Page 1 MSC1000G/1024G/1224G Series Management Switch Card User’s Guide Version 3.94 10/2009 Edition 2 www.zyxel.com...
Page 3: About This User's Guide
Please refer to www.zyxel.com for additional support documentation and product certifications. Documentation Feedback Send your comments, questions or suggestions to: techwriters@zyxel.com.tw Thank you! The Technical Writing Team, ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 30099, Taiwan. MSC1000G/1024G/1224G Series User’s Guide...
Page 4 About This User's Guide Need More Help? More help is available at www.zyxel.com. • Download Library Search for the latest product updates and documentation from this link. Read the Tech Doc Overview to find out how to efficiently use the documentation in order to better understand how to use your product.
Page 5: Document Conventions
Document Conventions Document Conventions Warnings and Notes These are how warnings and notes are shown in this User’s Guide. Warnings tell you about things that could harm you or your device. Notes tell you other important information (for example, other things you may need to configure or helpful tips) or recommendations.
Page 6 Document Conventions • The VLC1424G-56 for VDSL2 over POTS (Annex A) Line Card may be referred to as the “VLC1424G”, the “VLC” or the “line card” in this User’s Guide. • The ELC1220G-55 Fiber-based Fast Ethernet Line Card may be referred to as the “ELC1220G”, the “ELC”...
Page 7: Safety Warnings
Safety Warnings Safety Warnings For your safety, be sure to read and follow all warning notices and instructions. • Do NOT use this product near water, for example, in a wet basement or near a swimming pool. • Do NOT expose your device to dampness, dust or corrosive liquids. •...
Page 8 Safety Warnings MSC1000G/1024G/1224G Series User’s Guide...
Page 9: Table Of Contents
Contents Overview Contents Overview Introduction ..........................41 Getting to Know Your MSC ......................43 Hardware Connections ......................55 Web Configurator ........................61 The Web Configurator ....................... 63 Tutorials ............................. 77 Access Control List Screens ...................... 93 Alarm Screens ......................... 143 Cluster Screens ........................
Page 10 Contents Overview show Commands ........................819 switch Commands ........................867 sys Commands ........................905 vlan Commands ........................933 voip Commands ........................937 Firmware and Configuration File Maintenance ................ 961 Troubleshooting and Product Specifications ..............967 Troubleshooting ........................969 Product Specifications ......................979 Appendices and Index ......................
Page 11: Table Of Contents
Table of Contents Table of Contents About This User's Guide ......................3 Document Conventions......................5 Safety Warnings........................7 Contents Overview ........................9 Table of Contents........................11 Part I: Introduction................. 41 Chapter 1 Getting to Know Your MSC ....................43 1.1 Introduction .......................... 43 1.1.1 Applications ........................
Page 12 Table of Contents 3.6.1 Card Status Details ....................75 Chapter 4 Tutorials ........................... 77 4.1 Initial Configuration ......................77 4.2 H.248 Configuration Example ....................79 4.3 IMA Configuration Example ....................84 4.4 Changing the Default Management PVC VLAN ID to Other than 1 or 0 ......89 Chapter 5 Access Control List Screens ....................
Page 13 Table of Contents 5.17.2 DSCP Port Screen ....................127 5.17.3 DSCP Port Slot Screen ..................129 5.18 PPPoE Screen ......................... 130 5.19 Loop Guard ........................132 5.20 Loop Guard Setup ......................134 5.20.1 Loop Guard Slot Screen ..................136 5.21 Subnet Based VLANs ..................... 137 5.22 Configuring Subnet Based VLAN ..................
Page 14 Table of Contents 8.11 IMA Loopback Screen ...................... 185 Chapter 9 Maintenance Screens ......................189 9.1 Configuration Backup Screen ..................189 9.2 Configuration Restore Screen ..................189 9.3 Configuration Reset Screen ....................190 9.4 Firmware Upgrade Screen ....................191 9.5 Reboot Screen ........................192 Chapter 10 Multicast Screens .........................
Page 15 Table of Contents 11.2.10 Rate Adaption ....................... 213 11.2.11 RFI (Radio Frequency Interference) ..............213 11.3 Downstream and Upstream ..................... 213 11.4 DSL Profiles ........................213 11.5 Alarm Profiles ........................214 11.6 Default Settings ........................ 214 11.7 ADSL Port Setup ......................214 11.7.1 ADSL Port Setup Line Card Screen ...............
Page 16 Table of Contents 11.19.1 IPBPVC VLAN Setup Screen ................272 11.19.2 IPBPVC by Slot Screen ..................273 11.20 IPB Route Screen ......................274 11.21 G.bond Screen ....................... 276 11.22 The VoIP SIP Port Setup Screen ................... 279 11.23 The SIP Port Setup Line Card Screen ................282 11.24 Advanced SIP Port Setup Screen ..................
Page 17 Table of Contents 13.4 ADSL Profile Screen ......................326 13.5 VDSL Profile Setup ......................329 13.6 VDSL2 Profiles ........................ 332 13.6.1 VDSL2 Profiles ....................... 332 13.6.2 VDSL2 Profile Example ..................333 13.7 VDSL2 Template Setup ....................333 13.7.1 VDSL2 Line Profile Setup ..................334 13.7.2 VDSL2 Line Profile Setup >...
Page 18 Table of Contents 13.27 VoIP Dial Plan Profile Screen ..................394 13.28 Alarm E1 Profile Screen ....................395 Chapter 14 Statistics Screens ......................... 397 14.1 ARP Table ........................397 14.1.1 How ARP Works ....................397 14.2 ARP Table Screen ......................397 14.3 DHCP ..........................
Page 19 Table of Contents 14.22 OAM Statistics ....................... 450 14.23 IMA Statistics ......................... 451 14.23.1 IMA Group Statistics ..................... 452 14.23.2 IMA Group Details ....................453 14.23.3 Link Details ......................456 14.23.4 Link 15Min ......................458 14.23.5 Link 1Day ......................460 14.23.6 Link Last24hr ......................
Page 20 Table of Contents 15.12 Switch Port Setup Port Screen ..................492 15.13 Switch Port Setup 802.1P/1Q Screen ................493 15.14 Switch Port Setup Bandwidth Screen ................493 15.15 Switch Port Setup Broadcast Screen ................494 15.16 Switch Port Setup DSCP ....................495 15.16.1 Switch Port Setup DSCP Screen .................
Page 21 Table of Contents 17.3 Automatic VLAN Registration ..................532 17.3.1 GARP ........................532 17.3.2 GVRP ........................533 17.4 Tagged Frames Forwarding Example ................533 17.5 Untagged Frames Forwarding Example ................533 17.6 VLAN Setup Screen ......................534 17.7 VLAN Port Setting Screen ....................535 17.8 VLAN Port Setting Slot Screen ..................
Page 22 Table of Contents Part III: Commands ................575 Chapter 20 Commands ..........................577 20.1 Commands Introduction ....................577 20.2 Command Conventions ....................577 20.3 Getting Help ........................578 20.3.1 List of Available Commands ................... 578 20.3.2 Detailed Command Information ................578 20.4 Common Command Notation ..................
Page 23 Table of Contents 21.6.1 acl dot1x disable Command ................... 597 21.6.2 acl dot1x enable Command ................... 597 21.6.3 acl dot1x port control Command ................597 21.6.4 acl dot1x port disable Command ................597 21.6.5 acl dot1x port enable Command ................597 21.6.6 acl dot1x port period Command ................
Page 24 Table of Contents 21.12.7 acl pppoeagent set Command ................609 21.12.8 acl pppoeagent show Command ................609 21.13 acl rule Commands ....................... 610 21.13.1 acl rule delete Command ..................610 21.13.2 acl rule nomatch Command ................. 610 21.13.3 acl rule set Command ..................610 21.13.4 acl rule show Command ..................611 21.14 acl usbcastctrl Commands .....................611 21.14.1 acl usbcastctrl set ....................611...
Page 25 Table of Contents 24.2.8 cluster member set Command ................625 24.2.9 cluster member show Command ................626 24.2.10 cluster show Command ..................626 24.2.11 cluster vlan Command ..................627 24.3 Cluster Member Firmware and Configuration File Management ........628 Chapter 25 config Commands.........................
Page 26 Table of Contents 27.1 General ima Command Parameters ................645 27.2 ima Commands Summary ....................645 27.3 ima group Commands ..................... 649 27.4 ima mgtpvc Commands ....................652 27.5 ima pvc Commands ......................654 27.6 ima dtpvc Commands ...................... 654 Chapter 28 ip Commands ........................
Page 27 Table of Contents 30.4 multicast Group MAC Address Commands ..............674 30.4.1 multicast groupmacaddr del Command ..............674 30.4.2 multicast groupmacaddr set Command ..............674 30.4.3 multicast groupmacaddr show Command ............. 675 30.5 multicast fastleave Commands ..................675 30.5.1 multicast igmp fastleave enable Command ............675 30.5.2 multicast igmp fastleave disable Command ............
Page 28 Table of Contents Chapter 31 port Commands ........................687 31.1 General port Command Parameters ................687 31.2 port Commands Summary ....................687 31.3 port Commands ....................... 700 31.4 port adsl Commands ....................... 700 31.4.1 port adsl alarmprof Command ................700 31.4.2 port adsl annexl disable Command ................
Page 29 Table of Contents 31.10.10 port enet pvid Command ..................713 31.10.11 port enet ratelimit Command ................714 31.10.12 port enet show Command .................. 714 31.10.13 port enet tls Commands ..................714 31.10.14 port enet vlan Commands .................. 715 31.11 G.bond Commands ......................715 31.11.1 port gbond set Command ..................
Page 30 Table of Contents 31.24.1 port paepvc delete Command ................730 31.24.2 port paepvc set Command .................. 731 31.24.3 port paepvc show Command ................731 31.25 port pots gain Command ....................731 31.26 port ppvc Commands ....................732 31.26.1 port ppvc delete Command .................. 732 31.26.2 port ppvc member delete Command ..............
Page 31 Table of Contents 31.34.8 port vdsl limitmask set Command ................ 746 31.34.9 port vdsl limitmask show Command ..............747 31.34.10 port vdsl priority Command ................748 31.34.11 port vdsl pvid Command ..................748 31.34.12 port vdsl pvlan set Command ................748 31.34.13 port vdsl rfiband Command ................
Page 32 Table of Contents 32.9.1 profile alarmvdsl show Command ................781 32.9.2 profile alarmvdsl set Command ................782 32.9.3 profile alarmvdsl delete Command ................. 783 32.9.4 profile alarmvdsl map Command ................783 32.10 profile atm Commands ....................783 32.10.1 profile atm show Command ................. 784 32.10.2 profile atm set Command ..................
Page 33 Table of Contents 32.18.2 profile voip dsp map Command ................803 32.18.3 profile voip dsp set Command ................804 32.18.4 profile voip dsp show Command ................805 32.19 profile voip h248 Commands ..................806 32.19.1 profile voip h248 delete Command ..............806 32.19.2 profile voip h248 map Command .................
Page 34 Table of Contents 33.3.15 show ipbpvc interface Command ................. 842 33.3.16 show ipbpvc route Command ................842 33.3.17 show lineinfo Command ..................843 33.3.18 show linerate Command ..................845 33.3.19 show linestat Command ..................846 33.3.20 show mac Command ................... 846 33.3.21 show monitor Command ..................
Page 35 Table of Contents 34.5.3 switch cfm Commands ................... 875 34.6 switch dot3ad Commands ....................880 34.6.1 switch dot3ad lacp priority Command ..............881 34.6.2 switch dot3ad lacp timeout Command ..............881 34.6.3 switch dot3ad lacp show Command ..............881 34.6.4 switch dot3ad enable Command ................882 34.6.5 switch dot3ad disable Command ................
Page 36 Table of Contents 34.12 switch port Commands ....................895 34.12.1 switch port disable Command ................895 34.12.2 switch port enable Command ................895 34.12.3 switch port flowctrl disable Command ..............896 34.12.4 switch port flowctrl enable Command ..............896 34.12.5 switch port frametype Command ................. 896 34.12.6 switch port gvrp Commands ................
Page 37 Table of Contents 35.3.15 sys info chassis Command .................. 915 35.3.16 sys info contact Command ................... 916 35.3.17 sys info frame Command ..................916 35.3.18 sys info hostname Command ................916 35.3.19 sys info location Command .................. 917 35.3.20 sys info show Command ..................917 35.3.21 sys monitor set Command ...................
Page 38 Table of Contents 36.3 vlan Commands ....................... 933 36.3.1 vlan delete Command .................... 933 36.3.2 vlan disable Command ................... 934 36.3.3 vlan enable Command ................... 934 36.3.4 vlan name Command ..................... 934 36.3.5 vlan set Command ....................934 36.3.6 vlan show Command ....................935 Chapter 37 voip Commands ........................
Page 39 Table of Contents 37.10.2 voip sip dialplan map Command ................952 37.10.3 voip sip dialplan set Command ................953 37.10.4 voip sip dialplan show Command ................. 954 37.11 voip sip keypattern Commands ..................955 37.11.1 voip sip keypattern set Command ................ 955 37.11.2 voip sip keypattern show Command ..............
Page 40 Table of Contents 39.9 IMA Connnection Failure ....................976 Chapter 40 Product Specifications ......................979 40.1 IES Default Settings ......................979 40.2 Specifications ........................983 40.3 Features .......................... 987 40.4 Firmware Naming Conventions ..................991 40.5 Console Port Pin Assignments ..................992 40.6 MSC1000G ALARM Connector Pin Assignments ............
Page 41: Introduction
Introduction Getting to Know Your MSC (43) Hardware Connections (55)
Page 43: Getting To Know Your Msc
H A P T E R Getting to Know Your MSC This chapter introduces the main applications of the MSC. It also introduces the ways you can manage the MSC. 1.1 Introduction The IES-5000 and IES-6000 series are perfect for ISPs or large building applications seeking to provide high bandwidth broadband services to subscribers while minimizing costs.
Page 44 Chapter 1 Getting to Know Your MSC Figure 1 MTU Application • The IES-5000 or IES-6000 provides DSL service over telephone wires to subscribers in a Central Office (CO) application. The following figure shows the IES-5000 set up in a telephone company’s central office.
Page 45 Chapter 1 Getting to Know Your MSC Figure 2 Central Office Application • Other applications include telemedicine, surveillance systems, remote servers systems, cellular base stations and high-quality videoconferencing. IMA Application Although IP network is common today, there are still some countries using TDM (Time- Division Multiplex) as their backbone network.
Page 46 Chapter 1 Getting to Know Your MSC Figure 3 IMA Application Remote CO Site Site IMA-2 IMA-1 xDSL one E1 line Remote Site Traffic Flow Scenario In remote sites, traffic coming from subscribers through a DSL line card is sent to the MSC management card and then forwarded to the specified IMA card in your configuration.
Page 47: Ways To Manage The Msc
Chapter 1 Getting to Know Your MSC Figure 5 Remote Site Traffic Flow Scenario Central Office Site Traffic Flow Scenario Unlike the remote site, in the central office, traffic from each IMA line card of the IES is directly forwarded to the MSC and the connected Ethernet (IP) network. The following figure shows an example.
Page 48: Features
Chapter 1 Getting to Know Your MSC • Web Configurator. This is GUI-based management using a (supported) web browser. See Chapter 3 on page • Command Line Interface. Use line commands through Telnet or the console port to manage the MSC. See Chapter 20 on page 577.
Page 49 Chapter 1 Getting to Know Your MSC DHCP Relay Option82 The system supports DHCP relay agent82 (RFC 3046) that adds additional information to client DHCP requests that the MSC relays to a DHCP server. It also supports adding the sub- option 2 (Remote ID) with additional information.
Page 50 Chapter 1 Getting to Know Your MSC Link Aggregation Control Protocol (LACP) The MSC supports the link aggregation IEEE 802.3ad protocol. Link aggregation (trunking) is the grouping of physical ports into one logical higher-capacity link. You may want to trunk ports if for example, it is cheaper to use multiple lower-speed links than to under-utilize a high-speed, but more costly, single-port link.
Page 51 Chapter 1 Getting to Know Your MSC PPPoA-to-PPPoE (PAE) PVC This feature allows the system to translate PPPoA packets to PPPoE packets (and vice versa) to allow communication between CPE clients and an access concentrator (such as a BRAS) through the switch. PPPoE Intermediate Agent Information Similar to DHCP relay option82, you can set the system to insert line information into client PPPoE Active Discovery Initialization (PADI) packets.
Page 52 Chapter 1 Getting to Know Your MSC Static Multicast Use static multicast to allow incoming frames based on multicast MAC address(es) that you specify. This feature can be used in conjunction with IGMP snooping to allow multicast MAC address(es) that are not learned by IGMP snooping. You can use static multicast to pass routing protocols, such as RIP and OSPF.
Page 53 Chapter 1 Getting to Know Your MSC Alarm LED An ALM (alarm) LED lights when the second power source is not connected, the IES-5000 is overheated, the voltage readings are outside the tolerance levels a fan fails or another alarm with a severity level of MAJOR or CRITICAL occurs.
Page 54 Chapter 1 Getting to Know Your MSC IP-aware Bridging The line cards can forward frames based on the destination IP address, instead of the destination MAC address, and replace the source MAC address with its own MAC address. This provides better scalability and security for large-scale access networks, especially with Ethernet.
Page 55: Hardware Connections
H A P T E R Hardware Connections This chapter introduces the MSC’s hardware and how to connect it. Refer to the IES-6000M or IES-5000 Series User’s Guide for directions and safety warnings on installing the management switch card. Use this chapter’s port and slot descriptions to connect the management switch card. 2.1 Front Panel Figure 7 MSC100G Front Panel Figure 8 MSC1024G Front Panel...
Page 56 Chapter 2 Hardware Connections Table 1 Management Switch Card LED Descriptions COLOR STATUS DESCRIPTION Green Blinking The system is initializing. The management switch card is on and functioning properly. The management switch card is not receiving power, is not ready or has malfunctioned.
Page 57: Ports And Connections
Chapter 2 Hardware Connections 2.3 Ports and Connections Install the MSC before you make the hardware connections. Refer to the IES- 6000M or IES-5000 Series User’s Guide for installation instructions. Table 2 Front Panel Descriptions LABEL DESCRIPTION ALARM This DB15F connector is for connecting to alarm input and alarm output terminals on other pieces of equipment.
Page 58: Gigabit And 10 Gigabit Ethernet Interfaces
Chapter 2 Hardware Connections • Pins 3 and 11 are alarm input three. The MSC signals an alarm when it detects an alarm on the ALARM input pins, the IES-5000 is overheated, the voltage readings are outside the tolerance levels a fan fails or another alarm occurs.
Page 59 Chapter 2 Hardware Connections Use the subtending mode to daisy-chain other Ethernet switches. With subtending mode, the management switch card allows traffic between the ports in subtending mode and the ports in uplink mode. The management switch card does not allow traffic between the ports in subtending mode and the DSL ports on the line cards.
Page 60 Chapter 2 Hardware Connections Figure 11 Transceiver Installation Figure 12 Installed Transceiver 2.3.2.4 Transceiver Removal Use the following steps to remove a mini GBIC transceiver (SFP module) from the slot. 1 Remove the fiber-optic cables from the transceiver. 2 Unlock the transceiver’s latch (latch styles vary). 3 Pull the transceiver out of the slot.
Page 61: Web Configurator
Web Configurator The Web Configurator (63) Tutorials (77) Access Control List Screens (93) Alarm Screens (143) Cluster Screens (169) Diagnostic Screens (175) Maintenance Screens (189) Multicast Screens (193) Subscriber Port Setup Screens (209) IMA Screens (309) Profile Screens (325) Statistics Screens (397) Switch Screens (473) Sys Screens (507) VLAN Screens (531)
Page 63: The Web Configurator
H A P T E R The Web Configurator This section introduces the configuration and functions of the web configurator. 3.1 Web Configurator Introduction The web configurator is an HTML-based management interface that allows easy system setup and management via Internet browser. Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions.
Page 64: Navigation Panel
Chapter 3 The Web Configurator Figure 15 Web Configurator: Login 4 Click OK to view the first web configurator screen. Figure 16 Web Configurator: First Screen 3.3 Navigation Panel In the navigation panel (the column on the left), click a main link to reveal a list of submenu links.
Page 65 Chapter 3 The Web Configurator Table 3 Navigation Panel Links (continued) LINK DESCRIPTION Downstream This link takes you to a screen where you can block downstream broadcast packets Broadcast from being sent to specified VLANs on specified ports. MAC Count This link takes you to a screen where you can limit the number of MAC addresses that can connect to a subscriber port.
Page 66 Chapter 3 The Web Configurator Table 3 Navigation Panel Links (continued) LINK DESCRIPTION This link takes you to a screen where you can perform LDM (Loop Diagnostic Mode) tests on a subscriber port. Loopback This link takes you to a screen where you can perform an OAM (Operational, Administration and Maintenance) F5 loopback test on a subscriber port or PVC.
Page 67 Chapter 3 The Web Configurator Table 3 Navigation Panel Links (continued) LINK DESCRIPTION This link takes you to screens where you can configure PVCs (Permanent Virtual Circuits) on subscriber ports. Copy This link takes you to a screen where you can copy port settings from a source port to destination ports on the same type of line card.
Page 68 Chapter 3 The Web Configurator Table 3 Navigation Panel Links (continued) LINK DESCRIPTION VoIP SIP This link takes you to a screen where you can configure VoIP SIP CALLSVC CALLSVC filter profiles. VoIP DSP This link takes you to a screen where you can configure VoIP DSP filter profiles.
Page 69 Chapter 3 The Web Configurator Table 3 Navigation Panel Links (continued) LINK DESCRIPTION This link takes you to a screen where you can view the Ethernet OAM (Operational, Administration and Maintenance) statistics for Ethernet line card ports. This link takes you to a screen where you can view E1 port statistics. Switch Switch Setup This link takes you to a screen where you can set up global switch parameters such...
Page 70 Chapter 3 The Web Configurator Table 3 Navigation Panel Links (continued) LINK DESCRIPTION Key Pattern This link takes you to a screen where you can configure the numbers to press to access VoIP services such as call waiting. Dialplan This link takes you to a screen where you can configure a VoIP dial plan (or number plan).
