Siemens SINAMICS G120D List Manual page 560

Parameters
BICO parameters (connectors/binectors)
1.4.4 Connector outputs (CO)
Product: SINAMICS G120D, Version: 4601800, Language: eng, Type: CO
r0021
r0025
r0026
r0027
r0032
r0034
r0035
r0036
r0037[0...19]
r0060
r0061[0...2]
r0062
r0063[0...2]
r0064
r0066
r0067
r0068[0...1]
r0069[0...6]
r0070
r0072
r0074
r0075
r0076
r0077
r0078
r0079
r0080[0...1]
r0081
r0082[0...2]
r0083
r0084[0...1]
r0087
r0094
r0289
r0479[0...2]
r0481[0...2]
r0482[0...2]
r0483[0...2]
r0497[0...2]
r0498[0...2]
r0499[0...2]
r0586
r0587
r0588
r0752[0...1]
r0755[0...1]
r0944
p1001[0...n]
p1002[0...n]
p1003[0...n]
1-560
CO: Actual speed smoothed / n_act smooth
CO: Output voltage smoothed / U_outp smooth
CO: DC link voltage smoothed / Vdc smooth
CO: Absolute actual current smoothed / I_act abs val smth
CO: Active power actual value smoothed / P_actv_act smth
CO: Motor utilization / Motor utilization
CO: Motor temperature / Mot temp
CO: Power unit overload I2t / PU overload I2t
CO: Power unit temperatures / PU temperatures
CO: Speed setpoint before the setpoint filter / n_set before filt.
CO: Actual speed unsmoothed / n_act unsmoothed
CO: Speed setpoint after the filter / n_set after filter
CO: Speed actual value / n_act
CO: Speed controller system deviation / n_ctrl system dev
CO: Output frequency / f_outp
CO: Output current maximum / I_outp max
CO: Absolute current actual value / I_act abs val
CO: Phase current actual value / I_phase act value
CO: Actual DC link voltage / Vdc act val
CO: Output voltage / U_output
CO: Modulat_depth / Modulat_depth
CO: Current setpoint field-generating / Id_set
CO: Current actual value field-generating / Id_act
CO: Current setpoint torque-generating / Iq_set
CO: Current actual value torque-generating / Iq_act
CO: Torque setpoint / M_set
CO: Torque actual value / M_act
CO: Torque utilization / M_Utilization
CO: Active power actual value / P_act
CO: Flux setpoint / Flex setp
CO: Flux actual value / Flux act val
CO: Actual power factor / Cos phi act
CO: Transformation angle / Transformat_angle
CO: Maximum power unit output current / PU I_outp max
CO: Diagnostics encoder position actual value Gn_XIST1 / Diag Gn_XIST1
CO: Encoder status word Gn_ZSW / Enc Gn_ZSW
CO: Encoder actual position value Gn_XIST1 / Enc Gn_XIST1
CO: Encoder actual position value Gn_XIST2 / Enc Gn_XIST2
CO: Encoder diagnostic signal double word / Enc diag DW
CO: Encoder diagnostic signal low word / Enc diag low word
CO: Encoder diagnostic signal high word / Enc diag high word
CO: Measuring probe speed actual value / MT n_act
CO: Measuring probe measuring time measured / MT t_meas measured
CO: Measuring probe pulse counter / MT pulse counter
CO: CO: CU analog inputs input voltage/current actual / CU AI U/I_inp act
CO: CO: CU analog inputs actual value in percent / CU AI value in %
CO: Counter for fault buffer changes / Fault buff change
CO: Fixed speed setpoint 1 / n_set_fixed 1
CO: Fixed speed setpoint 2 / n_set_fixed 2
CO: Fixed speed setpoint 3 / n_set_fixed 3
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013