Adding An Ipsg Card - Tekelec IP7 Secure Gateway Administration Manual

Database Administration Manual - IP7 Secure
Gateway
There are two different versions, RFC and Draft 6, of M2PA timer sets that can be assigned to IPSG
M2PA associations. Each version of the M2PA timer sets contains 20 timer sets. The values of these
timer sets can be changed with the
The version of the IPSG M2PA association and the M2PA timer set assigned to the association can
be changed with
association determines the version of the M2PA timer set that is assigned to the association. For
example, if M2PA timer set 3 is assigned to the IPSG M2PA association, and the association is an
RFC M2PA association, the RFC version of M2PA timer set 3 is used with the association. If M2PA
timer set 7 is assigned to the IPSG M2PA association, and the association is a Draft 6 M2PA
association, the Draft 6 version of M2PA timer set 7 is used with the association.
10. When an IPSG M3UA association is added to the database, UA parameter set 10 is assigned to the
association. There are 10 UA parameter sets that can be assigned to an association, but the UA
parameter set assignment can be changed, using the
procedure. The values assigned to each UA parameter set can be changed, except for UA parameter
set 10, using the
11. Configure the IPSG signaling links with either the
M3UA Signaling Link
number of signaling links the EAGLE 5 ISS is allowed to have, the
Controlled Feature
12. Configure the required routes - see Chapter 3, "SS7 Configuration," in the Database Administration
Manual - SS7.
13. An internal point code can be provisioned to provide routing to an IP end office node. Configure
the internal point codes by performing the
14. The network appearance field identifies the SS7 network context for the message, for the purpose
of logically separating the signaling traffic between the SGP (signaling gateway process) and the
application server over a common SCTP (stream control transmission protocol) association. This
field is contained in the DATA, DUNA, DAVA, DRST, DAUD, SCON, and DUPU messages.
Network appearances are configured by performing the
15. The EAGLE 5 ISS processes messages with a service information field (SIF) that is 272 bytes or
smaller. The Large MSU Support for IP Signaling feature allows the EAGLE 5 ISS to process messages
with a service indicator value of 6 to 15 and with a SIF that is larger than 272 bytes. Perform the
Activating the Large MSU Support for IP Signaling Feature
MSU Support for IP Signaling feature.

Adding an IPSG Card

This procedure is used to add an IPSG card to the database using the ent-card command. An IPSG
card is an E5-ENET card, part number 870-2212-xx, that is running the IPSG application.
The EAGLE 5 ISS can support a mixture of single-slot EDCMs and E5-ENET cards.
The ent-card command uses these parameters.
:loc – The location of the card being added to the database.
:type – The type of card being added to the database. For this procedure, the value of this parameter
is enet for en E5-ENET card and enet b for E5-ENET-B.
:appl – The application software that is assigned to the card. For this procedure, the value of this
parameter is ipsg.
910-6278-001 Revision A, January 2012
Changing an M2PA Timer Set
Changing the Attributes of an IPSG Association
Changing a UA Parameter Set
procedures. If the addition of these signaling links will exceed the current
procedure will have to be performed to increase the quantity of signaling links.
IPSG M2PA and M3UA Configuration Procedures
procedure.
procedure. The M2PA version of the
Changing the Attributes of an IPSG Association
procedure.
Adding an IPSG M2PA Linkset
Adding an End Node Internal Point
Adding a Network Appearance
procedure to enable and turn on the Large
or Adding an IPSG
Enabling the Large System # Links
Codeprocedure.
procedure.
644