Siemens SINAMICS G120D List Manual page 154

Parameters
List of parameters
p1051[0...n] CI: Speed limit RFG positive direction of rotation / n_limit RFG pos
CU240D-2_DP_F Access level: 3
CU240D-2_PN_F
Can be changed: T
CU250D-2_DP_F
Units group: -
CU250D-2_PN_F
Min
-
Description: Sets the signal source for the speed limit of the positive direction on the ramp-function generator input.
Note: The OFF3 ramp-down time (p1135) is effective when the limit is reduced.
p1051[0...n] CI: Speed limit RFG positive direction of rotation / n_limit RFG pos
CU240D-2_DP Access level: 3
CU240D-2_PN
Can be changed: T
Units group: -
Min
-
Description: Sets the signal source for the speed limit of the positive direction on the ramp-function generator input.
Note: The OFF3 ramp-down time (p1135) is effective when the limit is reduced.
p1052[0...n] CI: Speed limit RFG negative direction of rotation / n_limit RFG neg
CU240D-2_DP_F Access level: 3
CU240D-2_PN_F
Can be changed: T
CU250D-2_DP_F
Units group: -
CU250D-2_PN_F
Min
-
Description: Sets the signal source for the speed limit of the negative direction on the ramp-function generator input.
Note: The OFF3 ramp-down time (p1135) is effective when the limit is reduced.
p1052[0...n] CI: Speed limit RFG negative direction of rotation / n_limit RFG neg
CU240D-2_DP Access level: 3
CU240D-2_PN
Can be changed: T
Units group: -
Min
-
Description: Sets the signal source for the speed limit of the negative direction on the ramp-function generator input.
Note: The OFF3 ramp-down time (p1135) is effective when the limit is reduced.
p1055[0...n] BI: Jog bit 0 / Jog bit 0
CU240D-2_DP Access level: 3
CU240D-2_DP_F
Can be changed: T
CU240D-2_PN
Units group: -
CU240D-2_PN_F
Min
-
Description: Sets the signal source for jog 1.
Dependency: Refer to: p0840, p1058
1-154
Calculated: -
Scaling: p2000
Unit selection: -
Max
-
Calculated: -
Scaling: p2000
Unit selection: -
Max
-
Calculated: -
Scaling: p2000
Unit selection: -
Max
-
Calculated: -
Scaling: p2000
Unit selection: -
Max
-
Calculated: -
Scaling: -
Unit selection: -
Max
-
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013
Data type: U32 / FloatingPoint32
Dyn. index: CDS, p0170
Func. diagram: 3050
Factory setting
9733[0]
Data type: U32 / FloatingPoint32
Dyn. index: CDS, p0170
Func. diagram: 3050
Factory setting
1083[0]
Data type: U32 / FloatingPoint32
Dyn. index: CDS, p0170
Func. diagram: 3050
Factory setting
9733[1]
Data type: U32 / FloatingPoint32
Dyn. index: CDS, p0170
Func. diagram: 3050
Factory setting
1086[0]
Data type: U32 / Binary
Dyn. index: CDS, p0170
Func. diagram: 2501, 3030
Factory setting
[0] 0
[1] 722.0
[2] 0
[3] 0