Tekelec IP7 Secure Gateway Administration Manual page 772

Database Administration Manual - IP7 Secure
Gateway
To provision a EAGLE 5 ISS with more than 1200 signaling links, the EAGLE 5 ISS must have certain
levels of hardware installed. See the
Links section for more information on these hardware requirements.
The EAGLE 5 ISS can contain a mixture of low-speed, E1, T1, ATM high-speed, and IP signaling links.
Determining the Number of High-Speed and Low-Speed Signaling Links
The
determine the quantities of the different types of signaling links the EAGLE 5 ISS can have.
HC-MIM
E5-E1/T1
E5-ATM
E5-SM4G
E5-ENET
E5-based control cards
Single-Slot EDCM or E5-SLAN card for the STPLAN feature
Single-Slot EDCM or E5-STC card for the EAGLE 5 Integrated Monitoring Support feature
When the IPSG M3UA signaling link is added, the RSVDSLKTPS value that is assigned to the linkset
will be assigned to the signaling link. The sum of the TPS used by all the signaling links that are
assigned to the IPSG card cannot exceed 5000 TPS. The TPS used by the IPSG card and the TPS used
by each signaling link that is assigned to the IPSG card is shown by entering the rtrv-slk command
with the location of the IPSG card. If the 5000 TPS limit for the IPSG card will be exceeded by adding
the IPSG M3UA signaling link, one of these actions must be performed.
Another IPSG card must be used for the IPSG M3UA signaling link.
The RSVDSLKTPS values for the linksets shown in the rtrv-slk output for the IPSG card must
be reduced enough to allow the IPSG M3UA linkset to be added.
If adding the IPSG M3UA signaling link will exceed the maximum total provisioned system TPS, and
the maximum total provisioned system TPS is 500,000, perform the "Activating the HIPR2 High Rate
Mode" feature in the Database Administration Manual - System Management to enable and turn on the
HIPR2 High Rate Mode feature. When the HIPR2 High Rate Mode feature is enabled and turned on,
the maximum total provisioned system TPS is increased to 750,000. If the maximum total provisioned
system TPS is 750,000, or the maximum total provisioned system TPS is 500,000 and will not be
increased, and adding the IPSG M3UA signaling link will exceed the maximum total provisioned
system TPS, the IPSG M3UA signaling link cannot be added unless the amount of available TPS is
reduced enough to allow the IPSG M3UA signaling link to be added. The available TPS can be reduced
by performing one or more of these actions.
The IP TPS values of some IPGWx linksets have to be changed.
The MAXSLKTPS values of some IPSG linksets (and the RSVDSLKTPS values if necessary) have
to be changed.
Some ATM high-speed signaling links have to be removed.
An IPLIMx card that contains signaling links has to be removed.
Canceling the REPT-STAT-SLK, RTRV-LS, and RTRV-SLK Commands
Because the rept-stat-slk, rtrv-ls, and rtrv-slk commands used in this procedure can output
information for a long period of time, the rept-stat-slk, rtrv-ls, and rtrv-slk commands
can be canceled and the output to the terminal stopped. There are three ways that the rept-stat-slk,
rtrv-ls, and rtrv-slk commands can be canceled.
Press the F9 function key on the keyboard at the terminal where the rept-stat-slk, rtrv-ls,
or rtrv-slk commands were entered.
910-6278-001 Revision A, January 2012
IPSG M2PA and M3UA Configuration Procedures
Requirements for EAGLE 5 ISSs Containing more than 1200 Signaling
section describes how to
772