Suzuki SX4 Service Manual page 805

1. Torque converter
2. Torque converter housing
: Apply sealant 99000-31230 to mating
surface to transaxle case.
3. Oil strainer assembly
: Replace oil strainer when overhauling.
4. Parking lock pawl shaft
5. Parking lock pawl
6. Parking lock pawl return spring
7. Parking lock pawl rod
8. Parking lock pawl bracket
9. Manual detent spring
10. Manual valve lever
11. Manual valve lever pin
12. Manual shift shaft
13. Manual shift shaft oil seal
: Apply grease 99000-25030 to oil seal
lip.
14. Differential side oil seal
: Apply grease 99000-25030 to oil seal
lip.
15. Torque converter housing plug
16. Lubrication LH tube
17. Lubrication RH tube
18. Fluid reservoir RH plate
19. Input shaft front thrust bearing
20. Input shaft rear thrust bearing
21. Input shaft rear thrust bearing race
22. Direct clutch hub
23. Lubrication tube clamp
24. Fluid reservoir LH plate
25. Governor apply No.2 gasket
26. Automatic transaxle case
27. Accumulator piston O-ring
28. Accumulator spring
29. C2 accumulator piston
30. C1 accumulator piston
31. B1 accumulator piston
32. Oil pan gasket
33. Oil pan
34. A/T fluid drain plug
35. Manual select lever
36. Lock washer
Automatic Transmission/Transaxle:
37. Transmission range sensor
38. Cooler check valve
39. Spring
40. Transaxle case plug
41. Fluid filler tube
42. Fluid level gauge
43. Fluid cooler inlet pipe
44. Fluid cooler outlet pipe
45. 2nd brake gasket
46. Brake drum gasket
47. Pipe union
48. Reduction drive gear nut
: After tightening nut so as rotational
torque of reduction drive gear to be in
specified value, caulk nut securely.
49. Reduction drive gear
50. Planetary ring gear subassembly
51. Breather hose
52. Breather union
53. Input shaft speed sensor
54. Valve body harness
55. 1st and reverse brake piston
56. O-ring
57. 1st and reverse brake return spring
subassembly
58. 1st and reverse brake disc
59. 1st and reverse brake separator plate
60. 1st and reverse brake retaining plate
61. 1st and reverse brake snap ring
62. Planetary gear assembly
63. Planetary carrier thrust washer
: Apply grease 99000-25030 to slide
contact face.
64. One-way clutch No.2 assembly
65. 2nd brake retaining plate
66. 2nd brake disc
67. 2nd brake separator plate
68. 2nd brake return spring subassembly
69. Front sun gear thrust bearing race
70. Front planetary sun gear
71. Planetary gear thrust bearing
72. One-way clutch No.1 assembly
5A-105
73. Rear planetary sun gear subassembly
74. Rear sun gear thrust bearing race
75. Rear sun gear thrust bearing
76. Forward clutch hub
77. Intermediate shaft thrust bearing race
78. Intermediate shaft thrust bearing
79. 2nd brake piston snap ring
80. O/D and 2nd coast brake retaining
plate snap ring
81. O/D and 2nd coast brake retaining
plate
82. O/D and 2nd coast brake disc
83. O/D and 2nd coast brake separator
plate
84. O/D and 2nd coast brake rear plate
85. Rear cover seal ring
86. Reverse clutch drum thrust bearing
87. Rear cover plug
88. Transaxle rear cover
: Apply sealant 99000-31230 to mating
surface.
89. Harness bracket
90. Select cable clamp
91. Governor apply No.1 gasket
92. Output shaft speed sensor (VSS)
93. One-way clutch outer race retainer
94. Select cable bracket
: Do not reuse.
: Apply automatic transaxle fluid.
: 5.5 N⋅m (0.55 kgf-m, 4.0 lb-ft)
: 7.0 N⋅m (0.7 kgf-m, 5.0 lb-ft)
: 7.5 N⋅m (0.75 kgf-m, 5.5 lb-ft)
: 10 N⋅m (1.0 kgf-m, 7.5 lb-ft)
: 13 N⋅m (1.3 kgf-m, 9.5 lb-ft)
: 17 N⋅m (1.7 kgf-m, 12.5 lb-ft)
: 35 N⋅m (3.5 kgf-m, 25.5 lb-ft)
: 23 N⋅m (2.3 kgf-m, 17.0 lb-ft)
: 25 N⋅m (2.5 kgf-m, 18.0 lb-ft)
: 33 N⋅m (3.3 kgf-m, 24.0 lb-ft)