Siemens SINAMICS G120D List Manual page 545

p1202[0...n]
p1203[0...n]
p1226[0...n]
p1300[0...n]
p1302[0...n]
p1310[0...n]
p1311[0...n]
p1312[0...n]
p1320[0...n]
p1321[0...n]
p1322[0...n]
p1323[0...n]
p1324[0...n]
p1325[0...n]
p1326[0...n]
p1327[0...n]
p1333[0...n]
p1334[0...n]
p1335[0...n]
p1336[0...n]
p1338[0...n]
p1339[0...n]
p1340[0...n]
p1341[0...n]
p1345[0...n]
p1346[0...n]
p1349[0...n]
p1350[0...n]
p1351[0...n]
p1400[0...n]
p1401[0...n]
p1402[0...n]
p1416[0...n]
p1441[0...n]
p1442[0...n]
p1452[0...n]
p1456[0...n]
p1457[0...n]
p1458[0...n]
p1459[0...n]
p1460[0...n]
p1461[0...n]
p1462[0...n]
p1463[0...n]
p1464[0...n]
p1465[0...n]
p1470[0...n]
p1472[0...n]
p1487[0...n]
p1488[0...n]
p1489[0...n]
p1496[0...n]
p1499[0...n]
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013
Flying restart search current / FlyRest I_srch
Flying restart search rate factor / FlyRst v_Srch Fact
Threshold for zero speed detection / n_standst n_thresh
Open-loop/closed-loop control operating mode / Op/cl-lp ctrl_mode
U/f control configuration / U/f config
Voltage boost permanent / U_boost perm
Voltage boost at acceleration / U_boost accelerate
Voltage boost when starting / U_boost starting
U/f control programmable characteristic frequency 1 / Uf char f1
U/f control programmable characteristic voltage 1 / Uf char U1
U/f control programmable characteristic frequency 2 / Uf char f2
U/f control programmable characteristic voltage 2 / Uf char U2
U/f control programmable characteristic frequency 3 / Uf char f3
U/f control programmable characteristic voltage 3 / Uf char U3
U/f control programmable characteristic frequency 4 / Uf char f4
U/f control programmable characteristic voltage 4 / Uf char U4
U/f control FCC starting frequency / U/f FCC f_start
U/f control slip compensation starting frequency / Slip comp start
Slip compensation scaling / Slip comp scal
Slip compensation limit value / Slip comp lim val
U/f mode resonance damping gain / Uf Res_damp gain
U/f mode resonance damping filter time constant / Uf Res_damp T
I_max frequency controller proportional gain / I_max_ctrl Kp
I_max frequency controller integral time / I_max_ctrl Tn
I_max voltage controller proportional gain / I_max_U_ctrl Kp
I_max voltage controller integral time / I_max_U_ctrl Tn
U/f mode resonance damping maximum frequency / Uf res_damp f_max
Soft starting / Soft starting
CO: Motor holding brake starting frequency / Brake f_start
Speed control configuration / n_ctrl config
Flux control configuration / Flux ctrl config
Closed-loop current control and motor model configuration / I_ctrl config
Speed setpoint filter 1 time constant / n_set_filt 1 T
Actual speed smoothing time / n_act T_smooth
Speed controller speed actual value smoothing time / n_ctr n_act T_smth
Speed controller speed actual value smoothing time (SLVC) / n_C n_act T_s SLVC
Speed controller P gain adaptation lower starting point / n_ctrl AdaptKpLow
Speed controller P gain adaptation upper starting point / n_ctrl AdaptKp up
Adaptation factor lower / Adapt_factor lower
Adaptation factor upper / Adapt_factor upper
Speed controller P gain adaptation speed lower / n_ctrl Kp n lower
Speed controller Kp adaptation speed upper scaling / n_ctr Kp n up scal
Speed controller integral time adaptation speed lower / n_ctrl Tn n lower
Speed controller Tn adaptation speed upper scaling / n_ctr Tn n up scal
Speed controller adaptation speed lower / n_ctrl n lower
Speed controller adaptation speed upper / n_ctrl n upper
Speed controller encoderless operation P-gain / n_ctrl SLVC Kp
Speed controller encoderless operation integral time / n_ctrl SLVC Tn
Droop compensation torque scaling / Droop M_comp scal
Droop input source / Droop input source
Droop feedback scaling / Droop scaling
Acceleration pre-control scaling / a_prectrl scal
Accelerating for torque control scaling / a for M_ctrl scal
Command and drive data sets - overview
Parameters
1-545