Delta AX Series Instruction Manual page 557

AX- Ser i es Mo t i o n Co n t r o l l er I n s t r u c t i o n s Ma n u a l
Error code
0x18A95 DML_R2R_CIG_UNSUPPORTED_PID_
ADAPTABILITY_REFERENCE_SOURC
E
0x18A96 DML_R2R_CIG_UNSUPPORTED_LINE
_SPEED_SOURCE
0x18AA6 DML_R2R_RD_TENSION_CTRL_UNSU
PPORTED
0x18AA7 DML_R2R_RD_COMMUNICATION_ER
ROR
0x18AA8 DML_R2R_RD_REUSED_ANALOG_IN
PUT_AVI
0x18AA9 DML_R2R_RD_REUSED_ANALOG_IN
PUT_ACI
0x18AAA DML_R2R_RD_EXE_NOT_ON_STATE
_POWER_OFF
0x18AAB DML_R2R_RD_UNSUPPORTED_ROLL
_DIAMETER_SOURCE
0x18AAC DML_R2R_RD_ROLL_DIAMETER_MA
X_IS_OVER_RANGE
0x18AAD DML_R2R_RD_ROLL_DIAMETER_MIN
_IS_OVER_RANGE
0x18AAE DML_R2R_RD_PULSE_PER_REVOLU
TION_IS_OVER_RANGE
0x18AAF DML_R2R_RD_ROUND_PER_LAYER_I
S_OVER_RANGE
0x18AB0 DML_R2R_RD_MATERIAL_THICKNES
S_IS_OVER_RANGE
0x18AB1 DML_R2R_RD_ROLL_DIAMETER_FILT
ER_TIME_IS_OVER_RANGE
0x18AC4 DML_R2R_RU_TENSION_CTRL_UNSU
PPORTED
0x18AC5 DML_R2R_RU_COMMUNICATION_ER
ROR
0x18AC6 DML_R2R_RU_RUN_BEFORE_CFIG
0x18AC7 DML_R2R_RU_EXE_NOT_ON_STATE
_STANDSTILL
0x18AC8 DML_R2R_RU_CURRENT_LINE_SPEE
D_IS_OVER_RANGE
0x18AC9 DML_R2R_RU_TENSION_COMMAND_
IS_OVER_RANGE
0x18ACA DML_R2R_RU_TENSION_COMMAND_
AT_0_SPEED_IS_OVER_RANGE
0x18ACB DML_R2R_RU_PID_GAIN_P_1ST_IS_
OVER_RANGE
0x18ACC DML_R2R_RU_PID_TIME_I_1ST_IS_O
VER_RANGE
0x18ACD DML_R2R_RU_PID_GAIN_P_2ND_IS_
OVER_RANGE
0x18ACE DML_R2R_RU_PID_TIME_I_2ND_IS_O
VER_RANGE
0x18ACF DML_R2R_RU_NOT_IN_STATE_CONT
INUOUS_MOTION
Description Contents
Adaptive PID reference source not
supported.
Line speed source not supported.
Tension control is not supported.
SDO communication error.
AVI analog input is reused.
ACI analog input is reused.
R2R_RollDiameter is not run in power
off state.
Roll diameter source not supported.
The maximum roll diameter is out of
range.
The minimum roll diameter is out of
range.
The number of pulses per revolution is
out of range.
The number of turns per layer is out of
range.
Coil thickness is out of range.
Roll diameter calculation filter time is out
of range.
Tension control is not supported.
SDO communication error.
R2R_Run runs before
R2R_Configuration completes.
R2R_Run is not run in standstill state.
Out of range.
Out of range.
Out of range.
Out of range.
Out of range.
Out of range.
Out of range.
R2R_Run is forced out of continuous
motion state.
Ap p en d i x A
Corrective Action
Adaptive PID reference source not
supported.
Line speed source not supported.
Tension control is not supported.
SDO communication error.
AVI analog input is reused.
ACI analog input is reused.
R2R_RollDiameter is not run in power off
state.
Roll diameter source not supported.
The maximum roll diameter is out of
range.
The minimum roll diameter is out of
range.
The number of pulses per revolution is
out of range.
The number of turns per layer is out of
range.
Coil thickness is out of range.
Roll diameter calculation filter time is out
of range.
Tension control is not supported.
SDO communication error.
R2R_Run runs before
R2R_Configuration completes.
R2R_Run is not run in standstill state.
Out of range.
Out of range.
Out of range.
Out of range.
Out of range.
Out of range.
Out of range.
R2R_Run is forced out of continuous
motion state.
5 5 2