Siemens SINAMICS S110 List Manual page 78

Parameter
List of parameters
Dependency: The number of pole pairs (r0313) is automatically re-calculated when the parameter is changed (together with
p0311), if p0314 = 0.
If p0310 is changed during quick commissioning (p0010 = 1), then the maximum speed p1082, which is also asso-
ciated with quick commissioning, is pre-assigned accordingly.
Refer to: p0311, r0313, p0314
Caution: When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Infor-
mation in p0300 should be carefully observed when removing write protection.
Notice: If p0310 is changed during quick commissioning (p0010 = 1), the maximum speed p1082, which is also associated
with quick commissioning, is pre-assigned accordingly. This is not the case when commissioning the motor (p0010
= 3).
Note: For synchronous motors, the parameter is not required and must therefore be pre-assigned zero. For p0310 = 0, it
is not possible to calculate the pole pair; instead, it must be entered in p0314.
p0311[0...n] Rated motor speed / Mot n_rated
SERVO_S110-CAN, Can be changed: C2(1, 3)
SERVO_S110-DP,
Data type: FloatingPoint32
SERVO_S110-PN
P-Group: Motor
Not for motor type: -
Min
0.0 [rpm]
Description: Sets the rated motor speed (rating plate).
Dependency: If p0311 is changed and for p0314 = 0, the pole pair (r0313) is re-calculated automatically.
Refer to: p0310, r0313, p0314
Caution: When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Infor-
mation in p0300 should be carefully observed when removing write protection.
Notice: If p0311 is changed during quick commissioning (p0010 = 1), the maximum speed p1082, which is also associated
with quick commissioning, is pre-assigned accordingly. This is not the case when commissioning the motor (p0010
= 3).
p0312[0...n] Rated motor torque / Mot M_rated
SERVO_S110-CAN, Can be changed: C2(3)
SERVO_S110-DP,
Data type: FloatingPoint32
SERVO_S110-PN
P-Group: Motor
Not for motor type: ASM, REL, FEM
Min
0.00 [Nm]
Description: Sets the rated motor torque (rating plate).
Caution: When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Infor-
mation in p0300 should be carefully observed when removing write protection.
r0313[0...n] Motor pole pair number, actual (or calculated) / Mot PolePairNo act
SERVO_S110-CAN, Can be changed: -
SERVO_S110-DP,
Data type: Unsigned16
SERVO_S110-PN
P-Group: Motor
Not for motor type: -
Min
-
Description: Displays the number of motor pole pairs. The value is used for internal calculations.
r0313 = 1: 2-pole motor
r0313 = 2: 4-pole motor, etc.
Dependency: For p0314 > 0, the entered value is displayed in r0313.
For p0314 = 0, the pole pair number (r0313) is automatically calculated from the rated frequency (p0310) and the
rated speed (p0311).
Refer to: p0310, p0311, p0314
1-78
Calculated: -
Dynamic index: MDS, p0130
Units group: -
Scaling: -
Max
210000.0 [rpm]
Calculated: -
Dynamic index: MDS, p0130
Units group: 7_4
Scaling: -
Max
1000000.00 [Nm]
Calculated: -
Dynamic index: MDS, p0130
Units group: -
Scaling: -
Max
-
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
Access level: 1
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0.0 [rpm]
Access level: 3
Func. diagram: -
Unit selection: p0100
Expert list: 1
Factory setting
0.00 [Nm]
Access level: 2
Func. diagram: 5300
Unit selection: -
Expert list: 1
Factory setting
-