Page 71 Chapter 3 The Web Configurator Table 4 Web Configurator Screen Sub-links Details (continued) Maintenance Multicast Port Config Backup IGMP ADSL GROUP Config Restore IGMP Setup ADSL Port Setup Port Setup ADSL Port Setup Slot Config Reset DTPVC IGMP Port Setup Slot ADSL Port Setup Firmware Upgrade MGTPVC...
Page 72: Saving Your Configuration
Chapter 3 The Web Configurator Table 4 Web Configurator Screen Sub-links Details (continued) Profile Statistics Switch ADSL ARP Table Switch Setup Access Control VDSL DHCP General SNMP Dot3ad Access Ctrl VDSL2 MAC Table QSchedule Secured Client VDSL2 Line Profile IGMP Status Isolation General Setup VDSL2 Channel Profile...
Page 73: Logging Out Of The Web Configurator
Chapter 3 The Web Configurator Click Config Save in the navigation panel and then the Save button to save your configuration to nonvolatile memory. Nonvolatile memory refers to the switch's storage that remains even if the switch's power is turned off. Use Config Save when you are done with a configuration session.
Page 74 Chapter 3 The Web Configurator Figure 19 Web Configurator: Home Screen (System Info) The following table describes the labels in this screen. Table 5 System Info (Home) LABEL DESCRIPTION Current Alarm Click the links to view detailed alarm information (see Section 6.1 on page 143).
Page 75: Card Status Details
Chapter 3 The Web Configurator Table 5 System Info (Home) (continued) LABEL DESCRIPTION Monitor Error This field indicates if no line card status information can be obtained. Linecard Down This field indicates whether the line card has failed. Linecard Out This field indicates whether the line card is removed from its slot.
Page 76 Chapter 3 The Web Configurator MSC1000G/1024G/1224G Series User’s Guide...
Page 77: Tutorials
H A P T E R Tutorials This chapter contains instructions to quickly set up features on the system. • Initial Configuration (Section 4.1 on page • H.248 Configuration Example (Section 4.2 on page • IMA Configuration Example (Section 4.3 on page •...
Page 78 Chapter 4 Tutorials It is highly recommended that you use the sys reboot <seconds> command before using any settings or commands that may lock you out from managing the device. Use the sys reboot cancel command to cancel the scheduled reboot when you are sure you have the correct configuration. Otherwise, the device will restart and resume using the settings last saved before using the sys reboot command.
Page 79: Configuration Example
Chapter 4 Tutorials Select slot 7 and port 1, and click Load to display the settings as shown in this screen. Select Enable and click Apply. Figure 24 Enable the VDSL Port 6 Configure the IP address for A (for example, 192.168.1.33) and B (for example, 192.168.1.254).
Page 80 Chapter 4 Tutorials 1 Create an H.248 profile. Use the Profile > VoIP H248 screen (see Section 13.22 on page 371). • Enter the configuration information about the MGC, and give the profile a name. This example creates a profile named MEGACO for an MGC with an IP address 172.16.19.24 using the UDP transport method and the long encoding format.
Page 81 Chapter 4 Tutorials 2 Set the VOP card’s IP information. Use the VoIP > IP screen (see Section 18.6 on page 559). • Enter the Slot number of the H.248-enabled VoIP line card (3 in this example). • Set the VOP card’s IP address to 192.168.3.174. •...
Page 82 Chapter 4 Tutorials 4 Configure the H.248 interface. Use the VoIP > Interface screen (see Section 18.14 on page 570). • Select the number of the H.248 interface you want to configure (1 in this example) and click Load. • Enter the H.248 interface’s IP address and subnet mask for communicating with the MGC (172.16.19.200/24 in this example.
Page 83 Chapter 4 Tutorials 5 Set up termination names for the VOP card’s ports. Use the Port > VoIP H248 screen (see Section 11.25 on page 285). • In the middle section of the screen, select the Slot in which you installed the H.248- enabled VoIP line card (3 in this example).
Page 84: Ima Configuration Example
Chapter 4 Tutorials 6 Lastly, test your configuration by making a call from a phone connected to one of the ports you configured. Alternatively, use the show linestat <slot-port> command to check whether the relevant port is successfully registered with the MGC (the state should be “idle”).
Page 85 Chapter 4 Tutorials 1 Enable the E1 port. Click Port > E1. Select Slot 2 and Port 3, then click Load. Select Enable and then click Apply. Figure 31 Enable the E1 Port Example Check the port 3 LED. The LED should be orange. An orange LED indicates an alarm on the link.
Page 86 Chapter 4 Tutorials 4 Configure the IMA group. Click IMA > Group. Select Slot 2 and Port 3, then click Load. Configure the settings and note the following: • Do not select Enable since some settings (Group Symmetry and Frame Size) in the screen can be changed only when the group is disabled.
Page 87 Chapter 4 Tutorials Figure 35 Enable the IMA Group Example 7 Check the link status. Click Statistics > IMA, ID 2 (slot 2), port 3, group 2. In the Group Detail screen, you should see the values of the Ne State and Fe State fields are both operational.
Page 88 Chapter 4 Tutorials Similarly, click IMA > DTPVC, select Slot 2 and Group 2, then click Load. Create a DTPVC using VPI/VCI 0/34, Svid/Spri 100/0, Cvid/Cpri 20/0, MUX llc and Profile DEFVAL for the settings. Then click Apply. Figure 37 Creating a DTPVC Example Click IMA >...
Page 89: Changing The Default Management Pvc Vlan Id To Other Than 1 Or 0
Chapter 4 Tutorials 4.4 Changing the Default Management PVC VLAN ID to Other than 1 or 0 This tutorial assumes that you have done the configuration described in Section but you want to use a VLAN ID other than 1 or 0 for the management PVC settings (see Figure 38 on page 88).
Page 90 Chapter 4 Tutorials However, if traffic between IES-1 and M is untagged, make sure that you have the MSC of IES-1 remove VLAN 1000 from frames transmitted by Ethernet port 2 but add VLAN 1000 to frames received by Ethernet port 2. To configure this: Click VLAN >...
Page 91 Chapter 4 Tutorials After the settings above, you can configure an MGTPVC with PVID of 1000. To configure this: Click IMA > MGTPVC. Select the slot and IMA group (Slot 2 and Group 2 in this example) and click Load. Create an MGTPVC using VPI/VCI 0/35, PVID/Priority 1000/0, Profile DEFVAL and MUX llc for the settings.
Page 92 Chapter 4 Tutorials MSC1000G/1024G/1224G Series User’s Guide...
Page 93: Access Control List Screens
H A P T E R Access Control List Screens This chapter describes the ACL (Access Control List) screens. 5.1 DHCP Relay Overview DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a DHCP server. You can configure the system to relay client TCP/IP configuration requests to a DHCP server and the server's responses back to the clients.
Page 94: Format
Chapter 5 Access Control List Screens Port No field specifies the ingress port number (both in hexadecimal format). The next field is 2 bytes and displays the DHCP request packet’s VLAN ID. The last field (A) can range from 1 to 24 bytes (including a one-byte termination character) and is optional information (that you specify) about this relay agent.
Page 95: Pppoe Intermediate Agent
Chapter 5 Access Control List Screens TR-101 uses the same remote ID sub-option format as the Private format. 5.1.4 PPPoE Intermediate Agent You must use CLI commands to configure this feature. This section describes how the MSC gives a PPPoE termination server additional information that the server can use to identify and authenticate a PPPoE client.
Page 96: Dhcp Relay Screen
Chapter 5 Access Control List Screens 5.2 DHCP Relay Screen Figure 40 DHCP Relay The following table describes the labels in this screen. Table 14 DHCP Relay LABEL DESCRIPTION Enter a VLAN ID (between 1 and 4094) to be served with DHCP relay. Enable DHCP Select disable to deactivate the DHCP relay service in this VLAN.
Page 97: Example: Dhcp Relay For Two Vlans
Chapter 5 Access Control List Screens Table 14 DHCP Relay (continued) LABEL DESCRIPTION Primary/ Enter the IP addresses of the remote DHCP servers to which the switch should Secondary Server relay DHCP requests. Relay Mode Select Auto to have the system send DHCP requests to the active DHCP server first.
Page 98: Dhcp Snooping
Chapter 5 Access Control List Screens Figure 41 DHCP Relay Network Example DHCP: 192.168.1.100 Dorm (VID 10) Internet Academic (VID 12) DHCP: 192.168.10.100 For the example network, configure the DHCP Relay screen as shown. Figure 42 DHCP Relay: Configuration Example 5.3 DHCP Snooping With DHCP snooping, the system obtains a client’s MAC-IP address information (in the reply messages from a DHCP server) and stores it in the DHCP snooping table.
Page 99: Anti-Ip Address Spoofing
Chapter 5 Access Control List Screens You can also specify static IP addresses (for a subscriber given a static IP address) on a subscriber port. This is useful when service providers assign static WAN IP addresses to some subscribers. This static binding allows the switch to forward frames with the specified IP addresses.
Page 100 Chapter 5 Access Control List Screens Figure 44 DHCP Snooping The following table describes the labels in this screen. Table 15 DHCP Snooping LABEL DESCRIPTION Slot Use the drop-down list boxes to select a DSL port on a line card for which you want to configure DHCP snooping.
Page 101: Dhcp Snooping Slot Screen
Chapter 5 Access Control List Screens Table 15 DHCP Snooping (continued) LABEL DESCRIPTION Copy Do the following to copy the settings you configure above to another port or ports. 1. Click Copy. 2. Select to which line card you want to copy the settings. 3.
Page 102: Example: Dhcp Snooping
Chapter 5 Access Control List Screens Figure 45 DHCP Snooping: Slot The following table describes the labels in this screen. Table 16 DHCP Snooping: Slot LABEL DESCRIPTION Click UP to go back to the previous screen. Copy Do the following to copy settings from one port to another port or ports. 1.
Page 103: Downstream Broadcast Screen
Chapter 5 Access Control List Screens Figure 46 DHCP Snooping: Computer A Example Figure 47 DHCP Snooping: Computer B Example 5.5 Downstream Broadcast Screen Downstream broadcast allows you to block downstream broadcast packets from being sent to specified VLANs on specified ports. This helps to reduce downstream bandwidth requirements on a subscriber line.
Page 104 Chapter 5 Access Control List Screens Figure 48 Downstream Broadcast The following table describes the labels in this screen. Table 17 Downstream Broadcast LABEL DESCRIPTION Slot Use the drop-down list boxes to select an DSL port on an active line card for which you want to configure downstream broadcast blocking.
Page 105: Downstream Broadcast Slot Screen
Chapter 5 Access Control List Screens Table 17 Downstream Broadcast (continued) LABEL DESCRIPTION Copy Do the following to copy the settings you configure above to another port or ports. 1. Click Copy. 2. Select to which line card you want to copy the settings. 3.
Page 106: Mac Count Screen
Chapter 5 Access Control List Screens Figure 49 Downstream Broadcast: Slot The following table describes the labels in this screen. Table 18 Downstream Broadcast: Slot LABEL DESCRIPTION Click UP to go back to the previous screen. Copy Do the following to copy settings from one port to another port or ports. 1.
Page 107 Chapter 5 Access Control List Screens You cannot enable both MAC count and MAC filtering on the same port at the same time. Click ACL > MAC Count to display the screen shown next. Figure 50 MAC Count The following table describes the labels in this screen. Table 19 MAC Count LABEL DESCRIPTION...
Page 108: Mac Count Slot Screen
Chapter 5 Access Control List Screens Table 19 MAC Count (continued) LABEL DESCRIPTION Copy Do the following to copy the settings you configure above to another port or ports. 6. Click Copy. 7. Select to which line card you want to copy the settings. 8.
Page 109: Mac Filter Screen
Chapter 5 Access Control List Screens Figure 51 MAC Count: Slot The following table describes the labels in this screen. Table 20 MAC Count: Slot LABEL DESCRIPTION Click UP to go back to the previous screen. Copy Do the following to copy settings from one port to another port or ports. 1.
Page 110 Chapter 5 Access Control List Screens You cannot enable both MAC filtering and MAC count on the same port at the same time. You cannot enable both MAC filtering and OUI filtering at the same time. Click ACL > MAC Filter to display the screen shown next. Figure 52 MAC Filter The following table describes the labels in this screen.
Page 111: Mac Filter Slot Screen
Chapter 5 Access Control List Screens Table 21 MAC Filter (continued) LABEL DESCRIPTION Mode Select accept to only allow frames from MAC addresses that you specify and block frames from other MAC addresses. Select deny to block frames from MAC addresses that you specify and allow frames from other MAC addresses.
Page 112: Oui Filter
Chapter 5 Access Control List Screens Table 22 MAC Filter: Slot (continued) LABEL DESCRIPTION Enable This field displays whether MAC filtering is activated on the specified DSL port or not (V for enabled, - for disabled). This fields displays the MAC address(es) you set for the port. 5.8 OUI Filter Configure an OUI (Organizationally Unique Identifier) filter to block or forward packets from devices with the specified OUI in the MAC address.
Page 113 Chapter 5 Access Control List Screens The following table describes the labels in this screen. Table 23 OUI Filter LABEL DESCRIPTION Slot Use the drop-down list boxes to select an DSL port on a line card for which you wish to configure packet type filtering.
Page 114: Oui Filter Slot Screen
Chapter 5 Access Control List Screens Table 23 OUI Filter (continued) LABEL DESCRIPTION Card Type This field displays the type of a line card. Up Time This field displays how long the line card has been running since the last time it was started.
Page 115: Packet Filter Screen
Chapter 5 Access Control List Screens Table 24 OUI Filter: Slot (continued) LABEL DESCRIPTION Mode This field displays the filter mode (deny or accept). Enable This field displays whether OUI filtering is activated on the specified DSL port or not (V for enabled, - for disabled). This field displays the OUI address to filter on a port.
Page 116 Chapter 5 Access Control List Screens Table 25 Packet Filter (continued) LABEL DESCRIPTION PPPoE Only Select PPPoE Only to allow only PPPoE traffic. This will gray out the check boxes for other packet types and the switch will drop any non-PPPoE packets. Custom Select Custom and specify which types of packets listed below will be blocked.
Page 117: Packet Filter Slot Screen
Chapter 5 Access Control List Screens Table 25 Packet Filter (continued) LABEL DESCRIPTION State This field displays the line card’s current operational status. active means the line card is operating normally. init means the MSC is initializing the line card. disable means a manager has disabled the line card.
Page 118: Ieee 802.1X
Chapter 5 Access Control List Screens The following table describes the labels in this screen. Table 26 Packet Filter: Slot LABEL DESCRIPTION Click UP to go back to the previous screen. Copy Do the following to copy settings from one port to another port or ports. 1.
Page 119: Radius
Chapter 5 Access Control List Screens 5.11.1 RADIUS RADIUS authentication is a popular protocol used to authenticate users by means of an external server instead of (or in addition to) an internal device user database that is limited to the memory capacity of the device. In essence, RADIUS authentication allows you to validate an unlimited number of users from a central location.
Page 120 Chapter 5 Access Control List Screens Figure 59 802.1X PNAC: Port Setup The following table describes the labels in this screen. Table 27 802.1X PNAC: Port Setup LABEL DESCRIPTION Slot Use the drop-down list boxes to select an DSL port on a line card for which you wish to configure IEEE 802.1x authentication.
Page 121: Pnac Slot Screen
Chapter 5 Access Control List Screens Table 27 802.1X PNAC: Port Setup (continued) LABEL DESCRIPTION Copy Do the following to copy the settings you configure above to another port or ports. 1. Click Copy. 2. Select to which line card you want to copy the settings. 3.
Page 122: Radius Screen
Chapter 5 Access Control List Screens Figure 60 802.1X PNAC: Port Setup: Slot The following table describes the labels in this screen. Table 28 802.1X PNAC: Port Setup: Slot label description Click UP to go back to the previous screen. Copy Do the following to copy settings from one port to another port or ports.
Page 123: Upstream Broadcast Control Screen
Chapter 5 Access Control List Screens Figure 61 802.1X PNAC: RADIUS The following table describes the labels in this screen. Table 29 802.1X PNAC: RADIUS LABEL DESCRIPTION Enable Select this check box to have the switch use an external RADIUS server to authenticate users.
Page 124: Acl Rule Screen
Chapter 5 Access Control List Screens Figure 62 ACL > Upstream Broadcast The following table describes the labels in this screen. Table 30 ACL > Upstream Broadcast LABEL DESCRIPTION Enable Click this to enable bandwidth control for upstream broadcast traffic. Rate Enter the maximum bandwidth for upstream broadcast traffic (in Kbps) allowed to flow into the line card from a subscriber line.
Page 125: Anti-Mac Spoofing Screen
Chapter 5 Access Control List Screens The following table describes the labels in this screen. Table 31 ACL > Rule LABEL DESCRIPTION Slot Use the drop-down list boxes to select a DSL line card and port for which to apply ACL profiles to a PVC.
Page 126: Dscp Screens
Chapter 5 Access Control List Screens Figure 64 ACL > AntiMacspoof The following table describes the labels in this screen. Table 32 ACL > AntiMacspoof LABEL DESCRIPTION Enable Turn on anti-MAC spoofing to have the system check for hosts with fake or duplicated MAC addresses which attempt to access the system.
Page 127: Dscp Port Screen
Chapter 5 Access Control List Screens Figure 65 ACL > DSCP > Setup The following table describes the labels in this screen. Table 33 ACL > DSCP > Setup LABEL DESCRIPTION DSCP mapping Use the drop-down list boxes to select an IEEE 802.1p priority to which the Device (priority) should change the DSCP service level.
Page 128 Chapter 5 Access Control List Screens Figure 66 ACL > DSCP > Port The following table describes the labels in this screen. Table 34 ACL > DSCP > Port LABEL DESCRIPTION Slot Use the drop-down list boxes to select a line card and port. Port Load Click Load to display the port’s current settings.
Page 129: Dscp Port Slot Screen
Chapter 5 Access Control List Screens Table 34 ACL > DSCP > Port (continued) LABEL DESCRIPTION Copy Do the following to copy the settings you configure above to another port or ports. 1. Click Copy. 2. Select the line card to which you want to copy the settings. 3.
Page 130: Pppoe Screen
Chapter 5 Access Control List Screens Figure 67 DSCP > Port: Slot The following table describes the labels in this screen. Table 35 DSCP > Port: Slot LABEL DESCRIPTION Click UP to go back to the previous screen. Copy Do the following to copy settings from one port to another port or ports. 1.
Page 131 Chapter 5 Access Control List Screens Figure 68 ACL > PPPoE The following table describes the labels in this screen. Table 36 ACL > PPPoE LABEL DESCRIPTION Enter a VLAN ID (between 1 and 4094). Enable Turns PPPoE line information for the VLAN on or off. Option Mode Select private to use ZyXEL’s proprietary method to encode PPPoE discover packets on the specified VLAN.
Page 132: Loop Guard
Chapter 5 Access Control List Screens 5.19 Loop Guard Configure loop guard to protect against loops on the edge of your network. Loop guard allows you to configure the system to shut down a port if it detects that packets sent out on that port loop back to the system.
Page 133 Chapter 5 Access Control List Screens The loop guard feature checks to see if a loop guard enabled port is connected to a switch in loop state. This is accomplished by periodically sending a probe packet and seeing if the packet returns on the same port.
Page 134: Loop Guard Setup
Chapter 5 Access Control List Screens 5.20 Loop Guard Setup Click ACL > Loop Guard in the navigation panel to display the screen as shown. The loop guard feature cannot be enabled on ports that have Spanning Tree Protocol (RSTP or MSTP) enabled. Figure 73 ACL >...
Page 135 Chapter 5 Access Control List Screens Table 37 ACL > Loop Guard (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this part of the screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 136: Loop Guard Slot Screen
Chapter 5 Access Control List Screens Table 37 ACL > Loop Guard (continued) LABEL DESCRIPTION Up Time This field displays how long the line card has been running since the last time it was started. Firmware This field displays the current firmware version installed on the line card. 5.20.1 Loop Guard Slot Screen Click the slot number of an active line card in the ACL >...
Page 137: Subnet Based Vlans
Chapter 5 Access Control List Screens Table 38 ACL > Loop Guard: Slot (continued) LABEL DESCRIPTION Time This field displays the time (in seconds) a port in dynamic mode waits to become active again after shut down by the system. Select Select the radio button of the port from which you want to copy settings.
Page 138 Chapter 5 Access Control List Screens Subnet based VLAN applies to un-tagged packets and is applicable only when you use IEEE 802.1Q tagged VLAN. Figure 76 ACL > Subnet VLAN The following table describes the labels in this screen. Table 39 ACL > Subnet VLAN LABEL DESCRIPTION Enable...
Page 139: Upstream Broadcast Storm Control
Chapter 5 Access Control List Screens Table 39 ACL > Subnet VLAN (continued) LABEL DESCRIPTION This field shows the VLAN ID of the frames which belong to this subnet based VLAN. Priority This field shows the priority which is assigned to frames belonging to this subnet based VLAN.
Page 140 Chapter 5 Access Control List Screens Table 40 ACL > Upstream Storm (continued) LABEL DESCRIPTION Broadcast Select Disable to not limit the number of broadcast packets the interface will accept per second. Type how many broadcast packets the interface should accept per second. Multicast Select Disable to not limit the number of multicast packets the interface will accept per second.
Page 141: Upstream Storm Slot Screen
Chapter 5 Access Control List Screens Table 40 ACL > Upstream Storm (continued) LABEL DESCRIPTION Up Time This field displays how long the line card has been running since the last time it was started. Firmware This field displays the current firmware version installed on the line card. 5.23.1 Upstream Storm Slot Screen Click the slot number of an active line card in the ACL >...
Page 142 Chapter 5 Access Control List Screens MSC1000G/1024G/1224G Series User’s Guide...
Page 143: Alarm Screens
H A P T E R Alarm Screens This chapter describes alarm management. 6.1 Current Alarm Screen Click Alarm > Current Alarm to display the screen where you can view all current alarms. You can also click a tab to view the alarms only specific to one severity level. Figure 79 Current Alarm: All The following table describes the labels in this screen.
Page 144: History Alarm Screen
Chapter 6 Alarm Screens Table 42 Current Alarm: All (continued) LABEL DESCRIPTION Previous Click Previous or Next to show the preceding/following screen if the information cannot be displayed in one screen. Next Next 10 Click Next 10 to show the following 10 pages of alarms. 6.2 History Alarm Screen Click Alarm >...
