Siemens SINAMICS S110 List Manual page 737

p1441[0...n]
p1451[0...n]
p1456[0...n]
p1457[0...n]
p1458[0...n]
p1459[0...n]
p1460[0...n]
p1461[0...n]
p1462[0...n]
p1463[0...n]
p1464[0...n]
p1465[0...n]
p1470[0...n]
p1472[0...n]
p1494[0...n]
p1498[0...n]
p1517[0...n]
p1520[0...n]
p1521[0...n]
p1524[0...n]
p1525[0...n]
p1530[0...n]
p1531[0...n]
p1532[0...n]
p1578[0...n]
p1579[0...n]
p1581[0...n]
p1585[0...n]
p1590[0...n]
p1592[0...n]
p1612[0...n]
p1656[0...n]
p1657[0...n]
p1658[0...n]
p1659[0...n]
p1660[0...n]
p1661[0...n]
p1662[0...n]
p1663[0...n]
p1664[0...n]
p1665[0...n]
p1666[0...n]
p1701[0...n]
p1715[0...n]
p1717[0...n]
p1752[0...n]
p1755[0...n]
p1800[0...n]
p1821[0...n]
p2140[0...n]
p2141[0...n]
p2142[0...n]
p2149[0...n]
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
Actual speed smoothing time / n_act T_smooth
Speed actual value smoothing time sensorless / n_act t_sm SL
Speed controller P gain adaptation lower starting point / n_ctrl AdaptKpLow
Speed controller P gain adaptation upper starting point / n_ctrl AdaptKp up
Adaptation factor, lower / Adapt_factor lower
Adaptation factor, upper / Adapt_factor upper
Speed controller P gain adaptation speed, lower / n_ctrl Kp n lower
Speed controller Kp adaptation speed, upper scaling / n_ctrl Kp n upper
Speed controller integral time adaptation speed lower / n_ctrl Tn n lower
Speed controller Tn adaptation speed, upper scaling / n_ctrl Tn n upper
Speed controller adaptation speed, lower / n_ctrl n lower
Speed controller adaptation speed, upper / n_ctrl n upper
Speed controller encoderless operation P-gain / n_ctrl SLVC Kp
Speed controller encoderless operation integral time / n_ctrl SLVC Tn
Speed controller integrator feedback time constant / n_ctr integ_fdbk T
Load moment of inertia / Load mom of inert
Accelerating torque smoothing time constant / M_accel T_smooth
CO: Torque limit upper/motoring / M_max upper/mot
CO: Torque limit lower/regenerative / M_max lower/regen
CO: Torque limit upper/motoring scaling / M_max up/mot scal
CO: Torque limit lower/regenerative scaling / M_max low/gen scal
Power limit motoring / P_max mot
Power limit regenerative / P_max gen
CO: Torque limit offset / M_max offset
Flux reduction flux decrease smoothing time / Flux red dec t_sm
Flux reduction flux build-up smoothing time / Flux red up t_sm
Flux reduction factor / Flux red factor
Flux actual value, smoothing time / Flux actVal T_smth
Flux controller P gain / Flux controller Kp
Flux controller integral time / Flux controller Tn
Current setpoint, open-loop control, encoderless / I_setCtrEncoderl
Activates current setpoint filter / I_setp_filt act
Current setpoint filter 1 type / I_set_filt 1 Typ
Current setpoint filter 1 denominator natural frequency / I_set_filt 1 fn_n
Current setpoint filter 1 denominator damping / I_set_filt 1 D_n
Current setpoint filter 1 numerator natural frequency / I_set_filt 1 fn_z
Current setpoint filter 1 numerator damping / I_set_filt 1 D_z
Current setpoint filter 2 type / I_set_filt 2 Typ
Current setpoint filter 2 denominator natural frequency / I_set_filt 2 fn_n
Current setpoint filter 2 denominator damping / I_set_filt 2 D_n
Current setpoint filter 2 numerator natural frequency / I_set_filt 2 fn_z
Current setpoint filter 2 numerator damping / I_set_filt 2 D_z
Current controller reference model dead time / I_ctrRefMod t_dead
Current controller P gain / I_ctrl Kp
Current controller integral-action time / I_ctrl Tn
Motor model changeover speed operation with encoder / MotMod n_chgov enc
Motor model changeover speed encoderless operation / MotMod n_chgSnsorl
Pulse frequency setpoint / Pulse freq setp
Dir of rot / Dir of rot
Hysteresis speed 2 / n_hysteresis 2
Speed threshold 1 / n_thresh val 1
Hysteresis speed 1 / n_hysteresis 1
Monitoring configuration / Monit config
Parameter
Parameters for data sets
1-737