Select Lever Components; Select Lever Assembly Removal And Installation; Select Lever Knob Installation - Suzuki SX4 Service Manual
Hide thumbs
Also See for SX4:
- Owner's manual (47 pages) ,
- Owner's manual (18 pages) ,
- Owner's manual (16 pages)
Table of Contents
Advertisement
5A-86 Automatic Transmission/Transaxle:
5) Lower vehicle and pour proper amount of SUZUKI
ATF 3317 or Mobil ATF 3309.
6) Check fluid level referring to "A/T Fluid Level Check".
Automatic transaxle fluid
: SUZUKI ATF 3317 or Mobil ATF 3309
Automatic transaxle fluid capacity
When draining from drain plug hole: 2.6 liters
(5.49 / 4.58 US/Imp. pt.)
When overhauling: 5.8 liters (12.26 / 10.21 US/
Imp. pt.)
1
5
1. Fluid level gauge
2. "FULL HOT" mark
3. "LOW HOT" mark
Select Lever Components
4
1. Shift lock solenoid
2. Select lever assembly
4
3
2
1
I5RW0C510027-01
4. "FULL COLD" mark
5. "LOW COLD" mark
S7RW0A5106004
1
3
2
I5RW0C510028-04
3. Connector
4. "3" position switch
Select Lever Assembly Removal and
Installation
Remove and install select lever referring to "Select Lever
Components".
When installing select lever nothing the following.
• After installing select lever assembly, adjust select
cable referring to "Select Cable Adjustment".
Select Lever Knob Installation
Screw select lever knob onto select lever by specified
numbers of rotation below.
Rotation numbers for select lever knob installation
(a): 11 – 12 rotations
CAUTION
!
When installing select lever knob, do not turn
more than specified numbers of rotation.
Otherwise select lever knob is damaged.
S7RW0A5106005
S7RW0A5106006
1, (a)
I5RW0C510030-01
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated
My heater stopped working the blower **** is good, control unit ?
Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:
1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.
2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.
Checking and addressing these components should help identify and resolve the heater issue.
This answer is automatically generated