Pressure Control Solenoid Valves Inspection - Suzuki SX4 Service Manual
Hide thumbs
Also See for SX4:
- Owner's manual (47 pages) ,
- Owner's manual (18 pages) ,
- Owner's manual (16 pages)
Table of Contents
Advertisement
5A-98 Automatic Transmission/Transaxle:
10) Remove valve body assembly referring to
"Automatic Transaxle Unit Disassembly".
11) Remove pressure control solenoid valve and TCC
pressure control solenoid valve referring to "Valve
Body Assembly Disassembly and Reassembly".
Installation
Reverse removal procedure to install pressure control
solenoid valve and valve body assembly noting the
following points.
• For detail of pressure control solenoid valve and TCC
pressure control solenoid valve installation, refer to
"Valve Body Assembly Disassembly and
Reassembly".
• For detail of valve body assembly installation, refer to
"Automatic Transaxle Unit Assembly".
• For detail of installing wire harness for solenoid valves
and sensor, refer to "Automatic Transaxle Unit
Assembly". Use new O-rings.
• For detail of A/T oil pan and oil strainer assembly
installation, refer to "Automatic Transaxle Unit
Assembly". Use new oil pan gasket.
• Pour A/T fluid and check fluid level according to
procedure described in "A/T Fluid Change".
• Check for fluid leakage after warming up A/T.
Pressure Control Solenoid Valves Inspection
CAUTION
!
• Be very careful as dust etc. does enter
when pressure control solenoid valves are
inspected.
Resistance Check
Measure resistance between pressure control solenoid
valves (Pressure control solenoid and TCC pressure
control solenoid) (1) terminals.
Pressure control solenoid valve and TCC pressure
control solenoid valve resistance
Standard: 5.0 – 5.6 Ω at 20 °C (68 °F)
S7RW0A5106025
1
I2RH01510071-01
Operation Check
Check pressure control solenoid valves (Pressure
control solenoid and TCC pressure control solenoid)
operation in the either manner of the following.
Using regulated DC power supply
1) Connect pressure control solenoid valve (1) with
regulated DC power supply (2) as shown in figure.
2) Turn regulated DC power supply switch ON and
increase voltage of power supply keeping current
within 1.0 A.
3) Check for gradual movement of valve (3) in the
direction of arrow "A" as voltage is increased.
4) Check movement of valve (3) in the direction of
arrow "B" as voltage is decreased.
5) Turn power supply switch OFF.
CAUTION
!
Do not pass current 1.0 A or more, or
pressure control solenoid is burned out.
I2RH0B510064-01
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated