Figure 94: Configuring An Ip Link - Tekelec IP7 Secure Gateway Administration Manual

Database Administration Manual - IP7 Secure
Gateway
2103 A 192.1.1.22
2103 B --------------- --------------- HALF
2105 A 192.1.1.24
2105 B 192.1.1.54
2205 A 192.1.1.30
2205 B --------------- --------------- HALF
2207 A 192.1.1.32
2207 B --------------- --------------- HALF
2213 A 192.1.1.50
2213 B --------------- --------------- HALF
2301 A 192.1.1.52
2301 B --------------- --------------- HALF
IP-LNK table is (20 of 2048) 1% full.
If the required IP link, one that contains the desired IP address, is not shown in the rtrv-ip-lnk
output, add the IP link using the
assign the IP address of the IP link to the IP host name using the
continue the procedure with
If the required IP link is shown in the rtrv-ip-lnk output, but the IP host is not shown in the
rtrv-ip-host output in
Adding an IP Host
If the required IP host was shown in
output in this step. Perform
is assigned to the IP host.
Note: The rtrv-ip-host output must contain a host name for the association's lhost parameter
and a host name for the association's alhost parameter, if the alhost parameter will be specified
for the association. The IP address of the IP link should be assigned to the host name, shown in the
rtrv-ip-host output, that will be used as the association's lhost parameter value. If the alhost
parameter will be specified for the association, the IP address of the IP link must be assigned to
the host name that will be used as the alhost parameter value. The IP links associated with the
association's lhost and alhost values must be assigned to the same card.
7. Display the application running on the IP card shown in
IP host using the rept-stat-card command specifying the location of the IP card.
For this example, enter this command.
rept-stat-card:loc=1205
This is an example of the possible output.
rlghncxa03w 08-04-27 17:00:36 GMT EAGLE5 38.0.0
CARD VERSION
1205 114-000-000
ALARM STATUS
BPDCM GPL
IMT BUS A
IMT BUS B
SIGNALING LINK STATUS
SLK
A
A3
B2
Command Completed.
910-6278-001 Revision A, January 2012
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
255.255.255.0
Configuring an IP Link
Step 11.
Step 5, assign the IP address of the IP link to the IP host name using the
procedure. Then continue the procedure with
Step
Step 7 to verify the application running on the card whose IP address
TYPE GPL
DCM IPLIM
= No Alarms.
= 002-102-000
= Conn
= Conn
PST
IS-NR
IS-NR
IS-NR
IETF M2PA Configuration Procedures
FULL
FULL
FULL
FULL
FULL
FULL
FULL
procedure. After the IP link has been added,
5, the required IP link is shown in the rtrv-ip-lnk
Step 6
PST
IS-NR
LS CLLI
e5e6a -----------
e5e6a -----------
e5e6a -----------
100 DIX NO
10 DIX NO
100 DIX NO
100 DIX NO
100 DIX NO
10 DIX NO
100 DIX NO
10 DIX NO
100 DIX NO
10 DIX NO
100 DIX NO
10 DIX NO
Adding an IP Host
procedure. Then
Step 11.
whose IP address is assigned to the
SST AST
Active -----
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
208