Page 145: Alarm Port Setup Screen
Chapter 6 Alarm Screens Table 43 History Alarm: All (continued) LABEL DESCRIPTION Source This is the location where the alarm occurred. Previous 10 Click Previous 10 to show the preceding 10 alarms. Previous Click Previous or Next to show the preceding/following screen if the information cannot be displayed in one screen.
Page 146 Chapter 6 Alarm Screens The following table describes the labels in this screen. Table 44 Alarm Port Setup LABEL DESCRIPTION sub1 Select the severity level from info, minor, major and critical for the alarms to record on the specified port of the MSC. sub2 Management Apply...
Page 147: Alarm Port Setup Slot Screen
Chapter 6 Alarm Screens Table 44 Alarm Port Setup (continued) LABEL DESCRIPTION State This field displays the line card’s current operational status. active means the line card is operating normally. init means the MSC is initializing the line card. disable means a manager has disabled the line card. inactive means the line card is starting up or is not operating normally.
Page 148: Alarm Severity Assignment Screen
Chapter 6 Alarm Screens The following table describes the labels in this screen. Table 45 Alarm Port Setup: Slot LABEL DESCRIPTION Click UP to go back to the previous screen. Copy Do the following to copy settings from one port to another port or ports. 1.
Page 149 Chapter 6 Alarm Screens Figure 83 Alarm Severity Assignment: DSL The following table describes the labels in this screen. Table 46 Alarm Severity Assignment: DSL LABEL DESCRIPTION Condition This identifies an individual alarm. See Section 6.5 on page 150 for more information.
Page 150: Alarm Descriptions
Chapter 6 Alarm Screens 6.5 Alarm Descriptions This table describes the alarms on the system. You can view the settings using the “alarm tablelist” CLI command. • “ALC” is the ADSL Line Card. • “SLC” is the SHDSL Line Card. •...
Page 151 Chapter 6 Alarm Screens Table 47 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION ADSL_TCA_ES INFO The Error Seconds (<value>) within 15 minutes for the atu(c or r) has reached the threshold (<value>). ADSL_RATE_CHANGE INFO The transmission rate of the atu(c or r) changed from <value>...
Page 152 Chapter 6 Alarm Screens Table 47 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION VDSL_TCA_LOL INFO The Loss Of Link seconds (<value>) within 15 minutes for the vtu(c or r) has reached the threshold (<value>). VDSL_TCA_LOF INFO The Loss Of Frame seconds (<value>) within 15 minutes for...
Page 153 Chapter 6 Alarm Screens Table 47 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION DC_POWER_FAIL CRITICAL The -48VDC power -<index> failed. VOLTAGE_ERROR CRITICAL The voltage <index> at input <value> is too low <value>, or high <value>. TEMPERATURE_ERROR CRITICAL The temperature <index>...
Page 154 Chapter 6 Alarm Screens Table 47 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION CPU_UTIL_HIGH MAJOR The MSC is overloading. VOP_BATTERY_FAIL CRITICAL A VOP card’s battery failed. VOP_CLOCK_FAIL CRITICAL A VOP card’s clock failed. VOP_RINGER_FAULT CRITICAL A VOP card’s ringer failed.
Page 155 Chapter 6 Alarm Screens Table 47 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION CLUSTER_MBR_INACTIV INFO The cluster manager has established a connection with a particular cluster member. CLUSTER_MBR_ADD INFO The cluster manager added a member to a cluster. CLUSTER_MBR_DELETE INFO The cluster manager removed a...
Page 156 Chapter 6 Alarm Screens Table 47 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION VOP_MC_MISSING CRITICAL The signaling VOP card cannot detect the media VOP card. VOP_SC_MISSING CRITICAL The media VOP card cannot detect the signaling VOP card. VOP_TERMNAME_DUP INFO The VOP detected a duplicate...
Page 157 Chapter 6 Alarm Screens Table 47 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION LINK_TX_MIS_CONN minor A transmit link is not connected to the same remote IMA device as the other transmit links in the group. LINK_RX_MIS_CONN minor A receiving link is not connected...
Page 158 Chapter 6 Alarm Screens Table 47 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION DS1_15MIN_UAS_TCA minor The UnAvailable Seconds within the current 15 minutes on the E1 line has reached the threshold. DS1_24HR_ES_TCA minor The Error Seconds within the last 24 hours on the E1 line has reached the threshold.
Page 159 Chapter 6 Alarm Screens Table 48 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION ADSL_RATE_CHANGE INFO The transmission rate of the atu(c or r) changed from <value> to <value>. ADSL_TCA_SES INFO The Severely Errored Seconds (<value>) within 15 minutes for the atu(c or r) has reached the threshold (<value>).
Page 160 Chapter 6 Alarm Screens Table 48 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION VDSL_TCA_LOF INFO The Loss Of Frame seconds (<value>) within 15 minutes for the vtu(c or r) has reached the threshold (<value>). VDSL_TCA_LOS INFO The Loss Of Signal seconds (<value>) within 15 minutes for...
Page 161 Chapter 6 Alarm Screens Table 48 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION VOLTAGE_ERROR CRITICAL The voltage <index> at input <value> is too low <value>, or high <value>. TEMPERATURE_ERROR CRITICAL The temperature <index> at input <value> is too low <value> or high <value>.
Page 162 Chapter 6 Alarm Screens Table 48 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION VOP_CLOCK_FAIL CRITICAL A VOP card’s clock failed. VOP_RINGER_FAULT CRITICAL A VOP card’s ringer failed. PKTBUFF_LOW MAJOR The buffer storage for packet transmission is too low. This might cause some incoming packets to be dropped.
Page 163 Chapter 6 Alarm Screens Table 48 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION CLUSTER_MBR_ADD INFO The cluster manager added a member to a cluster. CLUSTER_MBR_DELETE INFO The cluster manager removed a member from cluster. PING_PROBE_FAIL INFO A continuous ping test via diagnostic tool is failed.
Page 164 Chapter 6 Alarm Screens Table 48 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION VOP_SC_MISSING CRITICAL The media VOP card cannot detect the signaling VOP card. VOP_TERMNAME_DUP INFO The VOP detected a duplicate terminal name. VOP_NO_PROTECTION INFO The active SC cannot detect the standby SC.
Page 165 Chapter 6 Alarm Screens Table 48 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION LINK_RX_MIS_CONN minor A receiving link is not connected to the same remote IMA device as the other receiving links in the group. LINK_TX_FAULT minor The transmit link is in the FAULT...
Page 166: Alarm Clear Screen
Chapter 6 Alarm Screens Table 48 Alarm Descriptions (continued) ALARM SEVERITY MSC ALC SLC VLC VOP IMA DESCRIPTION DS1_24HR_ES_TCA minor The Error Seconds within the last 24 hours on the E1 line has reached the threshold. DS1_24HR_SES_TCA minor The Severely Errored Seconds within the last 24 hours on the E1 line has reached the threshold.
Page 167 Chapter 6 Alarm Screens Figure 85 Alarm > Alarm Input The following table describes the labels in this screen. Table 50 Alarm > Alarm Input LABEL DESCRIPTION Index This is the index number for the external alarm input. Input Enter 1 to 31 characters for the name of the connected external alarm system. Apply Click Apply to save the changes in this screen to the system’s volatile memory.
Page 168 Chapter 6 Alarm Screens MSC1000G/1024G/1224G Series User’s Guide...
Page 169: Cluster Screens
H A P T E R Cluster Screens This chapter covers how to configure cluster management. 7.1 Cluster Management Status Overview Cluster management allows you to manage multiple DSLAMs through one DSLAM, called the cluster manager. The DSLAMs must be directly connected and be in the same VLAN group so as to be able to communicate with one another.
Page 170: Cluster Management Status
Chapter 7 Cluster Screens 7.2 Cluster Management Status Click Cluster in the navigation panel to display the following screen. A cluster can only have one manager. Figure 87 Cluster: Status The following table describes the labels in this screen. Table 52 Cluster: Status LABEL DESCRIPTION Number of...
Page 171: Cluster Management Configuration
Chapter 7 Cluster Screens 7.3 Cluster Management Configuration Use this screen to configure cluster management settings. Click Cluster > Configuration to display the next screen. Figure 88 Cluster: Configuration MSC1000G/1024G/1224G Series User’s Guide...
Page 172 Chapter 7 Cluster Screens The following table describes the labels in this screen. Table 53 Cluster: Configuration LABEL DESCRIPTION Cluster Manager Activity Select Disabled to have this DSLAM not function as part of the cluster. Select Manager to have this DSLAM become the cluster manager DSLAM. A cluster can only have one manager.
Page 173: Cluster Member Management
Chapter 7 Cluster Screens Table 53 Cluster: Configuration (continued) LABEL DESCRIPTION Select Select this check box and then configure the Password and the Member ID fields and click the Apply button to add a cluster member candidate to the cluster. Password Each cluster member’s password is its management password.
Page 174 Chapter 7 Cluster Screens The following table describes the labels at the top of the screen. Table 54 Cluster Member Web Configurator Screen LABEL DESCRIPTION Cluster Name This is the name of the cluster. Cluster ID This is the VLAN ID that the cluster uses and is only applicable if the manager DSLAM is set to use IEEE 802.1Q VLAN.
Page 175: Diagnostic Screens
H A P T E R Diagnostic Screens This chapter explains the Diagnostic screens. 8.1 CFM Overview The route between a CO network and one of a CPE user may go through aggregated switches, routers and/or DSLAMs owned by independent organizations. A connectivity fault point generally takes time to discover and impacts on subscribers’...
Page 176: Ldm Test Screen (Delt)
Chapter 8 Diagnostic Screens • MEP port - has the ability to send pro-active connectivity check (CC) packets and get other MEP ports information from the CC packets of neighboring switches within an • MIP port - only forwards the CC packets. CFM provides two tests to discover connectivity faults.
Page 177 Chapter 8 Diagnostic Screens Figure 92 LDM Test The following table describes the labels in this screen. Table 55 LDM Test LABEL DESCRIPTION LDM Test Select slot and port numbers from the Slot and Port drop-down list boxes and click Set LDM Port to perform loop diagnostics on the specified port. Only slots with an active ADSL line card display in the Slot drop-down list box.
Page 178: Loop Diagnostics Test Parameters
Chapter 8 Diagnostic Screens 8.2.1 Loop Diagnostics Test Parameters The following table lists the loop diagnostics test parameters that display, see the ITU-T’s G.992.3 for more information. Table 56 Loop Diagnostics Test Parameters LABEL DESCRIPTION near end This column of diagnostics results is for the upstream traffic (coming from the subscriber to the IES).
Page 179: Ip Ping Screen
Chapter 8 Diagnostic Screens Figure 93 Loopback The following table describes the labels in this screen. Table 57 Loopback LABEL DESCRIPTION Loopback Select slot and port numbers from the Slot and Port drop-down list boxes. In the Item drop-down list box, select the type of loopback test. Currently oam f5 loopback test is supported.
Page 180: Trace Route Screen
Chapter 8 Diagnostic Screens The following table describes the labels in this screen. Table 58 IP Ping LABEL DESCRIPTION IP Ping Type the IP address of a device that you want to ping in order to test a connection. In the field to the right specify the number of times that you want to ping the IP address. Click Ping to ping the IP address that you specified.
Page 181 Chapter 8 Diagnostic Screens Figure 96 Diagnostic > MLT Screen The following table describes the labels in this screen. Table 60 Diagnostic > MLT Screen LABEL DESCRIPTION Use the Slot and Port drop-down list boxes to select the port on an active VoIP line card you want to configure.
Page 182: Cfm Loopback Screen
Chapter 8 Diagnostic Screens Table 60 Diagnostic > MLT Screen LABEL DESCRIPTION Forced Select this to perform the test(s) immediately, even if the specified port is in use. Perform all the MLT tests. AC Voltage Test the line’s AC voltage. DC Voltage Test the line’s DC voltage.
Page 183: Cfm Linktrace Screen
Chapter 8 Diagnostic Screens The following table describes the labels in this screen. Table 61 CFM Loopback LABEL DESCRIPTION Select an MD name. If the drop-down list is empty, create an MD in the Switch > CFM screen. Select an MA name under the selected MD. If the drop-down list is empty, create an MA in the Switch >...
Page 184: Selt Test Screen
Chapter 8 Diagnostic Screens Table 62 Diagnostic > CFM Linktrace (continued) LABEL DESCRIPTION MEPID Select an MEP ID to specify which MEP port on the device initiates the test. If the drop-down list is empty, create an MA in the Switch > CFM > CFM maintenance association >...
Page 185: Oam Loopback Screen
Chapter 8 Diagnostic Screens The following table describes the labels in this screen. Table 63 Diagnostic > SELT LABEL DESCRIPTION SELT Test Select slot and port numbers from the Slot (not all cards support the SELT test) and Port drop-down list boxes and click Set SELT Port to perform a Single End Loop Test (SELT) on the specified port.
Page 186 Chapter 8 Diagnostic Screens Figure 101 IMA Loopback The following table describes the labels in this screen. Table 65 IMA Loopback LABEL DESCRIPTION Select the slot of an IMA line card from the Slot drop-down list box and a test item (E1, Loopback IMA, F5 end2end or F5 segment).
Page 187 Chapter 8 Diagnostic Screens Table 65 IMA Loopback (continued) LABEL DESCRIPTION F5 end2end Select this to perform an ATM F5 end to end loopback test. Group: Select the number of an IMA group. VPI/VCI: Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) of a channel in this group.
Page 188 Chapter 8 Diagnostic Screens MSC1000G/1024G/1224G Series User’s Guide...
Page 189: Maintenance Screens
H A P T E R Maintenance Screens This chapter explains how to use the maintenance screens. 9.1 Configuration Backup Screen Click Maintenance > Config Backup in the navigation panel to open the following screen. Use this screen to back up your system configuration. This allows you to create various “snap shots”...
Page 190: Configuration Reset Screen
Chapter 9 Maintenance Screens Figure 103 Configuration Restore Type the path and file name of the configuration file you wish to restore in the File Path text box or click Browse to display a Choose File screen from which you can locate it. After you have specified the file, click Restore.
Page 191: Firmware Upgrade Screen
Chapter 9 Maintenance Screens Figure 106 Restart After Load Factory Defaults 9.4 Firmware Upgrade Screen Click Maintenance > Firmware Upgrade in the navigation panel to open the following screen. Use this screen to view your current firmware version number and upload firmware to cards in the system.
Page 192: Reboot Screen
Chapter 9 Maintenance Screens Type the path and file name of the firmware file you wish to upload in the File Path text box or click Browse to locate it. After you have specified the file, click Upgrade. After the firmware upgrade process is complete, use this screen to verify your current firmware version number.
Page 193: Multicast Screens
H A P T E R Multicast Screens This chapter describes the Multicast screens. 10.1 IGMP Introduction Traditionally, IP packets are transmitted in one of either two ways - Unicast (1 sender to 1 recipient) or Broadcast (1 sender to everybody on the network). Multicast delivers IP packets to just a group of hosts on the network.
Page 194: Igmp Snooping And Proxy Note
Chapter 10 Multicast Screens In IGMP proxy, an upstream interface is the port that is closer to the source (or the root of the multicast tree) and is able to receive multicast traffic. There should only be one upstream interface (also known as the query port) on the system to limit bandwidth use. A downstream interface is a port that connects to a host (such as a computer).
Page 195: Igmp Fast Leave
Chapter 10 Multicast Screens 10.1.5 IGMP Fast Leave When a host leaves a multicast group (224.1.1.1), it sends an IGMP leave message to inform all routers (224.0.0.2) in the multicast group. When a router receives the leave message, it sends a specific query message to all multicast group (224.1.1.1) members to check if any other hosts are still in the group.
Page 196: Igmp Filtering
Chapter 10 Multicast Screens The following table describes the labels in this screen. Table 66 IGMP Setup LABEL DESCRIPTION IGMP Mode Select Enable_IGMP_Snooping to have the system passively learn multicast groups. Select Enable_IGMP_Proxy to have the system proxy multicast traffic. Select Disable to have the system not use either IGMP proxy or snooping.
Page 197 Chapter 10 Multicast Screens Figure 113 Multicast > IGMP > Port Setup The following table describes the labels in this screen. Table 67 IGMP Port Setup LABEL DESCRIPTION Slot Select the number of a line card’s slot. Port Select the number of a DSL port on the line card. Load Click Load to retrieve the port’s IGMP filter profile setting and display it in the Profile drop-down list box.
Page 198: Igmp Bandwidth Screen
Chapter 10 Multicast Screens Table 67 IGMP Port Setup (continued) LABEL DESCRIPTION Copy Do the following to copy IGMP port settings from one DSL port to another DSL port or ports. 1. Select the radio button of the DSL port from which you want to copy IGMP filter profile settings.
Page 199 Chapter 10 Multicast Screens Figure 115 Multicast > IGMP > Bandwidth The following table describes the labels in this screen. Table 68 Multicast > IGMP > Bandwidth LABEL DESCRIPTION Default Select the maximum bandwidth allowed for multicast traffic for which you have not Bandwidth configured bandwidth requirements yet.
Page 200: Static Multicast Screen
Chapter 10 Multicast Screens 10.4 Static Multicast Screen Click Multicast > Static Multicast in the navigation panel to display the screen shown next. Use static multicast to allow incoming frames based on the VID and multicast MAC address(es). This feature can be used in conjunction with IGMP snooping to allow multicast MAC address(es) that are not learned by IGMP snooping or IGMP proxy and would otherwise be dropped.
Page 201: Static Multicast Slot Screen
Chapter 10 Multicast Screens Table 69 Static Multicast (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non- volatile memory when you are done configuring.
Page 202: Static Mac Multicast Screen
Chapter 10 Multicast Screens The following table describes the related labels in this screen. Table 70 Static Multicast Slot LABEL DESCRIPTION The numbers represent the individual ports on the card. Use the F, -, and X radio buttons to set each port’s membership in the static multicast group.
Page 203 Chapter 10 Multicast Screens Figure 118 Static MAC Multicast The following table describes the related labels in this screen. Table 71 Static MAC Multicast LABEL DESCRIPTION Type the number of the VLAN that incoming packets for this static multicast group must be tagged with.
Page 204: Static Mac Multicast Slot Screen
Chapter 10 Multicast Screens Table 71 Static MAC Multicast (continued) LABEL DESCRIPTION Port This section lists the VLAN membership setting of the ports on the management switch card. An “F” indicates that the port is a permanent member of the static multicast group.
Page 205: Mvlan Setup Screen
Chapter 10 Multicast Screens Table 72 Static MAC Multicast Slot (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non- volatile memory when you are done configuring.
Page 206: Mvlan Port Setting Screen
Chapter 10 Multicast Screens Table 73 MVLAN Setup (continued) LABEL DESCRIPTION Cardname This field displays the model of the installed card. Port This section shows each port’s membership in the MVLAN. F: The port is a permanent member of the MVLAN. X: The port is prohibited from joining the MVLAN.
Page 207: Mvlan Group Setup Screen
Chapter 10 Multicast Screens The following table describes the labels in this screen. Table 74 MVLAN Port Setting LABEL DESCRIPTION The numbers represent the individual ports on the card. Use the F, -, and X radio buttons to set each port’s membership in the MVLAN. Select F to make the port a permanent member of the MVLAN.
Page 208 Chapter 10 Multicast Screens Table 75 MVLAN Group Setup (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non- volatile memory when you are done configuring.
Page 209: Subscriber Port Setup Screens
H A P T E R Subscriber Port Setup Screens This chapter explains how to configure settings for individual subscriber ports. It also covers how to configure permanent virtual circuits. 11.1 ADSL Standards Overview These are the ADSL standards and rates that the ADSL line card supports at the time of writing.
Page 210: Frequency Band Plan
Chapter 11 Subscriber Port Setup Screens 11.2.3 Frequency Band Plan Each VDSL mode operates in a different frequency band allocation, resulting in different upstream and downstream speeds. Your system automatically changes the band plan based on the loop condition and loop length. A band plan example is shown next.
Page 211: Configured Versus Actual Rate
Chapter 11 Subscriber Port Setup Screens 11.2.5 Configured Versus Actual Rate You configure the maximum rate of an individual VDSL port by modifying its profile (see the VDSL Profile Setup screen) or assigning the port to a different profile (see the Port Setup screen).
Page 212: Dpbo
Chapter 11 Subscriber Port Setup Screens 11.2.8 DPBO VDSL signals may interfere with other services (such as ISDN, ADSL or ADSL2 provided by other devices) on the same bundle of lines due to downstream far-end crosstalk. DPBO (Downstream Power Back Off) can reduce performance degradation by changing the PSD level on the VDSL switch(es) at street cabinet level.
Page 213: Rate Adaption
Chapter 11 Subscriber Port Setup Screens The following table displays the calculation from a real length to an electrical length. Table 79 Real Length to Electrical Length CABLE TYPE REAL LENGTH TO ELECTRICAL LENGTH 22 AWG =16.2*(cable length in kilometer) 24 AWG =20.5*(cable length in kilometer) 26 AWG...
Page 214: Alarm Profiles
Chapter 11 Subscriber Port Setup Screens For example, you could set up different profiles for different kinds of accounts (for example, economy, standard and premium). Assign the appropriate profile to an DSL port and it takes care of a large part of the port’s configuration. You still get to individually enable or disable each port and configure port specific settings.
Page 215 Chapter 11 Subscriber Port Setup Screens Figure 126 ADSL Port Setup The following table describes the fields in this screen. Table 80 ADSL Port Setup LABEL DESCRIPTION Slot Select the number of a line card’s slot. The corresponding subscriber port setup screen for the type of line card you selected automatically displays.
Page 216 Chapter 11 Subscriber Port Setup Screens Table 80 ADSL Port Setup (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 217: Adsl Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens 11.7.1 ADSL Port Setup Line Card Screen Click Port > ADSL in the navigation panel to open the ADSL Port Setup screen. Click the slot number of an active ADSL line card to open the following screen. Use this screen to configure settings for individual ADSL ports and copy settings between ports.
Page 218: Adsl Port Setup Advanced
Chapter 11 Subscriber Port Setup Screens Table 81 ADSL Port Setup: Line Card (continued) LABEL DESCRIPTION Port These are the numbers of the DSL ports on the line card. To configure advanced port settings, click a port number to display the ADSL Port Setup screen.
