Siemens SINAMICS S110 List Manual page 41

p0045 Smoothing time constant, display values / T_smth display
SERVO_S110-CAN, Can be changed: U, T
SERVO_S110-DP,
Data type: FloatingPoint32
SERVO_S110-PN
P-Group: -
Not for motor type: -
Min
0.00 [ms]
Description: Sets the smoothing time constant for the following display values:
SERVO: r0078[1], r0079[1], r0081 (calculated from the quantities smoothed with p0045), r0082[1].
VECTOR: r0063[1], r0068[1], r0080[1], r0082[1].
r0046.0...31 CO/BO: Missing enable sig / Missing enable sig
SERVO_S110-CAN, Can be changed: -
SERVO_S110-DP,
Data type: Unsigned32
SERVO_S110-PN
P-Group: Displays, signals
Not for motor type: -
Min
-
Description: Displays missing enable signals that are preventing the closed-loop drive control from being commissioned.
Bit field: Bit Signal name
00 OFF1 enable missing
01 OFF2 enable missing
02 OFF3 enable missing
03 Operation enable missing
04 Armature short-circuit / DC braking, enable
missing
05 STOP2 enable missing
06 STOP1 enable missing
08 EP terminals enable missing
09 Infeed enable missing
10 Ramp-function generator enable missing
11 Ramp-function generator start missing
12 Setpoint enable missing
16 OFF1 enable internal missing
17 OFF2 enable internal missing
18 OFF3 enable internal missing
19 Pulse enable internal missing
20 Armature short-circuit/DC braking internal
enable missing
21 STOP2 enable internal missing
22 STOP1 enable internal missing
25 Function bypass active
26 Drive inactive or not operational
27 De-magnetizing not completed
28 Brake open missing
29 Cooling system ready signal missing
30 Speed controller inhibited
31 Jog setpoint active
Dependency: Refer to: r0002
Note: The value r0046 = 0 indicates that all enable signals for this drive are present.
Bit 00 = 1 (enable signal missing), if:
- the signal source in p0840 is a 0 signal.
- there is a "switching on inhibited".
Bit 01 = 1 (enable signal missing), if:
- the signal source in p0844 or p0845 is a 0 signal.
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
Calculated: -
Dynamic index: -
Units group: -
Scaling: -
Max
1000.00 [ms]
Calculated: -
Dynamic index: -
Units group: -
Scaling: -
Max
-
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Parameter
List of parameters
Access level: 2
Func. diagram: 4715, 5610,
5730, 6714, 8012
Unit selection: -
Expert list: 1
Factory setting
1.00 [ms]
Access level: 1
Func. diagram: 2634
Unit selection: -
Expert list: 1
Factory setting
-
0 signal FP
No -
No -
No -
No -
No 7014,
7016
No -
No -
No -
No -
No -
No -
No -
No -
No -
No -
No -
No 7014,
7016
No -
No -
No -
No -
No -
No -
No -
No -
No -
1-41