Siemens SINAMICS G120D List Manual page 557

p2299[0...n]
p2513[0...3]
p2515[0...3]
p2516[0...3]
p2530
p2531
p2532
p2537
p2541
p2555
p2578
p2579
p2593
p2594[0...2]
p2598[0...3]
p2642
p2643
p2644
p2645
p2646
p2654
p2657
p2660
p3230[0...n]
p20094[0...3]
p20098[0...3]
p20102[0...1]
p20106[0...1]
p20110[0...3]
p20114[0...3]
p20118[0...1]
p20123[0...1]
p20128
p20133
p20218[0...1]
p20223[0...1]
p20228
p20236
p20244[0...1]
p20250[0...1]
p20256[0...1]
p20266
p20275
p20284
p20308[0...3]
p20312[0...1]
p20318[0...1]
p20372
p20378
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013
CI: Technology controller limit offset / Tech_ctrl lim offs
CI: LR Position actual value preprocessing corrective value / Act val_prep corr
CI: LR position actual setting setting value / s_act set setVal
CI: LR position offset / Position offset
CI: LR position setpoint / s_set
CI: LR velocity setpoint / v_set
CI: LR position actual value / s_act
CI: LR position controller adaptation / Adaptation
CI: LR position controller output speed limit signal source / LR_outp lim S_src
CI: LR LU/revolution LU/mm / LU/rev LU/mm
CI: EPOS software limit switch minus signal source / SW limSw Min S_src
CI: EPOS software limit switch plus signal source / SW limSwPlus S_src
CI: EPOS LU/revolution LU/mm / LU/rev LU/mm
CI: EPOS Maximum velocity externally limited / v_Max ext lim
CI: EPOS reference point coordinate signal source / Ref_pt coord S_src
CI: EPOS direct setpoint input/MDI position setpoint / MDI s_set
CI: EPOS direct setpoint input/MDI velocity setpoint / MDI v_set
CI: EPOS direct setpoint input/MDI acceleration override / MDI a_over
CI: EPOS direct setpoint input/MDI deceleration override / MDI -a_over
CI: EPOS velocity override / v_over
CI: EPOS direct setpoint input/MDI mode adaptation / MDI mode adapt
CI: EPOS position actual value/position setting value / Pos act/set value
CI: EPOS measured value referencing / Meas val ref
CI: Load monitoring speed actual value / Load monit n_act
CI: ADD 0 inputs / ADD 0 inputs
CI: ADD 1 inputs / ADD 1 inputs
CI: SUB 0 inputs / SUB 0 inputs
CI: SUB 1 inputs / SUB 1 inputs
CI: MUL 0 inputs / MUL 0 inputs
CI: MUL 1 inputs / MUL 1 inputs
CI: DIV 0 inputs / DIV 0 inputs
CI: DIV 1 inputs / DIV 1 inputs
CI: AVA 0 input X / AVA 0 input X
CI: AVA 1 input X / AVA 1 input X
CI: NSW 0 inputs / NSW 0 inputs
CI: NSW 1 inputs / NSW 1 inputs
CI: LIM 0 input X / LIM 0 input X
CI: LIM 1 input X / LIM 1 input X
CI: PT1 0 inputs / PT1 0 inputs
CI: PT1 1 inputs / PT1 1 inputs
CI: INT 0 inputs / INT 0 inputs
CI: LVM 0 input X / LVM 0 input X
CI: LVM 1 input X / LVM 1 input X
CI: DIF 0 input X / DIF 0 input X
CI: ADD 2 inputs / ADD 2 inputs
CI: NCM 0 inputs / NCM 0 inputs
CI: NCM 1 inputs / NCM 1 inputs
CI: PLI 0 input X / PLI 0 input X
CI: PLI 1 input X / PLI 1 input X
BICO parameters (connectors/binectors)
Parameters
1-557