Page 219 Chapter 11 Subscriber Port Setup Screens Figure 130 ADSL Port Setup: Advanced The following table describes the fields in this screen. Table 82 ADSL Port Setup: Advanced LABEL DESCRIPTION Click this to return to the previous screen. Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 220 Chapter 11 Subscriber Port Setup Screens Table 82 ADSL Port Setup: Advanced (continued) LABEL DESCRIPTION ADSL Profile Select a profile of ADSL settings (such as the transfer rate, interleave delay and signal to noise ratio settings) to assign to this port. Use the ADSL Profile screen to configure ADSL port profiles.
Page 221 Chapter 11 Subscriber Port Setup Screens Table 82 ADSL Port Setup: Advanced (continued) LABEL DESCRIPTION Power Mode The power mode controls the connection’s power adaptivity. Select fix to set the maximum downstream transmit power to the number you specify in the Max DS TxPower field. Select power to give the saving of transmission power priority over the transmission rate.
Page 222: Adsl Option Mask Screen
Chapter 11 Subscriber Port Setup Screens Table 82 ADSL Port Setup: Advanced (continued) LABEL DESCRIPTION DS Carrier Use these fields to disable downstream carrier tones (from 32~255). (32~255) Mask1 = tones 32~63 Mask2 = tones 64~95 Mask3 = tones 96~127 Mask4 = tones 128~159 Mask5 = tones 160~191 Mask6 = tones 192~223...
Page 223 Chapter 11 Subscriber Port Setup Screens Figure 131 ADSL Port Setup: Advanced: Option Mask The following table describes the fields in this screen. Table 83 ADSL Port Setup: Advanced: Option Mask LABEL DESCRIPTION Use the check boxes to disable individual features. Use the All check box to select every feature check box.
Page 224: Vdsl Port Setup
Chapter 11 Subscriber Port Setup Screens 11.8 VDSL Port Setup Click Port > VDSL in the navigation panel to open the following screen. Use this screen to configure settings for individual VDSL ports on VLCs that follow the VDSL1 MIB as defined in ADSL Extension Line MIB (RFC 3440).
Page 225 Chapter 11 Subscriber Port Setup Screens Table 84 VDSL Port Setup (continued) LABEL DESCRIPTION Alarm Profile Select an alarm profile to define the thresholds that trigger an alarm on the port when exceeded. Customer Enter information to identify the subscriber connected to this DSL port. You can Information use up to 31 printable English keyboard characters (including spaces and hyphens).
Page 226: Vdsl Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens Table 84 VDSL Port Setup (continued) LABEL DESCRIPTION State This field displays the line card’s current operational status. active means the line card is operating normally. init means the MSC is initializing the line card. disable means a manager has disabled the line card.
Page 227: Vdsl Port Setup Advanced
Chapter 11 Subscriber Port Setup Screens The following table describes the fields in this screen. Table 85 VDSL Port Setup: Line Card LABEL DESCRIPTION Click this to return to the previous screen. Copy Do the following to copy settings from one DSL port to another DSL port or ports. 1.
Page 228 Chapter 11 Subscriber Port Setup Screens Figure 136 VDSL Port Setup: Advanced The following table describes the fields in this screen. Table 86 VDSL Port Setup: Advanced LABEL DESCRIPTION Click this to return to the previous screen. Customer Info Enter information to identify the subscriber connected to this VDSL port. You can use up to 31 printable English keyboard characters (including spaces and hyphens).
Page 229 Chapter 11 Subscriber Port Setup Screens Table 86 VDSL Port Setup: Advanced LABEL DESCRIPTION Enter information to identify the telephone number of the subscriber connected to this VDSL port. You can use up to 15 English keyboard characters (including spaces and hyphens). VDSL Profile Select a VDSL line profile to assign to this port in the first drop-down list box.
Page 230 Chapter 11 Subscriber Port Setup Screens Table 86 VDSL Port Setup: Advanced LABEL DESCRIPTION UPBO UPBO (Upstream Power Back Off) allows the switch to provide better service in a network environment with telephone wiring of varying lengths. Select Enable to activate this feature. Select Disable to deactivate this feature.
Page 231: The Vdsl Port Setup Screen (Ctd.)
Chapter 11 Subscriber Port Setup Screens Table 86 VDSL Port Setup: Advanced LABEL DESCRIPTION Result Mask Click Show to display the upstream and downstream result mask. Use this screen to check PSD mask settings. Figure 137 Result Mask Click Close Window to close this window. ADSL The VDSL2 frequency band overlaps with the ADSL2 and ADSL2s frequency spectrum...
Page 232 Chapter 11 Subscriber Port Setup Screens Figure 138 VDSL Port Setup: Advanced (ctd.) The following table describes the fields in this screen. Table 87 VDSL Port Setup: Advanced LABEL DESCRIPTION Index This field displays the index number. Enable Select Enable to activate the RFI band. Start Enter the start of the frequency range in kilohertz (kHz).
Page 233: Vdsl Optionmask Screen
Chapter 11 Subscriber Port Setup Screens 11.8.3.1 Limit Mask Profiles The following section describes the limit mask profiles supported by your Device. Select a limit mask profile for use on your DSL line or line bundle. To minimize interference between PSDs assign a single limit mask profile to a DSL line or line bundle.
Page 234 Chapter 11 Subscriber Port Setup Screens Figure 139 VDSL Port Setup: Advanced: Optionmask The following table describes the fields in this screen. Table 89 VDSL Port Setup: Advanced: Optionmask LABEL DESCRIPTION Use the check boxes to disable individual features. Use the All check box to select every feature check box.
Page 235: The Psd Chart Parameter Screen
Chapter 11 Subscriber Port Setup Screens Table 89 VDSL Port Setup: Advanced: Optionmask (continued) LABEL DESCRIPTION Enable US PTM Select this to enable upstream packet transfer mode (PTM). This boosts optimization performance by improving the payload passthrough rate. To use this feature a CPE device which supports this feature is required.
Page 236: Transparent Lan Service (Tls)
Chapter 11 Subscriber Port Setup Screens Figure 140 VDSL PSD Chart Parameter The following table describes the labels in this screen. Table 90 VDSL PSD Chart Parameter LABEL DESCRIPTION Break Point This index number identifies each incremental break point. You can configure 32 break points in total.
Page 237: Tls Network Example
Chapter 11 Subscriber Port Setup Screens Use TLS to add an outer VLAN tag to the inner IEEE 802.1Q tagged frames that enter the network. By tagging the tagged frames (“double-tagged” frames), the service provider can manage up to 4,094 VLAN groups with each group containing up to 4,094 customer VLANs. This allows a service provider to provide different services, based on specific VLANs, for many different customers.
Page 238: Vdsl Vlan Setup
Chapter 11 Subscriber Port Setup Screens TPID (Tag Protocol Identifier) is the customer IEEE 802.1Q tag. Priority refers to the IEEE 802.1p standard that allows the service provider to prioritize traffic based on the class of service (CoS) the customer has paid for. •...
Page 239 Chapter 11 Subscriber Port Setup Screens Figure 142 VDSL VLAN Setup The following table describes the fields in this screen. Table 94 VDSL Port Setup: VLAN Setup LABEL DESCRIPTION Click this to return to the previous screen. PVID / Priority PVID refers to the customer’s VLAN ID.
Page 240: Vdsl Pvlan Setup
Chapter 11 Subscriber Port Setup Screens Table 94 VDSL Port Setup: VLAN Setup (continued) LABEL DESCRIPTION Select the check box to tag all frames transmitted on this port with the port’s VID. Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 241: Vdsl2 Port Setup
Chapter 11 Subscriber Port Setup Screens The following table describes the fields in this screen. Table 95 VDSL Port Setup: PVLAN Setup LABEL DESCRIPTION Click this to return to the previous screen. Enter the VLAN ID (from 1 to 4094) of the VLAN to add to untagged frames of the protocol specified in this PVLAN configuration.
Page 242 Chapter 11 Subscriber Port Setup Screens Figure 144 Port > VDSL2 The following table describes the fields in this screen. Table 96 Port > VDSL2 LABEL DESCRIPTION Slot Select the number of a line card’s slot. The corresponding subscriber port setup screen for the type of line card you selected automatically displays.
Page 243 Chapter 11 Subscriber Port Setup Screens Table 96 Port > VDSL2 (continued) LABEL DESCRIPTION PVID / Priority Specify the port VLAN ID (1~4094) and IEEE 802.1p priority (0~7) to add to untagged frames received on this port. If an untagged frame matches a PVLAN setting, the system uses the PVLAN setting instead.
Page 244: Vdsl2 Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens Table 96 Port > VDSL2 (continued) LABEL DESCRIPTION Up Time This field displays how long the line card has been running since the last time it was started. Firmware This field displays the current firmware version installed on the line card. 11.9.1 VDSL2 Port Setup Line Card Screen Click Port >...
Page 245: Shdsl Port Setup
Chapter 11 Subscriber Port Setup Screens Table 97 Port > VDSL2: Line Card (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 246 Chapter 11 Subscriber Port Setup Screens Figure 148 SHDSL Port Setup The following table describes the fields in this screen. Table 98 SHDSL Port Setup LABEL DESCRIPTION Slot Select the number of a line card’s slot. The corresponding subscriber port setup screen for the type of line card you selected automatically displays.
Page 247 Chapter 11 Subscriber Port Setup Screens Table 98 SHDSL Port Setup (continued) LABEL DESCRIPTION Stuc Alarm Profile Select an alarm profile to define the thresholds that trigger an alarm on the port when exceeded. This alarm profile is for the STU-C (SHDSL Termination Unit - Central) end point.
Page 248: Shdsl Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens Table 98 SHDSL Port Setup (continued) LABEL DESCRIPTION State This field displays the line card’s current operational status. active means the line card is operating normally. init means the MSC is initializing the line card. disable means a manager has disabled the line card.
Page 249 Chapter 11 Subscriber Port Setup Screens The following table describes the fields in this screen. Table 99 SHDSL Port Setup: Line Card LABEL DESCRIPTION Click this to return to the previous screen. Copy Do the following to copy settings from one DSL port to another DSL port or ports. 1.
Page 250: Shdsl Port Setup Advanced
Chapter 11 Subscriber Port Setup Screens 11.10.2 SHDSL Port Setup Advanced Click Port > SHDSL in the navigation panel to open the SHDSL Port Setup screen. Click the Setup button to open the following screen. Use this screen to configure an SHDSL port’s detailed settings.
Page 251: Permanent Virtual Circuits
Chapter 11 Subscriber Port Setup Screens Table 100 SHDSL Port Setup: Advanced (continued) LABEL DESCRIPTION Stur Alarm Profile Select an alarm profile to define the thresholds that trigger an alarm on the port when exceeded. This alarm profile is for the STU-R (SHDSL Termination Unit - Remote) end point.
Page 252: Llc
Chapter 11 Subscriber Port Setup Screens The system can handle multiple IEEE 802.1p priority queues on a single PVC. You can also define up to eight PVCs on a DSL port and use them for different services or levels of service. You set the PVID that is assigned to untagged frames received on each channel.
Page 253 Chapter 11 Subscriber Port Setup Screens Figure 153 PVC Setup The following table describes the fields in this screen. Table 101 PVC Setup LABEL DESCRIPTION PVC Table This table displays the PVCs that are configured for the selected port. Slot Select the number of a line card’s slot.
Page 254 Chapter 11 Subscriber Port Setup Screens Table 101 PVC Setup (continued) LABEL DESCRIPTION Priority This field displays the priority value (0 to 7) that the line card adds to frames that come in on this PVC without a (IEEE 802.1p) priority tag. Mvlan This field displays the PVC’s current multicast VLAN setting.
Page 255: Pvc Setup Slot Screen
Chapter 11 Subscriber Port Setup Screens Table 101 PVC Setup (continued) LABEL DESCRIPTION Cancel Click Cancel to begin configuring the screen again. This column lists the slot numbers of the line cards. Click the ID number of an active DSL line card to go to a screen where you can view and delete PVCs from the line card’s DSL ports.
Page 256: Pvc Setup Vlan Screen
Chapter 11 Subscriber Port Setup Screens Table 102 PVC Setup: Slot (continued) LABEL DESCRIPTION PVID This field displays the PVID (Port VLAN ID) to assign to untagged frames received on this channel. Priority This field displays the priority value (0 to 7) that the line card adds to frames that come in on this PVC without a (IEEE 802.1p) priority tag.
Page 257: Pvc Setup Pvlan Screen
Chapter 11 Subscriber Port Setup Screens Table 103 PVC Setup: VLAN (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 258: Port Copy Screen
Chapter 11 Subscriber Port Setup Screens The following table describes the fields in this screen. Table 104 PVC Setup: PVLAN LABEL DESCRIPTION Click this to return to the previous screen. VPI / VCI This field displays the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI).
Page 259: Ip Bridge Overview
Chapter 11 Subscriber Port Setup Screens Figure 158 Port Copy The following table describes the fields in this screen. Table 105 Port Copy LABEL DESCRIPTION Slot Select the number of a line card’s slot. Port Select the number of a DSL port on the line card. Copy Do the following to copy settings from one DSL port to another DSL port or ports.
Page 260 Chapter 11 Subscriber Port Setup Screens Figure 160 IP Bridge: Traditional vs. IP-aware DSLAM Traditional Forward by destination MAC IP Aware Forward by destination IP The IP-aware MSC does not modify the IP packet header, but it uses the destination IP address to modify the layer-2 header, in particular the source MAC address, destination MAC address, and VLAN tag.
Page 261: Upstream And Downstream Traffic
Chapter 11 Subscriber Port Setup Screens 11.14.1 Upstream and Downstream Traffic When the MSC forwards upstream traffic, it makes the following changes in the layer-2 header. Table 106 IP Bridge: Layer-2 Header for Upstream Traffic ORIGINAL UPDATED Source MAC address Subscriber’s MAC address MSC’s MAC address Destination MAC address...
Page 262: Ip Bridge Settings
Chapter 11 Subscriber Port Setup Screens 11.14.2 IP Bridge Settings The IP bridge function consists of the following settings. • Domains and VLANs • Edge routers • Downlink interfaces • Routing tables • PVCs • ARP proxy settings Each set of settings is discussed in more detail in the following sections. 11.14.2.1 Domains and VLAN A domain represents an ISP.
Page 263: Ip Bridge Configuration
Chapter 11 Subscriber Port Setup Screens 11.14.2.4 Routing Tables Each domain has its own routing table. Each routing table contains entries that, based on the destination IP address, control where the MSC forwards packets (for upstream and downstream traffic). The MSC automatically creates routing table entries for each downlink interface and for each edge router in the domain.
Page 264: Ipb Domain Screen
Chapter 11 Subscriber Port Setup Screens Figure 162 IPB ARP Proxy The following table describes the labels in this screen. Table 107 IPB ARP Proxy LABEL DESCRIPTION Aging Time Enter a number of seconds (10~10000) to set how long the MSC keeps ARP table entries for IP bridge domains.
Page 265 Chapter 11 Subscriber Port Setup Screens Figure 163 IPB Domain The following table describes the labels in this screen. Table 108 IPB Domain LABEL DESCRIPTION Name Enter the name of the domain you want to create. You can use 1-31 printable English keyboard characters, except for right angle brackets (>).
Page 266: Ipb Edgerouter Screen
Chapter 11 Subscriber Port Setup Screens Table 108 IPB Domain (continued) LABEL DESCRIPTION Index This field displays the index number of the VLAN in the domain. VLAN This field displays the ID of each VLAN in the domain. Select Select the check box in the Select column for an entry and click Delete to remove the entry.
Page 267: Ipb Interface Screen
Chapter 11 Subscriber Port Setup Screens The following table describes the labels in this screen. Table 109 IPB Edgerouter LABEL DESCRIPTION Edgerouter IP Enter the IP address of the edge router. NetMask Enter the number of bits in the subnet mask of the edge router. Enter the ID of the VLAN of which the edge router is a member.
Page 268 Chapter 11 Subscriber Port Setup Screens Figure 165 IPB Interface The following table describes the labels in this screen. Table 110 IPB Interface LABEL DESCRIPTION Use the top section to create downlink interfaces manually. Interface IP Enter the IP address and the number of bits in the subnet mask that define the range of IP addresses to which this downlink interface applies.
Page 269: Ipbpvc Screen
Chapter 11 Subscriber Port Setup Screens Table 110 IPB Interface (continued) LABEL DESCRIPTION Interface IP This field displays the IP address and the number of bits in the subnet mask that define the range of IP addresses to which this downlink interface applies. If the NetMask destination IP address of a packet is in this range, the MSC tries to forward the frame to a subscriber in the specified VLAN and PVC, if any.
Page 270 Chapter 11 Subscriber Port Setup Screens Figure 166 IPBPVC The following table describes the labels in this screen. Table 111 IPBPVC LABEL DESCRIPTION Slot Use this drop-down list box to select the slot that contains a line card with a port for which you wish to set up an IP bridge PVC.
Page 271 Chapter 11 Subscriber Port Setup Screens Table 111 IPBPVC (continued) LABEL DESCRIPTION Select Select the radio button in the Select column for an entry and click Modify to be able to edit the entry, Copy to duplicate the entry’s settings on another port, or Delete to remove the entry.
Page 272: Ipbpvc Vlan Setup Screen
Chapter 11 Subscriber Port Setup Screens Table 111 IPBPVC (continued) LABEL DESCRIPTION State This field displays the line card’s current operational status. active means the line card is operating normally. init means the MSC is initializing the line card. disable means a manager has disabled the line card. inactive means the line card is starting up or is not operating normally.
Page 273: Ipbpvc By Slot Screen
Chapter 11 Subscriber Port Setup Screens Table 112 IPBPVC: VLAN Setup (continued) LABEL DESCRIPTION Apply Click Apply to save changes on the selected IPB PVC. Clicking Apply saves your changes to the MSC’s volatile memory. The MSC loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non-volatile memory when you are done configuring.
Page 274: Ipb Route Screen
Chapter 11 Subscriber Port Setup Screens Table 113 IPBPVC: Slot (continued) LABEL DESCRIPTION Port This field displays the port number of a port on this line card that has an IPB PVC. VPI/VCI This field displays the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI).
Page 275 Chapter 11 Subscriber Port Setup Screens The following table describes the labels in this screen. Table 114 IPB Route LABEL DESCRIPTION Use the top section to create routing table entries manually. Domain Select the domain to whose routing table you want to add this entry. Route IP Enter the IP address and the number of bits in the subnet mask that define the range of IP addresses to which this entry applies.
Page 276: G.bond Screen
Chapter 11 Subscriber Port Setup Screens Table 114 IPB Route (continued) LABEL DESCRIPTION Change Pbit If you set the MSC to change the IEEE 802.1p priority value of incoming frames, this field displays the priority value (0 to 7) to which the MSC sets them. “-” displays if you do not set the MSC to change the IEEE 802.1p priority value of incoming frames.
Page 277 Chapter 11 Subscriber Port Setup Screens Figure 171 SHDSL Pair Bonding Example Internet The following shows how to use the G.bond Setup screen to configure port bonding settings. Before you begin you need to have an active ADSL or SHDSL line card installed and connected to multiple DSL lines.
Page 278 Chapter 11 Subscriber Port Setup Screens Figure 172 Port > G.bond The following table describes the labels in this screen. Table 115 Port > G.bond LABEL DESCRIPTION Slot Select the number of a line card’s slot to apply G.bond settings on traffic through this card.
Page 279: The Voip Sip Port Setup Screen
Chapter 11 Subscriber Port Setup Screens Table 115 Port > G.bond LABEL DESCRIPTION Member Port This link displays the ports configured to a group. If no ports have been configured to a group, the link will show “None”. Click this link to display a popup screen. Select the port(s) in this screen to allocate them to the DSL line group.
Page 280 Chapter 11 Subscriber Port Setup Screens Figure 173 Port > VoIP SIP Screen The following table describes the labels in this screen. Table 116 Port > VoIP SIP Setup Screen LABEL DESCRIPTION Slot Use the drop-down list boxes to select the port on an active VoIP line card you want to configure.
Page 281 Chapter 11 Subscriber Port Setup Screens Table 116 Port > VoIP SIP Setup Screen LABEL DESCRIPTION DSP Profile Select the digital signal processing profile the port is to use. A DSP profile contains information about the codecs (coders/decoders) If you have not configured any profiles, only the default profile DEFVAL can be selected.
Page 282: The Sip Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens Table 116 Port > VoIP SIP Setup Screen LABEL DESCRIPTION This column displays the line card’s slot number. Click a SIP line card’s number to go to the card’s SIP Port Setup Line Card screen (see Section 11.23 on page 282) where you can see and edit all a SIP line card’s VoIP...
Page 283 Chapter 11 Subscriber Port Setup Screens The following table describes the labels in this screen. Table 117 The Port > VoIP SIP Setup > SIP Port Setup Line Card Screen LABEL DESCRIPTION Click this to return to the Port > VoIP SIP screen. Copy Use this to assign the selected port’s settings to other ports.
Page 284: Advanced Sip Port Setup Screen
Chapter 11 Subscriber Port Setup Screens 11.24 Advanced SIP Port Setup Screen Use this screen to configure the VoIP settings of a port on your SIP VoIP line card. Click a port number in the Port SIP Setup Line Card screen (see Section 11.23 on page 282).
Page 285: The H248 Port Setup Screen
Chapter 11 Subscriber Port Setup Screens Table 118 The Advanced Port SIP Setup Screen LABEL DESCRIPTION Impedance This field displays the default VoIP port AC impedance. The default impedance value depends on the country code (configured in the VoIP > Countrycode screen).
Page 286 Chapter 11 Subscriber Port Setup Screens Figure 178 Port > VoIP H248 Screen The following table describes the labels in this screen. Table 119 Port > VoIP H248 Screen LABEL DESCRIPTION Slot Use the drop-down list boxes to select the port on an active VoIP line card you want to configure.
Page 287 Chapter 11 Subscriber Port Setup Screens Table 119 Port > VoIP H248 Screen LABEL DESCRIPTION Impedance This field displays the default VoIP port AC impedance. The default impedance value depends on the country code (configured in the VoIP > Countrycode screen). If you do not want to use the default impedance, select the required AC impedance of the VoIP port from the drop-down list.
Page 288: The H.248 Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens Table 119 Port > VoIP H248 Screen LABEL DESCRIPTION Card Type This displays a line card’s model name. Up Time This field displays how long the line card has been running since it was started up.
