SW10 Port D4 SW11 Port D3 SW12 Port D2 SW13 Port D1 SW14 Port D0 Pin 3 Side...
-
Page 24: Section 5 Verifying Operation
Section 5 Verifying Operation 1. When using the E6000 emulator for the H8S/2168 group, turn on the emulator according to the procedures described in the H8S/2168 Group E6000 Emulator User's Manual (HS2168EPI61HE). 2. Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins with the MEMORY_FILL command (emulator command). -
Page 25: Section 6 Notice
1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU. - Page 26 6. To prevent EMI noise, enclose the user system interface cable head in a case. The recommended material of the case is iron plated with nickel or resin plated with nickel inside. The case must be large enough to include the user system interface cable head, user system interface cable, and target system.
- Page 27 Renesas Technology Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor for the latest product information before purchasing a product listed herein.
- Page 28 Publication Date: Rev.1.00, August 25, 2003 Rev.2.00, December 25, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. ©2003 Renesas Technology Corp. All rights reserved. Printed in Japan.
- Page 29 H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator HS2168ECN61H User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan...