Siemens SINAMICS S110 List Manual page 158

Parameter
List of parameters
Index: [0] = Digital inputs/outputs (DI/DO)
[1] = Analog inputs (AI)
[2] = Not available - analog outputs (AO)
Dependency: The parameter can only be modified for p0009 = 3, 29.
Refer to: p0009
Note: The changed sampling time is immediately effective after a completed sub-boot (p0009 -> 0).
p0802 Data transfer: memory card as source/target / mem_card src/targ
CU_S110-CAN, Can be changed: T
CU_S110-DP,
Data type: Integer16
CU_S110-PN
P-Group: -
Not for motor type: -
Min
0
Description: Sets the number for data transfer of a parameter backup from/to memory card.
Transfer from memory card to device memory (p0804 = 1):
- Sets the source of parameter backup (e.g. p0802 = 48 --> PS048xxx.ACX is the source).
Transfer from non-volatile device memory to memory card (p0804 = 2):
- Sets the target of parameter backup (e.g. p0802 = 23 --> PS023xxx.ACX is the target).
No setting is required for the transfer of the communication configuration (p0804 = 12).
Dependency: Refer to: p0803, p0804
Notice: If the data between the volatile and non-volatile device memories differ, then it may be necessary to save the data
on the memory card in a non-volatile fashion prior to the transfer (e.g. p0971 = 1).
p0803 Data transfer: device memory as source/target / Dev_mem src/targ
CU_S110-CAN, Can be changed: T
CU_S110-DP,
Data type: Integer16
CU_S110-PN
P-Group: -
Not for motor type: -
Min
0
Description: Sets the number for data transfer of a parameter backup from/to device memory.
Transfer from memory card to device memory (p0804 = 1):
- Sets the target of the parameter backup (e.g. p0803 = 10 --> PS010xxx.ACX is the target).
Transfer from non-volatile device memory to memory card (p0804 = 2):
- Sets the source of the parameter backup (e.g. p0803 = 11 --> PS011xxx.ACX is the source).
No setting is required for the transfer of the communication configuration (p0804 = 12).
Value: 0:
10:
11:
12:
Dependency: Refer to: p0802, p0804
Notice: If the data between the volatile and non-volatile device memories differ, then it may be necessary to save the data
on the memory card in a non-volatile fashion prior to the transfer (e.g. p0971 = 1).
p0804 Data transfer start / Data transf start
CU_S110-CAN, Can be changed: T
CU_S110-DP,
Data type: Integer16
CU_S110-PN
P-Group: -
Not for motor type: -
Min
0
Description: Sets the transfer direction and start of data transfer between the memory card and non-volatile device memory.
1-158
Source/target standard
Source/target with setting 10
Source/target with setting 11
Source/target with setting 12
Calculated: -
Dynamic index: -
Units group: -
Scaling: -
Max
100
Calculated: -
Dynamic index: -
Units group: -
Scaling: -
Max
12
Calculated: -
Dynamic index: -
Units group: -
Scaling: -
Max
1100
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0