Page 289: The Advanced H248 Port Setup Screen
Chapter 11 Subscriber Port Setup Screens The following table describes the labels in this screen. Table 120 Port > VoIP H248 Setup > H248 Port Setup Line Card Screen LABEL DESCRIPTION Click this to return to the Port > VoIP H248 screen. Copy Use this to assign the selected port’s settings to other ports.
Page 290 Chapter 11 Subscriber Port Setup Screens The fields that display in this screen are the same as those in the H248 Port Setup screen (see Section 11.25 on page 285). Figure 182 The Advanced H248 Port Setup Screen The following table describes the labels in this screen. Table 121 The Advanced H248 Port Setup Screen LABEL DESCRIPTION...
Page 291: Enet Port Setup
Chapter 11 Subscriber Port Setup Screens 11.28 ENET Port Setup Click Port > ENET in to open the following screen. Use this screen to configure settings for individual subscriber Ethernet ports. Figure 183 ENET Port Setup The following table describes the fields in this screen. Table 122 ENET Port Setup LABEL DESCRIPTION...
Page 292 Chapter 11 Subscriber Port Setup Screens Table 122 ENET Port Setup (continued) LABEL DESCRIPTION PVID / Priority Specify the port VLAN ID (1~4094) and IEEE 802.1p priority (0~7) to add to untagged frames received on this port. If you configure an ENET PVID setting and enable TLS, the system does not apply the PVID.
Page 293: Enet Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens Table 122 ENET Port Setup (continued) LABEL DESCRIPTION Up Time This field displays how long the line card has been running since the last time it was started. Firmware This field displays the current firmware version installed on the line card. 11.28.1 ENET Port Setup Line Card Screen Click Port >...
Page 294: Enet Vlan Setup
Chapter 11 Subscriber Port Setup Screens Table 123 ENET Port Setup: Line Card (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 295 Chapter 11 Subscriber Port Setup Screens The following table describes the fields in this screen. Table 124 ENET Port Setup: VLAN Setup LABEL DESCRIPTION Click this to return to the previous screen. PVID / Priority Specify the port VLAN ID (1~4094) and IEEE 802.1p priority (0~7) to add to untagged frames received on this port.
Page 296: Enet Dot3Ad Setup
Chapter 11 Subscriber Port Setup Screens 11.28.3 ENET Dot3ad Setup Click Port > ENET in the navigation panel to open the ENET Port Setup screen. Select an Ethernet line card ID, a port index number and click Setup next to Dot3ad to open the following screen.
Page 297: Dtpvc Setup Screen
Chapter 11 Subscriber Port Setup Screens Table 125 ENET Dot3ad Setup (continued) LABEL DESCRIPTION Dynamic (LACP) Select this check box to use Link Aggregate Control Protocol (LACP), to dynamically create and manage the trunk group. If the peer switch does not support LACP, clear this check box to use static trunking.
Page 298 Chapter 11 Subscriber Port Setup Screens Figure 189 DTPVC Setup The following table describes the fields in this screen. Table 126 DTPVC Setup LABEL DESCRIPTION DTPVC This table displays the DTPVCs that are configured for the selected port. Table Slot Select the number of a line card’s slot.
Page 299 Chapter 11 Subscriber Port Setup Screens Table 126 DTPVC Setup (continued) LABEL DESCRIPTION CVID This is the customer VLAN ID (the inner VLAN tag) that the line card assigns to untagged frames received on this DTPVC. CPri This field displays the IEEE 802.1p priority level for the customer tag that the line card adds to untagged frames that come in on this DTPVC.
Page 300: Dtpvc Setup Slot Screen
Chapter 11 Subscriber Port Setup Screens 11.29.1 DTPVC Setup Slot Screen Click Port > DTPVC in the navigation panel to open the DTPVC Setup screen. Click an active ADSL or SHDSL line card’s ID number to open the following screen. Use this screen to view and delete DTPVCs from the line card’s DSL ports.
Page 301 Chapter 11 Subscriber Port Setup Screens Figure 191 E1 Port Setup The following table describes the fields in this screen. Table 128 E1 Port Setup LABEL DESCRIPTION E1 Port This table displays the E1 port settings that are configured for the selected port. Setup Table Slot Select the number of a line card’s slot.
Page 302: E1 Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens Table 128 E1 Port Setup (continued) LABEL DESCRIPTION Copy Do the following to copy the settings you configure above to another port or ports. 1. Click Copy. 2. Select to which line card you want to copy the settings. 3.
Page 303: E1 Port Setup Advanced
Chapter 11 Subscriber Port Setup Screens The following table describes the fields in this screen. Table 129 E1 Port Setup: Line Card LABEL DESCRIPTION Click this to return to the previous screen. Copy Select a port in the Select column and then do the following to copy the settings from the port to another port or ports.
Page 304: Xvlan
Chapter 11 Subscriber Port Setup Screens The following table describes the fields in this screen. Table 130 E1 Port Setup: Advanced LABEL DESCRIPTION Click this to return to the previous screen. Enable Select this to turn this port on. Impedence Select the impedance (in ohms) the IMA line card should use for the E1 port.
Page 305: Xvlan Setup
Chapter 11 Subscriber Port Setup Screens Figure 194 xVLAN Example 11.31.1 xVLAN Setup Click Port > Xvlan in the navigation panel to open the Xvlan Setup screen. Use this screen to configure xVLAN settings for individual ports. Figure 195 Port > Xvlan The following table describes the fields in this screen.
Page 306: Xvlan Port Setup Line Card Screen
Chapter 11 Subscriber Port Setup Screens Table 131 Port > Xvlan (continued) LABEL DESCRIPTION Svid This is the service provider VLAN ID used on the service provider’s network. Cvid-S This applies to the VLC13XXG cards. This is the translated customer VLAN ID used on the service provider’s network.
Page 307 Chapter 11 Subscriber Port Setup Screens The following table describes the fields in this screen. Table 132 Port > Xvlan: Line Card LABEL DESCRIPTION Click this to return to the previous screen. Delete Select one or more entries’ Select radio buttons and then click Delete to remove them.
Page 308 Chapter 11 Subscriber Port Setup Screens MSC1000G/1024G/1224G Series User’s Guide...
Page 309: Ima Screens
H A P T E R IMA Screens This chapter describes how to configure settings related to the E1 ports on an IMA line card. 12.1 IMA Overview Inverse Multiplexing for ATM (IMA) is a technology used to transmit ATM traffic over a bundle of T1 or E1 lines.
Page 310 Chapter 12 IMA Screens Figure 197 Untagged DTPVCs IMA1 IMA2 DTPVC1 Network (S1,C1) (S1,C1) DTPVC2 (S1,C2) (S1,C2) DTPVC3 (S1,C3) (S1,C3) In order to reduce management hassle, you can use one tagged PVC to preserve the S-tags and C-tags in the ATM cells. To use the tagged PVC settings, you must make sure the remote IMA device also supports tagged PVC.
Page 311: Before You Begin
Chapter 12 IMA Screens 12.3 Before You Begin • Make sure all frames have either one or two VLAN tag(s) for multiple service providers to differentiate their own traffic. You have to configure the VLAN settings for xDSL and the MSC management line cards.
Page 312 Chapter 12 IMA Screens Table 133 IMA Group Setup (continued) LABEL DESCRIPTION Link This field displays the number of a single or multiple IMA links that are members of this group. none displays if this group does not have any members yet. Click none or the IMA link(s) to display the following screen where you can configure the link members.
Page 313: The Pvc Setup Screen
Chapter 12 IMA Screens Table 133 IMA Group Setup (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 314 Chapter 12 IMA Screens The following table describes the fields in this screen. Table 134 PVC Setup LABEL DESCRIPTION PVC Table This table displays the PVC settings that are configured for the selected IMA group. Slot Select the number of an IMA line card’s slot. The corresponding subscriber port setup screen for the type of line card you selected automatically displays.
Page 315: The Pvc Setup Slot Screen
Chapter 12 IMA Screens Table 134 PVC Setup (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 316: The Dtpvc Setup Screen
Chapter 12 IMA Screens Table 135 IMA > PVC Setup: Slot (continued) LABEL DESCRIPTION Next Click Next to show the following screen if the information cannot be displayed in one screen. Next 10 Click Next 10 to show the following 10 pages of alarms. Index This is the number of the DTPVC.
Page 317 Chapter 12 IMA Screens The following table describes the fields in this screen. Table 136 DTPVC Setup LABEL DESCRIPTION DTPVC Table This table displays the PVC settings that are configured for the selected IMA group. Slot Select the number of an IMA line card’s slot. The corresponding group setup screen for the type of line card you selected automatically displays.
Page 318: The Dtpvc Setup Slot Screen
Chapter 12 IMA Screens Table 136 DTPVC Setup (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 319: Mgtpvc Overview
Chapter 12 IMA Screens Table 137 IMA > DTPVC Setup: Slot (continued) LABEL DESCRIPTION Next Click Next to show the following screen if the information cannot be displayed in one screen. Next 10 Click Next 10 to show the following 10 pages of alarms. Index This is the number of the DTPVC.
Page 320: The Mgtpvc Setup Screen
Chapter 12 IMA Screens Figure 205 Routed MGTPVC Configuration Example IMA-1 IMA-2 192.168.1.3 192.168.1.2 192.168.1.1 To configure the settings on the IES for IMA-1, make sure that you configure the Ip and Gateway fields while configuring the other fields in the IMG > MGTPVC screen as shown next.
Page 321 Chapter 12 IMA Screens Figure 206 MGTPVC Setup The following table describes the fields in this screen. Table 138 MGTPVC Setup LABEL DESCRIPTION MGTPVC Table This table displays the management PVC settings that are configured for the selected IMA group. Slot Select the number of an IMA line card’s slot.
Page 322: The Mgtpvc Setup Slot Screen
Chapter 12 IMA Screens Table 138 MGTPVC Setup (continued) LABEL DESCRIPTION Previous Click Previous to show the preceding screen if the information cannot be displayed in one screen. Page X of X This identifies which page of information is displayed and the total number of pages of information.
Page 323 Chapter 12 IMA Screens Figure 207 IMA > MGTPVC Setup: Slot The following table describes the fields in this screen. Table 139 IMA > MGTPVC Setup: Slot LABEL DESCRIPTION Click this to return to the previous screen. Delete Click Delete to remove the selected management PVC(s). Previous 10 Click Previous 10 to show the preceding 10 pages of information.
Page 324 Chapter 12 IMA Screens MSC1000G/1024G/1224G Series User’s Guide...
Page 325: Profile Screens
H A P T E R Profile Screens This chapter describes how to configure profiles to use in assigning settings to the DSL ports. 13.1 Profiles Overview A profile is a list of settings that you define. Then you can use them to configure one or more individual ports or PVCs.
Page 326: Fast Mode
Chapter 13 Profile Screens Reed-Solomon codes are block-based error correcting codes with a wide range of applications. The Reed-Solomon encoder takes a block of digital data and adds extra "redundant" bits. The Reed-Solomon decoder processes each block and attempts to correct errors and recover the original data.
Page 327 Chapter 13 Profile Screens Figure 208 ADSL Profile The following table describes the fields in this screen. Table 140 ADSL Profile LABEL DESCRIPTION The top part of the screen is for profile configuration. Name When editing a profile, this is the name of this profile. When adding a profile, type a name (up to 31 characters) for the profile.
Page 328 Chapter 13 Profile Screens Table 140 ADSL Profile (continued) LABEL DESCRIPTION Min SNR (0.1 Type the minimum upstream signal to noise margin (measured in tenths of a decibel). Configure the minimum upstream signal to noise margin to be less than or equal to the maximum upstream signal to noise margin.
Page 329: Vdsl Profile Setup
Chapter 13 Profile Screens Table 140 ADSL Profile (continued) LABEL DESCRIPTION Down-shift The downstream down shift signal to noise margin (measured in tenths of a Noise Margin decibel). When the channel’s signal to noise margin goes below this number, the (0.1 dB) device shifts to a lower transfer rate.
Page 330 Chapter 13 Profile Screens Figure 209 VDSL Profile The following table describes the fields in this screen. Table 141 VDSL Profile LABEL DESCRIPTION The top part of the screen is for profile configuration. Name When editing a profile, this is the name of this profile. When adding a profile, type a name (up to 31 characters) for the profile.
Page 331 Chapter 13 Profile Screens Table 141 VDSL Profile (continued) LABEL DESCRIPTION Interleave Configure this field when you set the Latency Mode field to Interleave. Type the Delay (ms) number of milliseconds of interleave delay to use for upstream transfers. It is recommended that you configure the same latency delay for both upstream and downstream.
Page 332: Vdsl2 Profiles
Chapter 13 Profile Screens Table 141 VDSL Profile (continued) LABEL DESCRIPTION Up-shift Noise The downstream up shift signal to noise margin (measured in tenths of a decibel). Margin When the channel’s signal to noise margin goes above this number, the device can attempt to use a higher transfer rate.
Page 333: Vdsl2 Profile Example
Chapter 13 Profile Screens 13.6.2 VDSL2 Profile Example This example shows you the configuration relationships between VDSL2 templates, VDSL2 line profiles, VDSL2 line channel profiles, and subscriber ports. Since each VDSL2 line may have different loop conditions, you need to configure several VDSL2 line profiles and channel profiles in the Profile >...
Page 334: Vdsl2 Line Profile Setup
Chapter 13 Profile Screens Figure 210 Profile > VDSL2 The following table describes the labels in this screen. Table 144 Profile > VDSL2 LABEL DESCRIPTION Name Enter a descriptive name to identify this template. VDSL2 Line Profile Select a line profile for this VDSL2 template. You can configure line profiles by clicking the LineProfile link in the right-top corner of the screen.
Page 335 Chapter 13 Profile Screens Figure 211 Profile > VDSL2 > LineProfile The following table describes the labels in this screen. Table 145 Profile > VDSL2 > LineProfile LABEL DESCRIPTION Name Enter a descriptive name for identification purposes. VDSL2 Profile Specify the VDSL2 profile(s) you want to apply to this line profile. See Section 11.2.4 on page 210 for more information.
Page 336 Chapter 13 Profile Screens Table 145 Profile > VDSL2 > LineProfile (continued) LABEL DESCRIPTION Bitswap Select On to allow on-line bits and power (for example, margin) reallocation among the allowed sub-carriers without service interruption or errors. This helps to keep transmission data rates on a high SNR VDSL2 line. Select Off to disable it.
Page 337 Chapter 13 Profile Screens Table 145 Profile > VDSL2 > LineProfile (continued) LABEL DESCRIPTION Rate Adaptive This field displays downstream (DS) and upstream (US) rate adaptive settings. Manual displays if the system fixes the transmission rate as the minimum net data rate and disables transmission rate adjustment.
Page 338: Vdsl2 Line Profile Setup > Rate Adaptive
Chapter 13 Profile Screens 13.7.2 VDSL2 Line Profile Setup > Rate Adaptive Click the Modify link next to the Rate Adaptive field in the VDSL2 Line Profile Setup screen to open the screen as shown next. Use the screen to configure detailed rate adaption settings.
Page 339: Vdsl2 Line Profile Setup > Mib Psd Mask
Chapter 13 Profile Screens 13.7.3 VDSL2 Line Profile Setup > MIB PSD Mask Click the Modify link next to the MIB PSD MASK field in the VDSL2 Line Profile Setup screen to open the screen as shown next. Use this screen to adjust PSD levels for tones based on the scope down the limit PSD mask you have configured.
Page 340: Vdsl2 Line Profile Setup > Dpbo
Chapter 13 Profile Screens The following table describes the labels in this screen. Table 147 Profile > VDSL2 > LineProfile > MIB PSD Mask LABEL DESCRIPTION MIB PSD Mask This displays the PSD mask result in a graph. The MIB PSD mask is defined only within the operating bands and lies at or below the limit PSD mask.
Page 341 Chapter 13 Profile Screens Figure 214 Profile > VDSL2 > LineProfile > DPBO The following table describes the labels in this screen. Table 148 Profile > VDSL2 > LineProfile > DPBO LABEL DESCRIPTION DPBOESEL Specify the electrical length of the cable between the system and CPE devices. Section 11.2.9 on page 212.
Page 342: Vdsl2 Line Profile Setup > Rfi Band
Chapter 13 Profile Screens Table 148 Profile > VDSL2 > LineProfile > DPBO (continued) LABEL DESCRIPTION DPBOFMIN This defines the minimum frequency from which the DPBO shall be applied. Enter from 0 kHz to 8832 kHz in steps of 4.3125 kHz. DPBOFMAX This defines the maximum frequency at which DPBO may be applied.
Page 343: Vdsl2 Line Profile Setup > Virtual Noise
Chapter 13 Profile Screens Figure 215 Profile > VDSL2 > LineProfile > RFI The following table describes the labels in this screen. Table 149 Profile > VDSL2 > LineProfile > RFI LABEL DESCRIPTION Start Use these columns below this field to specify the starting frequencies for each RFI band.
Page 344 Chapter 13 Profile Screens Figure 216 Profile > VDSL2 > LineProfile > Virtual Noise MSC1000G/1024G/1224G Series User’s Guide...
Page 345: Vdsl2 Channel Profile Setup
Chapter 13 Profile Screens The following table describes the labels in this screen. Table 150 Profile > VDSL2 > LineProfile > Virtual Noise LABEL DESCRIPTION Virtual Noise This displays the virtual noise setting result in a graph. If there is too much noise on a line, the allowed line speed may be reduced or the line may not initialized.
Page 346 Chapter 13 Profile Screens Figure 217 Profile > VDSL2 > ChanProfile The following table describes the labels in this screen. Table 151 Profile > VDSL2 > ChanProfile LABEL DESCRIPTION Name Enter a descriptive name for identification purposes. DownStream The parameters in this column relate to downstream transmissions. Upstream The parameters in this column relate to upstream transmissions.
Page 347: Configured Versus Actual Shdsl Rates
Chapter 13 Profile Screens Table 151 Profile > VDSL2 > ChanProfile LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 348: Shdsl Profile Screen
Chapter 13 Profile Screens 13.10 SHDSL Profile Screen Click Profile > SHDSL in the navigation panel to open the following screen. Use this screen to configure SHDSL profiles. Later you can apply the SHDSL profiles to configure SHDSL ports in the SHDSL Port Setup screens. Figure 218 SHDSL Profile The following table describes the fields in this screen.
Page 349: Atm Qos
Chapter 13 Profile Screens Table 152 SHDSL Profile (continued) LABEL DESCRIPTION Line Probing The SHDSL line card and subscriber modem use line probes to determine the Enable Mode best possible transmission rate. This is used in rate adaptation. Disable the line probe to have the system skip the rate adaptation phase to shorten connection set up time.
Page 350: Atm Traffic Classes
Chapter 13 Profile Screens Traffic shaping controls outgoing (downstream) traffic, not incoming (upstream) traffic. 13.12.1 ATM Traffic Classes These are the basic ATM traffic classes defined by the ATM Forum Traffic Management 4.0 Specification. 13.12.1.1 Constant Bit Rate (CBR) Constant Bit Rate (CBR) is an ATM traffic class that provides fixed bandwidth. CBR traffic is generally time-sensitive (doesn't tolerate delay).
Page 351 Chapter 13 Profile Screens 13.12.2.2 Sustained Cell Rate (SCR) Sustained Cell Rate (SCR) is the mean cell rate of each bursty traffic source. It specifies the maximum average rate at which cells can be sent over the virtual connection. SCR may not be greater than the PCR.
Page 352: Atm Profile Screen
Chapter 13 Profile Screens Figure 220 TAT, CDVT and BT in Traffic Shaping 13.13 ATM Profile Screen Click Profile > ATM in the navigation panel to open the following screen. Use this screen to configure ATM profiles. Later you can use the ATM profiles to configure PVCs in the PVC Setup screens.
Page 353: Alarm Adsl Profile Screen
Chapter 13 Profile Screens Table 153 ATM Profile (continued) LABEL DESCRIPTION Cell Delay Cell Delay Variation Tolerance is the accepted tolerance of the difference between a Variation cell’s transfer delay and the expected transfer delay. Cell Delay Variation Tolerance Tolerance applies with all of the ATM traffic classes.
Page 354 Chapter 13 Profile Screens Figure 222 Alarm ADSL Profile The following table describes the fields in this screen. Table 154 Alarm ADSL Profile LABEL DESCRIPTION The top part of the screen is for profile configuration. Name Type a name to identify the alarm profile (you cannot change the name of the DEFVAL profile).
Page 355: Alarm Vdsl Profile Screen
Chapter 13 Profile Screens Table 154 Alarm ADSL Profile (continued) LABEL DESCRIPTION 15 Min SESL This field sets the limit for the number of Severely Errored Seconds that are [0~900] permitted to occur within 15 minutes. 15 Min UASL This field sets the limit for the number of UnAvailable Seconds that are permitted [0~900] to occur within 15 minutes.
Page 356 Chapter 13 Profile Screens Figure 223 Alarm VDSL Profile The following table describes the fields in this screen. Table 155 Alarm VDSL Profile LABEL DESCRIPTION The top part of the screen is for profile configuration. Name Type a name to identify the alarm profile (you cannot change the name of the DEFVAL profile).
Page 357: Alarm Vdsl2 Profile Setup
Chapter 13 Profile Screens Table 155 Alarm VDSL Profile (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 358: Alarm Vdsl2 Line Profile Setup
Chapter 13 Profile Screens Table 156 Profile > Alarm VDSL2 (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 359: Alarm Vdsl2 Channel Profile Setup
Chapter 13 Profile Screens The following table describes the labels in this screen. Table 157 Profile > Alarm VDSL2 > LineProfile LABEL DESCRIPTION Name Enter a descriptive name for identification purposes. 15 Min Enter the number of times a full initialization is allowed to fail within 15 minutes. FailedFullInt Threshold XTUC...
Page 360: Alarm Shdsl Profile Screen
Chapter 13 Profile Screens Figure 226 Profile > Alarm VDSL2 > ChanProfile The following table describes the labels in this screen. Table 158 Profile > Alarm VDSL2 > ChanProfile LABEL DESCRIPTION Name Enter a descriptive name for identification purposes. XTUC Configure the thresholds in this column for the system (XTUC).
