Diagnostic Information And Procedures; Air Bag Diagnostic System Check - Suzuki SX4 Service Manual
Hide thumbs
Also See for SX4:
- Owner's manual (47 pages) ,
- Owner's manual (18 pages) ,
- Owner's manual (278 pages)
Table of Contents
Advertisement
8B-11 Air Bag System:
A: Combination meter
B: Steering wheel
C: Seat
[D]: Hatchback model
[E]: Sedan model
1.
"AIR BAG" warning light
2. Driver air bag (inflator) module
3. Passenger air bag facing cover
4. Passenger air bag (inflator) module
Air Bag Diagnostic System Check
WARNING
!
To avoid deployment when troubleshooting
the air bag system, do not use electrical test
equipment such as a battery powered or AC
powered voltmeter, ohmmeter, etc., or any
type of electrical equipment other than that
specified in this manual. Do not use a non-
powered probe type tester.
Instructions in this manual must be followed
carefully, otherwise personal injury may
result.
CAUTION
!
• The order in which DTCs are diagnosed is
very important. Failure to diagnose the
DTCs in the order specified may result in
extended diagnostic time, incorrect
diagnosis and incorrect parts replacement.
• When measurement of resistance or
voltage is required in the flow, use a tester
along with a correct terminal adapter from
special tool (Connector test adapter kit).
• When a check for proper connection is
required, refer to "Inspection of
Intermittent and Poor Connections".
• If an open circuit in the air bag wire
harness damaged, connector or terminal is
found, replace the wire harness,
connectors and terminals as an assembly.
5. Side-air bag (inflator) module (8-channel system)
6. Side curtain-air bag (inflator) module (8-channel
system)
7. Contact coil assembly
8. Forward impact-sensor
9. Apron-side-member (driver side)
10. Side impact-sensor (8-channel system)
11. Side sill inner panel
12. SDM
13. Seat belt pretensioner
Diagnostic Information and Procedures
S7RW0A8204001
14.
"A/B" fuse in junction block assembly
15. Air bag harness in main harness
16. Air bag harness in instrument panel harness
17. Air bag harness in floor harness
18. Side-air bag harness (8-channel system)
19. Side curtain-air bag harness (8-channel
system)
20. Ground for air bag system
The diagnostic procedures used are designed to find
and repair air bag system malfunctions.
To get the best results, it is important to use the
diagnostic flow and follow the sequence in the following.
1) Perform the "Air Bag Diagnostic System Check
Flow".
(The "Air Bag Diagnostic System Check Flow" must
be the starting point of any air bag system diagnosis.
The "Air Bag Diagnostic System Check Flow" checks
for proper "AIR BAG" warning light operation through
"AIR BAG" warning light and whether air bag DTCs
exist.)
2) Refer to the proper diagnostic flow as directed by the
"Air Bag Diagnostic System Check Flow".
(The "Air Bag Diagnostic System Check Flow" will
lead you to the correct flow to diagnose any air bag
system malfunctions. Bypassing these procedures
may result in extended diagnostic time, incorrect
diagnosis and incorrect parts replacement.)
3) Repeat the "Air Bag Diagnostic System Check Flow"
after any repair or diagnostic procedures have been
performed.
(Performing the "Air Bag Diagnostic System Check
Flow" after all repair or diagnostic procedures will
ensure that the repair has been made correctly and
that no other malfunctions exist.)
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated
My heater stopped working the blower **** is good, control unit ?
Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:
1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.
2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.
Checking and addressing these components should help identify and resolve the heater issue.
This answer is automatically generated