Siemens SINAMICS G120D List Manual page 546

Parameters
Command and drive data sets - overview
p1514[0...n]
p1517[0...n]
p1520[0...n]
p1521[0...n]
p1524[0...n]
p1525[0...n]
p1530[0...n]
p1531[0...n]
p1553[0...n]
p1570[0...n]
p1573[0...n]
p1574[0...n]
p1580[0...n]
p1582[0...n]
p1584[0...n]
p1594[0...n]
p1596[0...n]
p1610[0...n]
p1611[0...n]
p1616[0...n]
p1654[0...n]
p1702[0...n]
p1703[0...n]
p1715[0...n]
p1717[0...n]
p1726[0...n]
p1727[0...n]
p1730[0...n]
p1731[0...n]
p1740[0...n]
p1744[0...n]
p1745[0...n]
p1749[0...n]
p1750[0...n]
p1752[0...n]
p1753[0...n]
p1755[0...n]
p1758[0...n]
p1759[0...n]
p1760[0...n]
p1761[0...n]
p1764[0...n]
p1767[0...n]
p1774[0...n]
p1775[0...n]
p1780[0...n]
p1784[0...n]
p1785[0...n]
p1786[0...n]
r1787[0...n]
p1795[0...n]
r1797[0...n]
p1800[0...n]
1-546
Supplementary torque 2 scaling / M_suppl 2 scal
Accelerating torque smoothing time constant / M_accel T_smooth
CO: Torque limit upper / M_max upper
CO: Torque limit lower / M_max lower
CO: Torque limit upper/motoring scaling / M_max up/mot scal
CO: Torque limit lower scaling / M_max lower scal
Power limit motoring / P_max mot
Power limit regenerative / P_max gen
Stall limit scaling / Stall limit scal
CO: Flux setpoint / Flex setp
Flux threshold value magnetizing / Flux thresh magnet
Voltage reserve dynamic / U_reserve dyn
Efficiency optimization / Efficiency opt.
Flux setpoint smoothing time / Flux setp T_smth
Field weakening operation flux setpoint smoothing time / Field weak T_smth
Field-weakening controller P gain / Field_ctrl Kp
Field weakening controller integral-action time / Field_ctrl Tn
Torque setpoint static (SLVC) / M_set static
Supplementary accelerating torque (SLVC) / M_suppl_accel
Current setpoint smoothing time / I_set T_smooth
Curr. setpoint torque-gen. smoothing time field weakening range / Isq_s T_smth FW
Isd current controller pre-control scaling / Isd_ctr_prectrScal
Isq current controller pre-control scaling / Isq_ctr_prectrScal
Current controller P gain / I_ctrl Kp
Current controller integral-action time / I_ctrl Tn
Quadrature arm decoupling scaling / Transv_decpl scal
Quadrature arm decoupling at voltage limit scaling / TrnsvDecplVmaxScal
Isd controller integral component shutdown threshold / Isd_ctr I_compDeac
Isd controller combination current time component / Isd ctrl iCombi T1
Gain resonance damping for encoderless closed-loop control / Gain res_damp
Motor model speed threshold stall detection / MotMod n_thr stall
Motor model error threshold stall detection / MotMod ThreshStall
Motor model increase changeover speed encoderless operation / Incr n_chng no enc
Motor model configuration / MotMod config
Motor model changeover speed operation with encoder / MotMod n_chgov enc
Motor model changeover speed hysteresis operation with encoder / MotMod n_chgovHysE
Motor model changeover speed encoderless operation / MotMod n_chgSnsorl
Motor model changeover delay time closed/open-loop control / MotMod t cl_op
Motor model changeover delay time open/closed-loop control / MotMod t op_cl
Motor model with encoder speed adaptation Kp / MotMod wE n_ada Kp
Motor model with encoder speed adaptation Tn / MotMod wE n_ada Tn
Motor model without encoder speed adaptation Kp / MotMod woE n_adaKp
Motor model without encoder speed adaptation Tn / MotMod woE n_adaTn
Motor model offset voltage compensation alpha / MotMod offs comp A
Motor model offset voltage compensation beta / MotMod offs comp B
Motor model adaptation configuration / MotMod adapt conf
Motor model feedback scaling / MotMod fdbk scal
Motor model Lh adaptation Kp / MotMod Lh Kp
Motor model Lh adaptation integral time / MotMod Lh Tn
Motor model Lh adaptation corrective value / MotMod Lh corr
Motor model kT adaptation integral time / MotMod kT Tn
Motor model kT adaptation corrective value / MotMod kT corr
Pulse frequency setpoint / Pulse freq setp
© Siemens AG 2012 - 2013 All Rights Reserved
SINAMICS G120D List Manual (LH14), 01/2013