Page 361 Chapter 13 Profile Screens Figure 227 Alarm SHDSL Profile The following table describes the fields in this screen. Table 159 Alarm SHDSL Profile LABEL DESCRIPTION The top part of the screen is for profile configuration. Name Type a name to identify the alarm profile (you cannot change the name of the DEFVAL profile).
Page 362: Igmp Filter Profile Screen
Chapter 13 Profile Screens Table 159 Alarm SHDSL Profile (continued) LABEL DESCRIPTION While you are modifying a profile, you can click New to start configuring a fresh profile without saving your changes. Cancel Click Cancel to start configuring the screen again. The bottom part of the screen lists the configured profiles.
Page 363 Chapter 13 Profile Screens Figure 228 IGMP Filter Profile The following table describes the fields in this screen. Table 160 IGMP Filter Profile LABEL DESCRIPTION Name Type a name to identify the IGMP filter profile (you cannot change the name of the DEFVAL profile).
Page 364: The Profile Voip Sip Screen
Chapter 13 Profile Screens Table 160 IGMP Filter Profile (continued) LABEL DESCRIPTION Modify Select a profile’s Select radio button and click Modify to edit the profile. Delete Select a profile’s Select radio button and click Delete to remove the profile. 13.19 The Profile VoIP SIP Screen Use this screen to configure basic information about the SIP accounts used by the VOP line cards.
Page 365 Chapter 13 Profile Screens Table 161 Profile > VoIP SIP LABEL DESCRIPTION Port Enter the SIP registrar server’s listening port number, if the VoIP service provider gave you one. Otherwise, enter the same port number you entered in the SIP IP / Domain Name Port field. Proxy Server IP / Domain Enter the IP address or domain name of the SIP server or outbound proxy Name...
Page 366: Profile Voip Sip Call Service Screen
Chapter 13 Profile Screens 13.20 Profile VoIP SIP Call Service Screen Use this screen to configure the call service information used by the system. You can then select a set of call service information (known as a profile) and assign it to a port in the Port > VoIP SIP screen.
Page 367 Chapter 13 Profile Screens The following table describes the labels in this screen. Table 162 Profile > VoIP SIP CALLSVC Screen LABEL DESCRIPTION Name Enter a name for this call service profile (up to 31 ASCII characters; spaces are not allowed). Password for SIP Select OFF if the SIP account this profile uses does not require a Registration...
Page 368 Chapter 13 Profile Screens Table 162 Profile > VoIP SIP CALLSVC Screen LABEL DESCRIPTION Key Pattern Enter the name of a key pattern table for supplementary services. The default key pattern table “DEFVAL” has the following settings: *99#: enable DND (Do Not Disturb). #99#: disable DND.
Page 369: The Profile Voip Dsp Screen
Chapter 13 Profile Screens Table 162 Profile > VoIP SIP CALLSVC Screen LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 370 Chapter 13 Profile Screens Figure 231 The Profile > VoIP DSP Screen The following table describes the labels in this screen. Table 163 The Profile > VoIP DSP Screen LABEL DESCRIPTION Name Enter a name for this DSP profile (up to 31 ASCII characters; spaces are not allowed).
Page 371: The Profile Voip H248 Screen
Chapter 13 Profile Screens Table 163 The Profile > VoIP DSP Screen LABEL DESCRIPTION Priority - Use this to decrease the priority of the selected codec by moving it down one place in the list. Min Play Buffer Delay This is the minimum time delay of the play buffer (10 ~ 500 milliseconds, (10~500) must be less than or equal to the Max Play Buffer Delay).
Page 372 Chapter 13 Profile Screens Figure 232 Profile VoIP H248 Screen The following table describes the labels in this screen. Table 164 Profile VoIP H248 Screen LABEL DESCRIPTION Name Enter a name for this H.248 profile. MGC IP / Domain Name Enter the IP address or domain name of the H.248 media gateway controller.
Page 373: Ipqos Overview
Chapter 13 Profile Screens Table 164 Profile VoIP H248 Screen LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 374: Ieee 802.1P To Ipqos Queue Mapping
Chapter 13 Profile Screens • Level: This is the Strict Priority Queuing (SPQ) priority level (0~7) for each queue. 0 is the lowest priority and 7 is the highest. SPQ services queues by priority only. As traffic comes into the switch, traffic in the highest priority queue (Q7) is transmitted first. When that queue empties, traffic in the next highest-priority queue (Q6) is transmitted until Q6 empties, and then Q5 traffic is transmitted and so on.
Page 375: Ipqos For Vdsl 2 And Adsl2+ To Vdsl2 Migration Examples
Chapter 13 Profile Screens Changing the IEEE 802.1p to switch queue mapping may result in unexpected queuing behavior. This is because even if you change the mapping between the IEEE 802.1p priorities and the switch queues, the system still uses the same mapping between the switch queues and the IPQoS profile queues.
Page 376 Chapter 13 Profile Screens Figure 234 IPQoS Profile Screen 1 PVC 8 Queues Example 1b In the Name field, type “1PVC_8Queues”. 1c In the Number of Queues field, select 8. 1d Click Apply. 2 Apply the IPQoS Profile to Port 1 2a In the navigation panel, click Port >...
Page 377 Chapter 13 Profile Screens Figure 236 Config Save Screen 13.23.3.2 ADSL Mode: 3 PVCs for Triple Play Using SPQ Example This example uses 3 PVCs to support triple play service. Strict priority queuing helps ensure voice and video work properly. The backbone network and the system use IEEE 802.1Q VID 1 for voice, VID 2 for video, and VID 3 for data.
Page 378 Chapter 13 Profile Screens Table 166 PVC and IPQoS Profile Settings IPQoS Profile Level 0/33 Voice 4.096 Mbps 2 Mbps 0/34 Video 10.24 Mbps 5.12 Mbps 0/35 Data 5.12 Mbps 2.56 Mbps Here’s how to configure port 2 to use these settings. 1 VDSL Profile Setup 1a In the navigation panel, click Profile >...
Page 379 Chapter 13 Profile Screens Type “7” in the Level field. 2g Click Apply. 3 Configure the Video IPQoS Profile 3a In the navigation panel, click Profile > IPQoS to open the IPQoS Profile screen. Figure 240 Video IPQoS Profile 3b In the Name field, type “Video”. 3c In the Number of Queues field, select 1.
Page 380 Chapter 13 Profile Screens Figure 242 VDSL Port Setup Screen 3 PVCs SPQ Example 5b Select the slot where the line card is installed and port 2. Click Load. 5c In the IPQoS Profile field, select “20M_1M”. In the field to the right, select adsl2+.
Page 381 Chapter 13 Profile Screens 7 Create PVC 0/34 and Apply the Video IPQoS Profile 7a In the navigation panel, click Port > PVC to open the PVC Setup screen. 7b Select the slot where the line card is installed and port 2. Click Load. Figure 244 Video PVC Setup Screen PVC 0/34 7c In the VPI/VCI fields, enter “0”...
Page 382 Chapter 13 Profile Screens 8 Create PVC 0/35 and Apply the Data IPQoS Profile 8a In the navigation panel, click Port > PVC to open the PVC Setup screen. 8b Select the slot where the line card is installed and port 2. Click Load. Figure 245 Data PVC Setup Screen PVC 0/35 8c In the VPI/VCI fields, enter “0”...
Page 383 Chapter 13 Profile Screens 13.23.3.3 ADSL Mode: 2 PVCs in WRR Example In this example the subscriber is located farther away so there will often be less bandwidth actually available. 2 PVCs and WRR help ensure that both video and data traffic get through. The backbone network and the system use IEEE 802.1Q VID 2 for video and VID 3 for data.
Page 384 Chapter 13 Profile Screens 1 VDSL Profile Setup 1a In the navigation panel, click Profile > VDSL to open the VDSL Profile screen. Figure 248 VDSL Profile Screen 2 PVCs WRR Example 1b In the Name field, type “20M_1M”. 1c Type “1000” in the Up Stream Max Rate field and “20000” in the Down Stream Max Rate field.
Page 385 Chapter 13 Profile Screens Figure 250 Data_WRR IPQos Profile 3b In the Name field, type “Data_WRR”. 3c In the Number of Queues field, select 1. 3d In the PIR field, type 5120. 3e In the CIR fields, type 2560. Leave “0” in the Level field. 3g Type “40”...
Page 386 Chapter 13 Profile Screens 5 Create PVC 0/34 and Apply the Video_WRR IPQoS Profile 5a In the navigation panel, click Port > PVC to open the PVC Setup screen. 5b Select the slot where the line card is installed and port 3. Click Load. 5c Click Delete.
Page 387: Ipqos Profile Screen
Chapter 13 Profile Screens Figure 254 Config Save Screen 13.23.4 IPQoS Profile Screen Click Profile > IPQoS in the navigation panel to open the following screen. Use this screen to configure QoS (Quality of Service) profile setting for each traffic queue. Use the top part of the screen to add or edit IPQoS profiles.
Page 388: Reference: Ipqos And Modified Ieee 802.1P To Switch Queue Mapping
Chapter 13 Profile Screens Table 168 IPQoS Profile (continued) LABEL DESCRIPTION CIR is Committed Information Rate. Enter the maximum data rate (64~65532 kbps) guaranteed to flow through this device all the time. You must enter the number which is a multiple of 64.
Page 389: Access Control List (Acl) Overview
Chapter 13 Profile Screens This example maps the IEEE 802.1p priorities to only 4 switch queues. Since switch queue 3 is always mapped to IPQoS Q0, if you map IEEE 802.1p priority 7 to switch queue 3, and set 2 IPQoS queues, the system maps all of the IEEE 802.1p priorities to Q0 and does not use Q1. Table 169 IEEE 802.1p to IPQoS Modified Queue Mapping Example IEEE 802.1p Switch...
Page 390: Acl Profile Rules
Chapter 13 Profile Screens 13.24.1 ACL Profile Rules If you apply multiple profiles to a PVC, the system checks the profiles by rule number. The lower the rule number, the higher the priority the rule (and profile) has. For example, there are two ACL profiles assigned to a PVC.
Page 391 Chapter 13 Profile Screens Figure 256 ACL Profile Setup MSC1000G/1024G/1224G Series User’s Guide...
Page 392 Chapter 13 Profile Screens The following table describes the labels in this screen. Table 171 ACL Profile Setup LABEL DESCRIPTION Name Enter a descriptive name for the ACL profile. The name can be 1-31 printable ASCII characters long. Spaces are not allowed. Rule Select which type of rule to use.
Page 393: Rate Limit Profile Setup Screen
Chapter 13 Profile Screens 13.26 Rate Limit Profile Setup Screen Use this screen to set up Ethernet subscriber line transmission rate profiles. You apply the rate limit profiles to individual Ethernet line card ports (see Section 11.28 on page 291). To open this screen, click Profile >...
Page 394: Voip Dial Plan Profile Screen
Chapter 13 Profile Screens 13.27 VoIP Dial Plan Profile Screen The system uses dial plans to identify specific types of phone numbers dialed by a user, and to process the number before transmission by deleting or adding digits according to the relevant rule.
Page 395: Alarm E1 Profile Screen
Chapter 13 Profile Screens Table 173 Profile > Dialplan LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non- volatile memory when you are done configuring.
Page 396 Chapter 13 Profile Screens The following table describes the fields in this screen. Table 174 Alarm E1 Profile LABEL DESCRIPTION The top part of the screen is for profile configuration. Name Type a name to identify the alarm profile (you cannot change the name of the DEFVAL profile).
Page 397: Statistics Screens
H A P T E R Statistics Screens This chapter describes the run-time statistics. 14.1 ARP Table Address Resolution Protocol (ARP) is a protocol for mapping an Internet Protocol address (IP address) to a physical machine address, also known as a Media Access Control or MAC address, on the local area network.
Page 398: Dhcp
Chapter 14 Statistics Screens Figure 260 ARP Table The following table describes the labels in this screen. Table 175 ARP Table LABEL DESCRIPTION Total X ARP This displays the number of entries in the ARP table. Entries Flush Click Flush to remove all of the entries from the ARP table. Index This is the ARP table entry number.
Page 399: Mac Table
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 176 DHCP Statistics LABEL DESCRIPTION Slot Select the number of a line card’s slot. Port Select the number of a DSL port on the line card. Load Click Load to retrieve the port’s IGMP filter profile setting and display it in the Profile drop-down list box.
Page 400: Mac Table Screen
Chapter 14 Statistics Screens Figure 262 MAC Table Filtering Flowchart 14.5 MAC Table Screen Click Statistics > MAC Table in the navigation panel to display the following screen. This screen lists device MAC addresses that the system dynamically learned. Figure 263 MAC Table The following table describes the labels in this screen.
Page 401: Igmp Status Screen
Chapter 14 Statistics Screens Table 177 MAC Table (continued) LABEL DESCRIPTION Total Mac This is the total number of connected MAC addresses that the system has learned are connected. Index This is the number of the MAC table entry. This is the VLAN group to which the device belongs. MAC Address This is the MAC address of the device that the system has learned is connected to the port.
Page 402: Igmp Port Statistics
Chapter 14 Statistics Screens Table 178 IGMP Status (continued) LABEL DESCRIPTION Number Of This is the number of IGMP groups that the system has identified on the local IGMP Groups network. Query These are the total numbers of incoming, outgoing, and discarded Query packets. Report These are the total numbers of incoming, outgoing, and discarded Report packets.
Page 403: Ip Bridge Arp Proxy Screen
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 179 IGMP Status: Port Status LABEL DESCRIPTION Slot/Port Select a line card and line card port and click Load to show information. Flush Click Flush to reset the counters. Group Count This is the number of IGMP groups that the port is a member of.
Page 404: Ip Bridge Interfaces Screen
Chapter 14 Statistics Screens Table 180 IP Bridge ARP Proxy (continued) LABEL DESCRIPTION Slot This field displays the number of the slot that contains the line card with the port number to which the device is connected. Port This field displays the line card’s port number to which the device is connected. This field displays the Virtual Path Identifier (VPI) the device is using.
Page 405: Ip Bridge Routes Screen
Chapter 14 Statistics Screens Table 181 IP Bridge Interfaces (continued) LABEL DESCRIPTION Port This field displays the line card’s port number to which the device is connected. It displays “-” if the system looks for the subscriber in the whole VLAN and not a specific PVC.
Page 406: Online Users Screen
Chapter 14 Statistics Screens Table 182 IP Bridge Routes (continued) LABEL DESCRIPTION Priority This field displays the priority value (0 to 7) to add to incoming frames without a (IEEE 802.1p) priority tag. It displays “-” if the field does not apply to the entry (for example, in entries created automatically by the system).
Page 407: Msc Port Statistics
Chapter 14 Statistics Screens Figure 270 Port Statistics The following table describes the labels in this screen. Table 184 Port Statistics LABEL DESCRIPTION This column lists the slot numbers of the cards. Click the ID number of an active card to go to a screen where you can view port status and statistics. State This field displays the line card’s current operational status.
Page 408: Detailed Msc Ethernet Port Statistics
Chapter 14 Statistics Screens Figure 271 MSC Port Statistics: ENET The following table describes the labels in this screen. Table 185 MSC Port Statistics: ENET LABEL DESCRIPTION Flush Select a port or slot and click Flush to reset its counters. Slot/Port This field displays the port name or slot number.
Page 409 Chapter 14 Statistics Screens Figure 272 MSC Port Statistics: ENET Details The following table describes labels in this example. Table 186 MSC Port Statistics: ENET Details LABEL DESCRIPTION Status This shows whether or not the port has an active connection. Rate This shows the connection speed for an active connection.
Page 410: Msc Rmon Statistics
Chapter 14 Statistics Screens Table 186 MSC Port Statistics: ENET Details (continued) LABEL DESCRIPTION BCastPkts This is the number of good broadcast frames received/transmitted of 64 to 1518 octets in length (for non VLAN) or 1522 octets (for VLAN), not including multicast frames.
Page 411 Chapter 14 Statistics Screens Figure 273 MSC Port Statistics: ENET: RMON The following table describes the labels in this screen. Table 187 MSC Port Statistics: ENET: RMON LABEL DESCRIPTION sub1~up2 These are the Ethernet ports on the front panel of the MSC card. Click one to view RMON history information for that port.
Page 412 Chapter 14 Statistics Screens Table 187 MSC Port Statistics: ENET: RMON (continued) LABEL DESCRIPTION 65to127Octets This is the number of frames received/transmitted (including bad frames) that were 65 to 127 octets in length (this includes FCS octets but excludes framing bits).
Page 413: Dsl Line Card Statistics
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 188 Port Statistics: ENET: RMON History LABEL DESCRIPTION Interval Click Apply to use the selected data sampling time. Refresh Click Refresh to update this screen. SampleIndex This field display the index number.
Page 414 Chapter 14 Statistics Screens Figure 276 Port Statistics: DSL Line Card The following table describes the labels in this screen. Table 189 Port Statistics: DSL Line Card LABEL DESCRIPTION Port This field displays the port number. Link This field displays the port link status. On an SHDSL port, this field displays the wire pair setting when the port is up.
Page 415 Chapter 14 Statistics Screens Figure 277 Port Statistics: DSL Line Card: Packet Counter The following table describes the labels in this screen. Table 190 Port Statistics: DSL Line Card: Packet Counter LABEL DESCRIPTION Flush Click Flush to clear the counters. Link This field displays the port link status.
Page 416 Chapter 14 Statistics Screens Table 190 Port Statistics: DSL Line Card: Packet Counter (continued) LABEL DESCRIPTION IfUnknownProtos This field displays the number of packets received/transmitted with unknown protocol number on this port. Poll Interval(s) The text box displays how often (in seconds) this screen refreshes. You may change the refresh interval by typing a new number in the text box and then clicking Set Interval.
Page 417 Chapter 14 Statistics Screens Table 191 Port Statistics: DSL Line Card: Cell Counter (continued) LABEL DESCRIPTION Poll Interval(s) The text box displays how often (in seconds) this screen refreshes. You may change the refresh interval by typing a new number in the text box and then clicking Set Interval.
Page 418 Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 192 Port Statistics: DSL Line Card: Line Detail LABEL DESCRIPTION Flush Click Flush to clear the counters. Line Information Link This displays the connection status of the DSL link. Service Type This is the DSL standard that the port is using.
Page 419 Chapter 14 Statistics Screens Table 192 Port Statistics: DSL Line Card: Line Detail (continued) LABEL DESCRIPTION VTUR Serial This field displays the name of the CPE VDSL device serial number. Line Performance FeCrc This is the number of far end cyclic redundancy checks. NeCrc This is the number of near end cyclic redundancy checks.
Page 420 Chapter 14 Statistics Screens Figure 280 Port Statistics: DSL Line Card: Line Performance: Current The following table describes the labels in this screen. Table 193 Port Statistics: DSL Line Card: Line Performance: Current LABEL DESCRIPTION Flush Click Flush to clear the counters. PhysEntry CurrSnrMgn (dB) These are the DSL line’s current downstream and upstream signal to noise...
Page 421 Chapter 14 Statistics Screens Table 193 Port Statistics: DSL Line Card: Line Performance: Current (continued) LABEL DESCRIPTION CurrAttainableRate These are the DSL line’s current downstream and upstream attainable rates in decibels. ChanEntry ChanInterleaveDelay These are the numbers of milliseconds of interleave delay for downstream and (ms) upstream transmissions.
Page 422 Chapter 14 Statistics Screens Table 193 Port Statistics: DSL Line Card: Line Performance: Current (continued) LABEL DESCRIPTION SESs (seconds) This is the number of Severely Errored Seconds. This is how many seconds contained 30% or more errored blocks or at least one defect. This is a subset of Es.
Page 423 Chapter 14 Statistics Screens Table 194 Port Statistics: DSL Line Card: Line Performance: 15Min (continued) LABEL DESCRIPTION Lols (seconds) This is the DSL line’s downstream number of Loss of link Seconds that have occurred for the past 15 minute period. This is the number of times the DSL line’s downstream connection has experienced a Loss of link during the past 15 minute period.
Page 424 Chapter 14 Statistics Screens Figure 282 Port Statistics: DSL Line Card: Line Performance: 1day 14.11.4.7 DSL Line Status To display line information for an active ADSL line, click the port number in the line card’s statistics screen (see Figure 276 on page 414) and click the Status tab.
Page 425: Elc Port Statistics
Chapter 14 Statistics Screens Figure 283 Port Statistics: DSL Line Card: Status The following table describes the labels in this screen. Table 195 Port Statistics: DSL Line Card: Status LABEL DESCRIPTION Items Select a type of line information to display linedata: Displays an ADSL port's line bit allocation.
Page 426: Detailed Elc Port Statistics
Chapter 14 Statistics Screens Figure 284 ELC Port Statistics The following table describes the labels in this screen. Table 196 ELC Port Statistics LABEL DESCRIPTION Port This field displays the slot number. Click one of these links to see detailed Ethernet port statistics.
Page 427: Vop Port Statistics
Chapter 14 Statistics Screens Figure 285 ELC Port Statistics Details The following table describes labels in this example. Table 197 ELC Port Statistics Details LABEL DESCRIPTION Flush Click Flush to clear the counters. Packet Counter Rate (kbps) This field displays the number of kilobits received/transmitted on this port per second.
Page 428: Detailed Vop Port Statistics
Chapter 14 Statistics Screens Figure 286 VOP Port Statistics The following table describes the labels in this screen. Table 198 VOP Port Statistics LABEL DESCRIPTION Port This field displays the port number. Click one of these links to see detailed Ethernet port statistics.
Page 429 Chapter 14 Statistics Screens Figure 287 VOP Port Statistics Details The following table describes labels in this example. Table 199 VOP Port Statistics Details LABEL DESCRIPTION Refresh Click Refresh to update this screen. Line Status Service Status This field displays the current state of the analog phone port. Possible values are: Disabled Out-of-service...
Page 430: Ima Line Card Statistics
Chapter 14 Statistics Screens Table 199 VOP Port Statistics Details (continued) LABEL DESCRIPTION SIP Local URI This is the Universal Resource Indicator of the port. If a local URI is “aaa@bbb”, “aaa” is the telephone number configured in the VoIP >...
Page 431 Chapter 14 Statistics Screens Figure 288 Port Statistics: IMA Line Card The following table describes the labels in this screen. Table 200 Port Statistics: IMA Line Card LABEL DESCRIPTION Port This field displays the port number. Admin State This field displays whether the port is activated (In of Service) or not (notInService).
