Siemens SINAMICS S110 List Manual page 108

Parameter
List of parameters
In the following cases, copying is automatically started in the following cases:
1.) When commissioning 1FT6, 1FK6, 1FK7 motors.
2.) When writing into p0431.
3.) For p1990 = 1.
p0440 is automatically set to 0 when the copying has been completed.
In order to permanently accept the copied values, it is necessary to save in a non-volatile fashion (p0977).
p0441[0...n] Encoder commissioning serial number part 1 / Enc comm ser_no 1
SERVO_S110-CAN, Can be changed: C2(4)
SERVO_S110-DP,
Data type: Unsigned32
SERVO_S110-PN
P-Group: Encoder
Not for motor type: -
Min
0000 hex
Description: Serial number part 1 of the encoder for the commissioning.
Dependency: Refer to: p0440, p0442, p0443, p0444, p0445, r0460, r0461, r0462, r0463, r0464
Refer to: F07414
Note: A value of zero is displayed if an encoder is not present.
p0442[0...n] Encoder commissioning serial number part 2 / Enc comm ser_no 2
SERVO_S110-CAN, Can be changed: C2(4)
SERVO_S110-DP,
Data type: Unsigned32
SERVO_S110-PN
P-Group: Encoder
Not for motor type: -
Min
0000 hex
Description: Serial number part 2 of the encoder for the commissioning.
Dependency: Refer to: p0440, p0441, p0443, p0444, p0445, r0460, r0461, r0462, r0463, r0464
Refer to: F07414
Note: A value of zero is displayed if an encoder is not present.
p0443[0...n] Encoder commissioning serial number part 3 / Enc comm ser_no 3
SERVO_S110-CAN, Can be changed: C2(4)
SERVO_S110-DP,
Data type: Unsigned32
SERVO_S110-PN
P-Group: Encoder
Not for motor type: -
Min
0000 hex
Description: Serial number part 3 of the encoder for the commissioning.
Dependency: Refer to: p0440, p0441, p0442, p0444, p0445, r0460, r0461, r0462, r0463, r0464
Refer to: F07414
Note: A value of zero is displayed if an encoder is not present.
p0444[0...n] Encoder commissioning serial number part 4 / Enc comm ser_no 4
SERVO_S110-CAN, Can be changed: C2(4)
SERVO_S110-DP,
Data type: Unsigned32
SERVO_S110-PN
P-Group: Encoder
Not for motor type: -
Min
0000 hex
Description: Serial number part 4 of the encoder for the commissioning.
1-108
Calculated: CALC_MOD_ALL
Dynamic index: EDS, p0140
Units group: -
Scaling: -
Max
FFFF FFFF hex
Calculated: CALC_MOD_ALL
Dynamic index: EDS, p0140
Units group: -
Scaling: -
Max
FFFF FFFF hex
Calculated: CALC_MOD_ALL
Dynamic index: EDS, p0140
Units group: -
Scaling: -
Max
FFFF FFFF hex
Calculated: CALC_MOD_ALL
Dynamic index: EDS, p0140
Units group: -
Scaling: -
Max
FFFF FFFF hex
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 hex
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 hex
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 hex
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 hex