Suzuki SX4 Service Manual page 1237
Hide thumbs
Also See for SX4:
- Owner's manual (47 pages) ,
- Owner's manual (16 pages) ,
- Owner's manual (18 pages)
Table of Contents
Advertisement
No.
Color
C124
BLU
C139
GRY
C141
BLK
C162
—
C165
BLK
C166
GRY
C192
—
C194
BLK
C195
BLK
C196
—
C282
—
C283
—
C343
N
A: Battery cable / C: Engine harness (M16A engine LHD)
C06
C07
C31
W/S
C194
C192
C91
C102
C42
C124
A
C32
C43
C162
Connective position
OCV
Shift solenoid
A/C compressor
Oil pressure switch
Back-up light switch
Transaxle range sensor
Generator
Generator
Starting motor
Starting motor
Main fuse box
Main fuse box
Main harness (To E371)
5
3
4
W/S
C195
C37
C141
C92
C196
C93
C47
C
C36
C48
C282
C123
C32
B
C283
C94
C101 C39
2
Wiring Systems:
Remarks
IF EQPD
A/T
M/T
A/T
A
Without OCV
With OCV
B
C34
C343
(TO E371)
C01
C122
C165
C139
C44
C166
1
A
I7RW0A910959-02
9A-14
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated
My heater stopped working the blower **** is good, control unit ?
Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:
1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.
2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.
Checking and addressing these components should help identify and resolve the heater issue.
This answer is automatically generated