Page 432 Chapter 14 Statistics Screens Table 200 Port Statistics: IMA Line Card (continued) LABEL DESCRIPTION Poll Interval(s) The text box displays how often (in seconds) this screen refreshes. You may change the refresh interval by typing a new number in the text box and then clicking Set Interval.
Page 433 Chapter 14 Statistics Screens 14.11.9.2 E1 Link Performance - Current Day To display the link performance of a port on the IMA line card for the current day, click the port number in the line card’s statistics screen (see Figure 288 on page 431) and click the Currday tab.
Page 434 Chapter 14 Statistics Screens Figure 291 Port Statistics: IMA Line Card: E1 Performance - Last24hr The following table describes the labels in this screen. Table 203 Port Statistics: IMA Line Card: E1 Performance - Last24hr LABEL DESCRIPTION Refresh Click this to update this screen. PerfLast24HR The following parameters are used to evaluate this port’s performance in the last 24 hours.
Page 435 Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 204 Port Statistics: IMA Line Card: E1 Performance - 96Quarter LABEL DESCRIPTION Start quarter Enter the starting quarter hour between 1 to 96. End quarter Enter the ending quarter hour between 1 to 96. This ending quarter hours must be equal to or grater than the starting quarter hours.
Page 436: Dot3Ad
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 205 Port Statistics: IMA Line Card: E1 Performance - 7Day LABEL DESCRIPTION Start day Enter the starting day within the past 7 days between 1 to 7. End day Enter the ending day within the past 7 days between 1 to 7.
Page 437: Vlan Statistics
Chapter 14 Statistics Screens Table 206 Dot3ad (continued) LABEL DESCRIPTION State This field displays whether link aggregation is activated on the ports. Members This field displays the name of the link aggregation group. Links These are the ports you have configured to be in the trunk group. Syncs These are the ports that are currently transmitting data as one logical link in this trunk group.
Page 438: Mstp Statistics
Chapter 14 Statistics Screens Figure 296 VLAN: Port Status The following table describes the labels in this screen. Table 208 VLAN: Port Status LABEL DESCRIPTION VID X This field displays the VLAN ID. Index This field displays the index number. Card Name This field displays the name of the line card in this VLAN.
Page 439 Chapter 14 Statistics Screens Figure 297 MSTP Statistics: CIST The following table describes the labels in this screen. Table 209 MSTP Statistics: CIST LABEL DESCRIPTION Enable This field displays whether MSTP is activated on the device. BridgeID This is the unique identifier for this bridge, consisting of bridge priority plus MAC address.
Page 440: Mstp Cist Statistics: Port Details
Chapter 14 Statistics Screens Table 209 MSTP Statistics: CIST (continued) LABEL DESCRIPTION ExtRootForwardDelay This is the time (in seconds) the root bridge will wait before changing states (that is, listening to learning or learning to forwarding) on the root port. Each change in states requires the forward delay time before the change.
Page 441: Mstp Msti Statistics
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 210 MSTP Statistics: CIST: Port Details LABEL DESCRIPTION Enable This field displays whether MSTP is activated on the device. Uptime This field displays the time the port is running. State This field displays the STP status on this port.
Page 442 Chapter 14 Statistics Screens Figure 299 MSTP Statistics: MSTI The following table describes the labels in this screen. Table 211 MSTP Statistics: MSTI LABEL DESCRIPTION MSTID Select an MSTI number and click Apply to display the port status for that spanning tree instance.
Page 443: Ip Statistics
Chapter 14 Statistics Screens 14.15 IP Statistics To view management IP settings and statistics, click Statistics > IP in the navigation panel. Figure 300 IP Statistics The following table describes the labels in this screen. Table 212 IP Statistics LABEL DESCRIPTION Flush Click Flush to reset the counters for the selected port.
Page 444: G.bond Statistics
Chapter 14 Statistics Screens Table 212 IP Statistics (continued) LABEL DESCRIPTION Out Error This field displays the number of errored packets transmitted on this port. Out Unknown This field displays the number of packets with an unknown source transmitted on this port.
Page 445: Interface Statistics
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 214 CFM Statistics LABEL DESCRIPTION MD, MA, Endpoint Use the drop-down boxes to select an MD, MA, and end point ID for which you want to see a CFM statistics report. Load Click Load to display the available CFM end points based on your selected criteria.
Page 446: Media Interface Statistics
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 215 H.248 Interface Statistics LABEL DESCRIPTION Click the number of an H.248 interface to view information about its media gateway cards. MG State This is the H.248 interface’s current media gateway status (registering, registered, disconnected, or disable).
Page 447: Media Card Statistics
Chapter 14 Statistics Screens Table 216 H.248 Media Interface Statistics (continued) LABEL DESCRIPTION Management This is the out-of-band IP address of the MSC in the same chassis as the media Outband IP card. Port Count This shows the number of configured subscriber port on the media card. 14.18.2 H.248 Media Card Statistics To view a H.248 media card’s statistics, click Statistics >...
Page 448: Termination Statistics
Chapter 14 Statistics Screens Figure 306 Proxy Server Statistics The following table describes the labels in this screen. Table 218 Proxy Server Statistics LABEL DESCRIPTION Slot Select the slot number of a SIP VOP card. Click Load to show the card’s list of SIP proxy servers and their status.
Page 449: Sfp Details
Chapter 14 Statistics Screens Table 219 Termination Statistics (continued) LABEL DESCRIPTION Slot ID This is the number of the slot containing the VoIP card. Port Count This is the number of ports on the VoIP card. Card State This is the media card’s current status in relation to the signaling card (unregistered, registered, invalid, or unknown).
Page 450: Oam Statistics
Chapter 14 Statistics Screens Table 220 SFP Statistics (continued) LABEL DESCRIPTION Revision This is the revision level for the part number provided by the transceiver vendor. SerialNumber This is the serial number provided by the transceiver vendor. 14.22 OAM Statistics To view Ethernet OAM (Operational, Administration and Maintenance) details about an Ethernet line card port, click Statistics >...
Page 451: Ima Statistics
Chapter 14 Statistics Screens Table 221 OAM Statistics (continued) LABEL DESCRIPTION Parser State This field indicates the current state of the parser. Forward: The packet is forwarding packets normally. Loopback: The port is in loopback mode. Discard: The port is discarding non-OAMPDUs because it is trying to or has put the remote device into loopback mode.
Page 452: Ima Group Statistics
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 222 IMA Statistics LABEL DESCRIPTION This is the slot number of an IMA line card. Click the index number of an active line card to display a screen that lists the current status for each port on the line card.
Page 453: Ima Group Details
Chapter 14 Statistics Screens Table 223 IMA Statistics: IMA Line Card (continued) LABEL DESCRIPTION Test Processing Status This field displays whether the test pattern procedure is enabled or disabled on this link and whether any links failed in the test. TimeElapsed(secs) This field displays the number of seconds that have elapsed since the last data collection.
Page 454 Chapter 14 Statistics Screens Figure 312 IMA Statistics: IMA Line Card: Group Detail MSC1000G/1024G/1224G Series User’s Guide...
Page 455 Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 224 IMA Statistics: IMA Line Card: Group Detail LABEL DESCRIPTION Link This displays the connection status of the E1 link. Click the number of a link to view its details.
Page 456: Link Details
Chapter 14 Statistics Screens Table 224 IMA Statistics: IMA Line Card: Group Detail (continued) LABEL DESCRIPTION Unavailable This field displays the number of the unavailable seconds for this IMA group. Seconds (secs) Ne Num Failures This field displays the number of times a failure on this IMA group has been reported by the IMA line card since it was booted up.
Page 457 Chapter 14 Statistics Screens Figure 313 IMA Statistics: IMA Line Card: Group Detail: Link Detail The following table describes the labels in this screen. Table 225 IMA Statistics: IMA Line Card: Group Detail: Link Detail LABEL DESCRIPTION RelDelay(ms) This field displays the least delay in milliseconds measured most recently on this link compared to the other links in the same IMA group.
Page 458: Link 15Min
Chapter 14 Statistics Screens Table 225 IMA Statistics: IMA Line Card: Group Detail: Link Detail (continued) LABEL DESCRIPTION Test Processing The field displays the current state of the Test Pattern Procedure. Status disabled: The test is stopped. operating: The test is running and no error has been detected on the link. linkFail: An error has been detected on this link during the test.
Page 459 Chapter 14 Statistics Screens Figure 314 IMA Statistics: IMA Line Card: Group Detail: Link 15Min The following table describes the labels in this screen. Table 226 IMA Statistics: IMA Line Card: Group Detail: Link 15Min LABEL DESCRIPTION Refresh Click this to update this screen. Flush Click this to clear the counters in this screen.
Page 460: Link 1Day
Chapter 14 Statistics Screens 14.23.5 Link 1Day To display the performance of an E1 link on the selected IMA group for the current day, click the slot number in the Statistics > IMA screen, the index number of the IMA group (see Figure 311 on page 452) and then the number of a link and the Link 1Day tab.
Page 461: Link Last24Hr
Chapter 14 Statistics Screens Table 227 IMA Statistics: IMA Line Card: Group Detail: Link 1Day (continued) LABEL DESCRIPTION UUSFE(secs) This is the number of unusable seconds in the transmission (Tx) or receiving (Rx) direction detected by the remote IMA device. Stuff This is the number of stuff events the IMA line card has inserted on the link in the transmission (Tx) or receiving (Rx) direction.
Page 462: Link 96Q
Chapter 14 Statistics Screens Table 228 IMA Statistics: IMA Line Card: Group Detail: Link Last24hr (continued) LABEL DESCRIPTION UASFE(secs) This is unavailable seconds detected by the remote IMA device. This is the number of link-layer transmission (Tx) or receiving (Rx) failures detected by the IMA line card.
Page 463: Link 7Day
Chapter 14 Statistics Screens The following table describes the labels in this screen. Table 229 IMA Statistics: IMA Line Card: Group Detail: Link 96Q LABEL DESCRIPTION Start quarter Enter the starting quarter hour between 1 to 96. End quarter Enter the ending quarter hour between 1 to 96. This ending quarter hours must be equal to or grater than the starting quarter hours.
Page 464 Chapter 14 Statistics Screens Figure 318 IMA Statistics: IMA Line Card: Group Detail: Link 7Day The following table describes the labels in this screen. Table 230 IMA Statistics: IMA Line Card: Group Detail: Link 7Day LABEL DESCRIPTION Start day Enter the starting day within the past 7 days between 1 to 7. End day Enter the ending day within the past 7 days between 1 to 7.
Page 465: Ima Group Performance - Current 15 Minutes
Chapter 14 Statistics Screens Table 230 IMA Statistics: IMA Line Card: Group Detail: Link 7Day (continued) LABEL DESCRIPTION UUS(secs) This is the number of unusable seconds in the transmission (Tx) or receiving (Rx) direction detected by the IMA line card. UUSFE(secs) This is the number of unusable seconds in the transmission (Tx) or receiving (Rx) direction detected by the remote IMA device.
Page 466: Ima Group Performance - Last 24 Hours
Chapter 14 Statistics Screens Figure 320 IMA Statistics: IMA Line Card: Group 1Day The following table describes the labels in this screen. Table 232 IMA Statistics: IMA Line Card: Group 1Day LABEL DESCRIPTION Refresh Click this to update this screen. Flush Click this to clear the counters.
Page 467: Ima Group Performance - Last 96 Quarter Hours
Chapter 14 Statistics Screens Table 233 IMA Statistics: IMA Line Card: Group Last24hr (continued) LABEL DESCRIPTION NE-Failures This field displays the number of upstream failures detected in this IMA group within the last 24 hours. FE-Failures This field displays the number of downstream failures detected in this IMA group within the last 24 hours.
Page 468: Ima Group Performance - Last 7 Days
Chapter 14 Statistics Screens Table 234 IMA Statistics: IMA Line Card: Group 96Q (continued) LABEL DESCRIPTION Page X of X This identifies which page of information is displayed and the total number of pages of information. Next Click Next to show the following screen if the information cannot be displayed in one screen.
Page 469: Ima Line Card Cell Counters
Chapter 14 Statistics Screens Table 235 IMA Statistics: IMA Line Card: Group 7Day (continued) LABEL DESCRIPTION Page X of X This identifies which page of information is displayed and the total number of pages of information. Next Click Next to show the following screen if the information cannot be displayed in one screen.
Page 470: Loop Guard Statistics
Chapter 14 Statistics Screens Figure 325 IMA Statistics: IMA Line Card: Pkt Counter The following table describes the labels in this screen. Table 237 IMA Statistics: IMA Line Card: Pkt Counter LABEL DESCRIPTION vpi, vci Enter the VPI and VCI of a channel on the IMA group and then click Load to display the packet counters.
Page 471 Chapter 14 Statistics Screens Figure 326 Statistics > Loop Guard The following table describes the labels in this screen. Table 238 Statistics > Loop Guard LABEL DESCRIPTION Slot Select a card’s slot number and click Load to display the cards loop guard. Port No.
Page 472 Chapter 14 Statistics Screens MSC1000G/1024G/1224G Series User’s Guide...
Page 473: Switch Screens
H A P T E R Switch Screens This chapter describes the screens you use to configure Ethernet ports, multicast VLAN and global switch parameters such as GARP, link aggregation, priority queues and queuing method. 15.1 Ethernet Port Trunking Ethernet port trunking lets you aggregate the Ethernet ports into one logical link. The switch uses MAC-based load balancing which analyzes a packet’s source and destination MAC addresses to distribute the load between the two Ethernet ports when uplinking to the remote switch.
Page 474: Link Aggregation Id
Chapter 15 Switch Screens • LACP only works on full-duplex links. • All ports in the same trunk group must have the same media type, speed, duplex mode and flow control settings. Configure trunk groups or LACP before you connect the Ethernet switch to avoid causing network topology loops.
Page 475: Strict Priority Queuing (Spq)
Chapter 15 Switch Screens 15.4.1 Strict Priority Queuing (SPQ) Strict Priority Queuing (SPQ) services queues based on priority only. As traffic comes into the switch, traffic on the highest priority queue, Q7 is transmitted first. When that queue empties, traffic on the next highest-priority queue, Q6 is transmitted until Q6 empties, and then traffic is transmitted on Q5 and so on.
Page 476 Chapter 15 Switch Screens The following table describes the labels in this screen. Table 242 Switch Setup General LABEL DESCRIPTION GARP Timer: Switches join VLANs by making a declaration. A declaration is made by issuing a Join message using GARP. Declarations are withdrawn by issuing a Leave message. A Leave All message terminates all registrations.
Page 477: Switch Setup Dot3Ad Screen
Chapter 15 Switch Screens 15.6 Switch Setup Dot3ad Screen Click Switch > Switch Setup > Dot3ad to display the screen as shown. Figure 328 Switch Setup Dot3ad The following table describes the labels in this screen. Table 243 Switch Setup Dot3ad LABEL DESCRIPTION LACP Priority...
Page 478: Switch Setup Qschedule Screen
Chapter 15 Switch Screens Table 243 Switch Setup Dot3ad (continued) LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 479: Switch Setup Isolation Screen
Chapter 15 Switch Screens 15.8 Switch Setup Isolation Screen Click Switch > Switch Setup > Isolation to display the screen as shown. Figure 330 Switch Setup Isolation The following table describes the labels in this screen. Table 245 Switch Setup Isolation LABEL DESCRIPTION Port Isolation...
Page 480: Spanning Tree Protocols
Chapter 15 Switch Screens Table 245 Switch Setup Isolation (continued) LABEL DESCRIPTION Select Select an entry’s Select check box and click Delete to remove the entry. Clicking Delete saves your changes to the MSC’s volatile memory. The MSC loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non-volatile memory when you are done configuring.
Page 481 Chapter 15 Switch Screens Table 247 MSTP/RSTP Path Costs LINK ALLOWED RECOMMENDED VALUE RECOMMENDED RANGE SPEED RANGE 10 Mbps 2 000 000 200 000 to 20 000 000 1 to 200 000 000 100 Mbps 200 000 20 000 to 2 000 000 1 to 200 000 000 1 Gbps 20 000...
Page 482: Multiple Stp
Chapter 15 Switch Screens In STP, once a stable network topology has been established, all devices listen for Hello BPDUs transmitted from the root bridge. If an STP-aware device does not get a Hello BPDU after a predefined interval (Max Age), the device assumes that the link to the root bridge is down.
Page 483 Chapter 15 Switch Screens Figure 332 STP/RSTP Network Example With MSTP, VLANs 1 and 2 are mapped to different spanning trees in the network. Thus traffic from the two VLANs travel on different paths. The following figure shows the network example using MSTP.
Page 484 Chapter 15 Switch Screens • VLAN-to-MST mapping 15.9.2.3 MST Instance An MST Instance (MSTI) is a set of VLANs that use the same spanning tree. Each created MSTI is identified by a unique number (known as an MST ID) known internally to a region. Thus an MSTI does not span across MST regions.
Page 485: Mstp Setup
Chapter 15 Switch Screens 15.10 MSTP Setup Use the MSTP screens to enable MSTP on the switch and configure MSTP bridge and port settings. 15.10.1 MSTP Bridge Settings Click Switch > MSTP in the navigation panel to display the screen shown next. Use this screen to configure MSTP and RSTP settings.
Page 486 Chapter 15 Switch Screens Table 249 MSTP: Bridge (continued) LABEL DESCRIPTION Enable Select this option to activate MSTP on the system. Priority Priority is used in determining the root switch. The switch with the highest priority (lowest numeric value) becomes the STP root switch. If all switches have the same priority, the switch with the lowest MAC address will then become the root switch.
Page 487: Mstp Port Settings
Chapter 15 Switch Screens Table 249 MSTP: Bridge (continued) LABEL DESCRIPTION MSTID This field displays the ID of an MST instance. This field displays the VID (or VID ranges) to which the MST instance is mapped. Config Digest A configuration digest is generated from the VLAN-MSTI mapping information. This field displays the 16-octet signature that is included in an MSTP BPDU.
Page 488: Mstp Configuration Example
Chapter 15 Switch Screens Table 250 MSTP: Port (continued) LABEL DESCRIPTION Set a point-to-point link between ports to increase the speed of convergence by allowing the network to determine the designated port faster. The port must be connected directly to another switch port. Select Enable to activate this feature on a full-duplex port that is connected directly to another switch port.
Page 489 Chapter 15 Switch Screens Figure 339 MSTP Configuration Example: Bridge 5 To configure port MSTP settings, click the Port tab. 6 Select the instance ID number in the MSTID field and click Apply. 7 Select Enable to set the port to belong to this spanning tree and click Apply. For this network example, enable uplink ports 1 and 2 in the two spanning tree instances (MSTID 1 and 2).
Page 490: Switch Port
Chapter 15 Switch Screens Figure 340 MSTP Configuration Example: Port 8 For switch B, configure the same general MSTP settings and VLAN-to-MST mappings as switch A for the subtending ports. 9 Set the subtending port priorities on switch B to allow MSTP to forward traffic to the corresponding link.
Page 491: Port Vlan Trunking
Chapter 15 Switch Screens The MSC uses IEEE 802.3x flow control in full duplex mode and back pressure flow control in half duplex mode. IEEE 802.3x flow control is used in full duplex mode to send a pause signal to the sending port, causing it to temporarily stop sending signals when the receiving port memory buffers fill.
Page 492: Switch Port Setup Port Screen
Chapter 15 Switch Screens 15.12 Switch Port Setup Port Screen Click Switch > Switch Port Setup in the navigation panel to display the screen shown next. Use this screen to configure basic settings for the Gigabit Ethernet interfaces. Figure 342 Switch Port Setup The following table describes the labels in this screen.
Page 493: Switch Port Setup 802.1P/1Q Screen
Chapter 15 Switch Screens 15.13 Switch Port Setup 802.1P/1Q Screen Click Switch > Switch Port Setup > 802.1P/1Q in the navigation panel to display the screen shown next. Use this screen to configure IEEE 802.1p priority and IEEE 802.1Q VLAN settings for the Gigabit Ethernet interfaces.
Page 494: Switch Port Setup Broadcast Screen
Chapter 15 Switch Screens Figure 344 Switch Port Setup: Bandwidth The following table describes the labels in this screen. Table 253 Switch Port Setup: Bandwidth LABEL DESCRIPTION Port This is the label of a Gigabit Ethernet interface. Enable Select this check box to turn on bandwidth control for an interface. Ingress Rate Type a maximum bandwidth allowed for the incoming traffic flow on a port (measured in megabits per second).
Page 495: Switch Port Setup Dscp
Chapter 15 Switch Screens The following table describes the labels in this screen. Table 254 Switch Port Setup: Broadcast LABEL DESCRIPTION Port This is the label of a Gigabit Ethernet interface. Broadcast Select Enable to limit the number of broadcast packets the interface will accept per second.
Page 496 Chapter 15 Switch Screens Figure 346 Switch Port Setup: DSCP The following table describes the labels in this screen. Table 255 Switch Port Setup: DSCP LABEL DESCRIPTION Port This is the label of a Gigabit Ethernet interface. Enable Select Enable to map DSCP (priorities) for individual ports. Apply Click Apply to save the changes in this screen to the system’s volatile memory.
Page 497: Switch Cfm Screens
Chapter 15 Switch Screens 15.17 Switch CFM Screens Click Switch > CFM in the navigation panel to display the screen shown next. Use this screen for initial configuration of a CFM (Connectivity Fault Management) domain, to globally switch this feature on or off and to create an MD. Refer to Section 8.1 on page 175 for more information.
Page 498 Chapter 15 Switch Screens Figure 348 CFM Maintenance Association The following table describes the labels in this screen. Table 257 CFM Maintenance Association LABEL DESCRIPTION MD Name This displays the MD name which you want to configure MAs, endpoint IDs, VLAN IDs in this screen.
Page 499: Cfm Endpoint Screen: Mep
Chapter 15 Switch Screens Table 257 CFM Maintenance Association (continued) LABEL DESCRIPTION Apply Click Apply to add the settings as a new entry in the summary table above. Click New to start configuring an MA setting. Cancel Click Cancel to reset the fields. Add MEP ID Enter a remote MEP ID (1~8191) associated to this MA and allowed to be used in the CFM test.
Page 500: Cfm Endpoint Screen: Mip
Chapter 15 Switch Screens The following table describes the labels in this screen. Table 258 CFM Endpoint: MEP LABEL DESCRIPTION MD Name This displays the name of the MD for which you want to configure end points. MA Name This displays the name of the MA for which you want to configure end points. Endpoint ID Select a valid MEP ID which is defined in the CFM maintenance association screen.
Page 501 Chapter 15 Switch Screens Figure 350 CFM Endpoint: MIP The following table describes the labels in this screen. Table 259 CFM Endpoint: MIP LABEL DESCRIPTION MD Name This displays the name of the MD for which you want to configure end points. MA Name This displays the name of the MA for which you want to configure end points.
Page 502: Cfm Endpoint: Mip Slot Screen
Chapter 15 Switch Screens Table 259 CFM Endpoint: MIP (continued) LABEL DESCRIPTION State This field displays the line card’s current operational status. active means the line card is operating normally. init means the MSC is initializing the line card. disable means a manager has disabled the line card. inactive means the line card is starting up or is not operating normally.
Page 503: Switch Cfm Lbr Screen
Chapter 15 Switch Screens 15.17.5 Switch CFM LBR Screen Click Switch > CFM > LBR to display the screen shown next. Use this screen to enable or disable loopback testing on individual ports. LBR stands for Loop Back Response. Figure 352 Switch CFM > LBR The following table describes the labels in this screen.
Page 504: Switch Cfm Lbr Slot Screen
Chapter 15 Switch Screens Table 261 Switch CFM > LBR (continued) LABEL DESCRIPTION State This field displays the line card’s current operational status. active means the line card is operating normally. init means the MSC is initializing the line card. disable means a manager has disabled the line card.
Page 505: Switch Oam Setup
Chapter 15 Switch Screens 15.18 Switch OAM Setup To configure Ethernet OAM (Operational, Administration and Maintenance) settings for the Ethernet line card ports, click Switch > OAM. Figure 354 Switch > OAM The following table describes the labels in this screen. Table 263 Switch >...
Page 506 Chapter 15 Switch Screens Table 263 Switch > OAM (continued) LABEL DESCRIPTION Copy Do the following to copy settings from one Ethernet port to another Ethernet port or ports. 1. Use the Select column to choose an Ethernet port from which you want to copy settings.
Page 507: Sys Screens
H A P T E R Sys Screens This chapter describes the Sys screens you use to configure general system, access control, syslog, administrator login accounts and management IP settings. 16.1 SNMP Simple Network Management Protocol is a protocol used for exchanging management information between network switches.
Page 508: Supported Mibs
Chapter 16 Sys Screens The managed devices contain object variables/managed objects that define each piece of information to be collected about a switch. Examples of variables include such as number of packets received, node port status etc. A Management Information Base (MIB) is a collection of managed objects.
Page 509 Chapter 16 Sys Screens Figure 357 Access Control: SNMP The following table describes the labels in this screen. Table 265 Access Control: SNMP LABEL DESCRIPTION Get Community Enter the get community, which is the password for the incoming Get- and GetNext- requests from the management station.
Page 510: Service Access Control Screen
Chapter 16 Sys Screens Table 265 Access Control: SNMP (continued) LABEL DESCRIPTION User Information Configure the administrative login accounts for SNMP management. Use the User Account screen to create administrative login accounts. See Section 16.7 on page 516. Index This field displays the index number. Enable This field displays whether the administrative login account is activated or note.
Page 511: Secured Client Screen
Chapter 16 Sys Screens The following table describes the labels in this screen. Table 266 Access Control: Service Access Control LABEL DESCRIPTION Services These are services you may use to access the system are listed here. Enable Select the Enable check boxes for the corresponding services that you want to allow to access the system.
Page 512: General Setup
Chapter 16 Sys Screens The following table describes the labels in this screen. Table 267 Access Control: Secured Client LABEL DESCRIPTION Index This is the client set index number. A “client set” is a group of one or more “trusted computers”...
Page 513 Chapter 16 Sys Screens Figure 360 General Setup The following table describes the labels in this screen. Table 268 General Setup LABEL DESCRIPTION Host Name Choose a descriptive name for identification purposes. This name consists of up to 31 English keyboard characters; spaces are not allowed. Location Enter the geographic location of your system.
Page 514: Ip Setup
Chapter 16 Sys Screens Table 268 General Setup (continued) LABEL DESCRIPTION System Up Time This field shows how long the system has been running since the last time it was started. Database Version This field displays the time and date that the system’s configuration was last saved to the non-volatile memory.
Page 515: Syslog Screen
Chapter 16 Sys Screens Figure 361 IP Setup The following table describes the labels in this screen. Table 269 IP Setup LABEL DESCRIPTION Inband These fields configure in-band management settings. In-band management refers to accessing the management interface through a network port (not the management port).
Page 516: User Account Screen
Chapter 16 Sys Screens Figure 362 Unix Syslog The following table describes the labels in this screen. Table 270 Unix Syslog LABEL DESCRIPTION Enable Unix Select this check box to activate syslog (system logging) and then configure the Syslog syslog parameters described in the following fields. Facility1~7 The log facility allows you to send logs to different files in the syslog server.
Page 517: Monitor Screen
Chapter 16 Sys Screens The following table describes the labels in this screen. Table 271 User Account LABEL DESCRIPTION Enable Select this check box to activate the administrator account. Name Type a user name for the account Password Type a password for the account. Retype Password Type the password again to make sure you have entered it properly.
Page 518 Chapter 16 Sys Screens Figure 364 Sys > Monitor The following table describes the labels in this screen. Table 272 Sys > Monitor LABEL DESCRIPTION Slot Select the number of a card’s slot. Voltage(V) The power supply for each voltage has a sensor that can detect and report the voltage.
Page 519 Chapter 16 Sys Screens Table 272 Sys > Monitor (continued) LABEL DESCRIPTION high_lmt Use these fields to set the maximum voltage threshold for each sensor. The maximum voltage for each voltage sensor must be within the following ranges. Measured in millivolts (mV). MSC: 1 = 2575~2750, 2 = 1287~1375, 3 = 3399~3630, 4 = 1339~1430, 5 = 15450~16500 ADSL line card: 1 = 1236~1320, 2 = 1854~1980, 3 = 3399~3630, 4 =...
Page 520: Authentication, Authorization And Accounting
Chapter 16 Sys Screens Table 272 Sys > Monitor (continued) LABEL DESCRIPTION current This is the fan’s current RPM reading. high_lmt Use these fields to set the maximum RPM threshold for each sensor. The maximum RPM for each fan must be within 1000~8000. low_limit Use these fields to set the minimum RPM threshold for each sensor.
Page 521: Local User Accounts
Chapter 16 Sys Screens Figure 365 AAA Server Auth Server Client 16.9.1 Local User Accounts By storing user profiles locally on the system, your system is able to authenticate and authorize users without interacting with a network authentication server. However, there is a limit on the number of users you may authenticate in this way.
Page 522 Chapter 16 Sys Screens Figure 366 Sys > AAA The following table describes the labels in this screen. Table 274 Sys > AAA LABEL DESCRIPTION Authentication Use this section to specify the methods used to authenticate users accessing the system. Login These fields specify which database the system should use (first, second and third) to authenticate administrator accounts (users for system management).
Page 523: Radius Server Setup
Chapter 16 Sys Screens Table 274 Sys > AAA (continued) LABEL DESCRIPTION Active Select this to activate accounting for a specified event types. Broadcast Select this to have the system send accounting information to all configured accounting servers at the same time. If you don’t select this and you have two accounting servers set up, then the system sends information to the first accounting server and if it doesn’t get a response from the accounting server then it tries the second accounting server.
Page 524 Chapter 16 Sys Screens Figure 367 RADIUS Server Setup The following table describes the labels in this screen. Table 275 RADIUS Server Setup LABEL DESCRIPTION Authentication Use this section to configure your RADIUS authentication settings. Server Mode This field is only valid if you configure multiple RADIUS servers. Select index-priority and the system tries to authenticate with the first configured RADIUS server, if the RADIUS server does not respond then the system tries to authenticate with the second RADIUS server.
Page 525: Tacacs+ Server Setup
Chapter 16 Sys Screens Table 275 RADIUS Server Setup (continued) LABEL DESCRIPTION IP Address Enter the IP address of an external RADIUS accounting server in dotted decimal notation. UDP Port The default port of a RADIUS server for accounting is 1813. You need not change this value unless your network administrator instructs you to do so.
Page 526 Chapter 16 Sys Screens The following table describes the labels in this screen. Table 276 TACACS+ Server Setup LABEL DESCRIPTION Authentication Use this section to configure your TACACS+ authentication settings. Server Mode This field is only valid if you configure multiple TACACS+ servers. Select index-priority and the system tries to authenticate with the first configured TACACS+ server, if the TACACS+ server does not respond then the system tries to authenticate with the second TACACS+ server.
Page 527: Vendor Specific Attribute
Chapter 16 Sys Screens 16.9.6 Vendor Specific Attribute RFC 2865 standard specifies a method for sending vendor-specific information between a RADIUS server and a network access device (for example, the system). A company can create Vendor Specific Attributes (VSAs) to expand the functionality of a RADIUS server. The MSC supports VSAs that allow you to perform the following actions based on user authentication: •...
Page 528: Supported Radius Attributes
Chapter 16 Sys Screens 16.9.6.1 Tunnel Protocol Attribute You can configure tunnel protocol attributes on the RADIUS server (refer to your RADIUS server documentation) to assign a port on the system to a VLAN based on IEEE 802.1x authentication. The port VLAN settings are fixed and untagged. This will also set the port’s VID.
Page 529: Attributes Used For Accounting
Chapter 16 Sys Screens 16.10.1.3 Attributes Used by the IEEE 802.1x Authentication User-Name NAS-Identifier NAS-IP-Address NAS-Port NAS-Port-Type - This value is set to Ethernet(15) on the system. Calling-Station-Id Frame-MTU EAP-Message State Message-Authenticator 16.10.2 Attributes Used for Accounting The following sections list the attributes sent from the system to the RADIUS server when performing authentication.
Page 530 Chapter 16 Sys Screens Table 280 RADIUS Attributes - Exec Events via Telnet/SSH ATTRIBUTE START INTERIM-UPDATE STOP User-Name NAS-Identifier NAS-IP-Address Service-Type Calling-Station-Id Acct-Status-Type Acct-Delay-Time Acct-Session-Id Acct-Authentic Acct-Session-Time Acct-Terminate-Cause 16.10.2.3 Attributes Used for Accounting IEEE 802.1x Events The attributes are listed in the following table along with the time of the session they are sent: Table 281 RADIUS Attributes-Exec Events via 802.1x ATTRIBUTE START...
Page 531: Vlan Screens
H A P T E R VLAN Screens 17.1 VLAN Introduction A VLAN (Virtual Local Area Network) allows a physical network to be partitioned into multiple logical networks. Devices on a logical network belong to one group. A device can belong to more than one group.
Page 532: Forwarding Tagged And Untagged Frames
Chapter 17 VLAN Screens are independent of each other. A frame with VID (VLAN Identifier) of null (0) is called a priority frame, meaning that only the priority level is significant and the default VID of the ingress port is given as the VID of the frame. Of the 4096 possible VIDs, a VID of 0 is used to identify priority frames and value 4095 (FFF) is reserved, so the maximum possible VLAN configurations are 4,094.
Page 533: Gvrp
Chapter 17 VLAN Screens 17.3.2 GVRP GVRP (GARP VLAN Registration Protocol) is a registration protocol that defines a way for switches to register necessary VLAN members on ports across the network. Enable this function to permit VLANs groups beyond the local switch. Please refer to the following table for common IEEE 802.1Q VLAN terminology.
Page 534: Vlan Setup Screen
Chapter 17 VLAN Screens 3 The MSC ignores the port from which the frame came, because the MSC does not send a frame to the port from which it came. The MSC also does not forward frames to “forbidden” ports. 4 If after looking at the SVLAN, the MSC does not have any ports to which it will send the frame, it won’t check the port filter.
Page 535: Vlan Port Setting Screen
Chapter 17 VLAN Screens Table 283 VLAN Setup (continued) LABEL DESCRIPTION Registration Select Normal for the port to dynamically join this VLAN group using GVRP. Select Fix for the port to be a permanent member of this VLAN group. Select Forbidden if you want to prohibit the port from joining this VLAN group. You cannot change a port from the fixed state to another state if the port’s PVID is set to this VLAN.
Page 536: Vlan Port Setting Slot Screen
Chapter 17 VLAN Screens Figure 370 VLAN Port Setting The following table describes the labels in this screen. Table 284 VLAN Port Setting LABEL DESCRIPTION This is the slot number of a line card. Click the index number of an active line card to display which of the line card’s ports belong to which VLANs.
Page 537: Vlan Port Setting Slot Detail Screen
Chapter 17 VLAN Screens Figure 371 VLAN Port Setting Slot The following table describes the labels in this screen. Table 285 VLAN Port Setting Slot LABEL DESCRIPTION Port This is the label of a DSL port. Click a port’s index number to open a details screen about that port.
Page 538 Chapter 17 VLAN Screens MSC1000G/1024G/1224G Series User’s Guide...
Page 539: Voip
H A P T E R VoIP This chapter shows how to configure the Voice over IP (VoIP) features on your system. 18.1 VoIP Overview This section introduces VoIP, and discusses SIP and H.248 VoIP networks. 18.1.1 Introduction to VoIP VoIP (Voice over IP) is the sending of voice signals over the Internet Protocol.
Page 540 Chapter 18 VoIP 18.1.3.1 SIP Registration Each SIP-enabled VoIP line card in the IES is an individual SIP User Agent (UA). To provide voice service, it has an IP address for SIP and RTP protocols to communicate with other servers. A SIP user agent has to register with the SIP registrar and must provide information about the users it represents, as well as its current IP address (for the routing of incoming SIP requests).
Page 541 Chapter 18 VoIP 18.1.3.7 SIP User Agent A SIP user agent can make and receive VoIP telephone calls. A User Agent Client (UAC) is a logical entity that initiates a SIP request, and a User Agent Server (UAS) is a logical entity that creates a response to a SIP request.
Page 542 Chapter 18 VoIP The response to the request goes to all the proxy servers through which the request passed, in reverse sequence. Once the session is set up, session traffic is sent between the UAs directly, bypassing all the proxy servers in between. The following figure shows the SIP and session traffic flow between the user agents (UA 1 and UA 2) and the proxy servers (this example shows two proxy servers, PROXY 1 and PROXY 2).
Page 543: Introduction To H.248
Chapter 18 VoIP 3 Proxy 2 sends a SIP INVITE request to User Agent 2. 4 User Agent 2 sends a response back to Proxy 2 indicating that the phone is ringing. The response is relayed back to User Agent 1 via Proxy 1. 5 User Agent 2 sends an OK response to Proxy 2 after the call is answered.
Page 544 Chapter 18 VoIP Figure 375 SIP and H.248 Network Comparison IP NETWORK ANALOG ANALOG SIP ATA SIP ATA H.248 IP NETWORK ANALOG The IES uses H.248 interfaces that consist of a “Signaling Card” (SC) and at least one “Media Card” (MC). A VOP1248G-61 can act as either an SC, an MC, or both. The SC includes the Media Gateway (MG) and acts as an H.248 signaling gateway.
Page 545 Chapter 18 VoIP Figure 376 H.248 Media Gateway SC and MC MGC 1 MGC 2 IP NETWORK ANALOG H.248 signaling Other MG Line events Signal events ANALOG RTP payload An MC sends line events (like “onhook” and “offhook” to the SC. The SC sends signal events (like ring, metering pulse, and various tones) to the MCs.
Page 546 Chapter 18 VoIP Figure 377 H.248 Interface, SCs and MCs Interface Standby SC Backup Media Gateway Active SC Media Gateway IP NETWORK H.248 signaling RTP payload • The active SC uses the IP address of the H.248 interface to communicate with the MGC. •...
Page 547 Chapter 18 VoIP A Context is created when the MGC adds the first Termination to the Context. A Context is destroyed when the last Termination is removed from the Context. The following figure shows an example Context, C1. This Context possesses two Terminations, T1 and T2.
Page 548 Chapter 18 VoIP • Signals are instructions applied to Terminations by the MG when requested to do so by the MGC. The type and content of signals depends on the type of Termination (switched circuit network channel, RTP stream, etc.). Signals include media streams such as DTMF tones and audio messages.
Page 549 Chapter 18 VoIP Figure 380 H.248/MEGACO Call Procedure Example IP Network ANALOG ANALOG PHONE A PHONE B The user of phone A wants to call the user of phone B. The following table shows the series of actions necessary to set up the network and make the call (TransactionRequests and TransactionReplies are not shown).
Page 550 Chapter 18 VoIP Table 289 H.248/MEGACO Call Procedure Example DIRECTION ACTION COMMAND MGC --> MG1 MGC modifies Analog Termination on MG1 to send Modify ringing tone to phone A. MG1 --> Phone A MG1 send ringing tone to phone A. MG2 -->...
Page 551: Rtp
Chapter 18 VoIP 18.1.5 RTP When you make a VoIP call using SIP or H.248, the RTP (Real time Transport Protocol) is used to handle voice data transfer. See RFC 1889 for details on RTP. 18.1.6 Voice Coding A codec (coder/decoder) codes analog voice signals into digital signals and decodes the digital signals back into voice signals.
Page 552: Using Call Services
Chapter 18 VoIP Dual-Tone Multi-Frequency (DTMF) signaling uses pairs of frequencies (one lower frequency and one higher frequency) to set up calls. It is also known as Touch Tone®. Each of the keys on a DTMF telephone corresponds to a different pair of frequencies. Pulse dialing sends a series of clicks to the local phone office in order to dial numbers.
Page 553: Do Not Disturb
Chapter 18 VoIP 18.2.1 Do Not Disturb When Do Not Disturb (DND) is activated on a port, all incoming calls on that port are rejected. 18.2.1.1 Activating Do Not Disturb Take the following steps to activate DND on one of the VOP’s ports. Using a telephone connected to the port: 1 Dial “*99#”.
Page 554: Clir
Chapter 18 VoIP 18.2.3 CLIR When Calling Line Identification Restriction (CLIR) is active on one of the VOP’s ports, Caller ID is not sent for outgoing calls on the port. 18.2.3.1 Activating CLIR To activate CLIR on one of the VOP’s ports, dial “##” on a telephone connected to the port before you dial the phone number.
Page 555: The Voip Arp Screen
Chapter 18 VoIP 18.3 The VoIP ARP Screen Address Resolution Protocol (ARP) is a protocol for mapping an Internet Protocol address (IP address) to a physical machine address, also known as a Media Access Control or MAC address, on the local area network. Use the VoIP ARP screen to manage the IP addresses assigned to the VoIP cards in the IES.
Page 556 Chapter 18 VoIP Figure 382 The VoIP > Countrycode Screen The following table describes the labels in this screen. Table 292 The VoIP > Countrycode Screen LABEL DESCRIPTION Country Select the country in which the system will be used. Apply Click this to save your changes and display the region-specific VoIP settings below.
Page 557: The Countrycode Detail Screen
Chapter 18 VoIP Table 292 The VoIP > Countrycode Screen LABEL DESCRIPTION Off Time 1 (s) This displays the length of time between the first and second ring (in seconds). On Time 2 (s) This displays the duration of the second ring (in seconds). Off Time 2 (s) This displays the wait time after the second ring before the first ring is sent again (in seconds).
Page 558 Chapter 18 VoIP Figure 383 The VoiP > Countrycode > Detail Screen The following table describes the labels in this screen. Table 293 The VoIP > Countrycode > Detail Screen LABEL DESCRIPTION Click this to return to the VoIP > Countrycode screen. Pulse Parameters This section displays region-specific information about pulse dialling.
Page 559: The Voip Ip Screen
Chapter 18 VoIP 18.6 The VoIP IP Screen Use this screen to specify the IP address, subnet mask, VLAN ID and DNS information for each of the VoIP line cards managed by the IES. Click VoIP > IP. The following screen displays.
Page 560: The Voip Route Screen
Chapter 18 VoIP 18.7 The VoIP Route Screen Use this screen to set up and maintain routing for the VoIP line cards. The routing table contains entries that, based on the line card slot number and destination IP address or subnet, determine where the system forwards packets from the line cards.
Page 561: The Number Plan Screen
Chapter 18 VoIP Table 295 The VoIP > Route Screen LABEL DESCRIPTION Metric This displays an entry’s metric value. Select Select the entry you wish to modify or delete. Modify Select an entry profile and click this in order to edit its configuration. Delete Select a H.248 profile and click this to delete the profile.
Page 562 Chapter 18 VoIP The following table describes the labels in this screen. Table 296 The VoIP > Number Plan Screen LABEL DESCRIPTION Name Enter the name of the number plan table. If you are configuring a new number plan table, you can enter the name of the new table here. If you are looking an existing number plan table, this field is not editable.
Page 563: The Voip H248 Screen
Chapter 18 VoIP Table 296 The VoIP > Number Plan Screen LABEL DESCRIPTION Modify Select a number plan table and click this in order to edit its configuration. Delete Select a number plan table and click this to delete the profile. Once deleted, information cannot be retrieved.
Page 564: The Local Help Screen
Chapter 18 VoIP Table 297 The VoIP > H248 Screen LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 565 Chapter 18 VoIP Figure 388 The VoIP > Local Help Screen The following table describes the labels in this screen. Table 298 The VoIP > Local Help Screen LABEL DESCRIPTION Name Enter a name for this local help profile (up to 31 ASCII characters; spaces are not allowed).
Page 566: The Voip Key Pattern Screen
Chapter 18 VoIP Table 298 The VoIP > Local Help Screen LABEL DESCRIPTION Modify Select a local help table and click this in order to edit its configuration. Delete Select a local help table and click this to delete the profile. Once deleted, information cannot be retrieved.
Page 567 Chapter 18 VoIP The following table describes the labels in this screen. Table 299 The VoIP > Key Pattern Screen LABEL DESCRIPTION Name Enter a name for this key pattern profile (up to 31 ASCII characters; spaces are not allowed). Service Type These fields control the telephone keys a user presses to access a particular service.
Page 568: Dialplan Screen
Chapter 18 VoIP 18.12 Dialplan Screen The system uses dial plans to identify specific types of phone numbers dialed by a user, and to process the number before transmission by deleting or adding digits according to the relevant rule. The dial plan can also forward the call to a specific SIP server. Use a dial plan profile to collect a group of dial plans into a profile.
Page 569: The Localcall Screen
Chapter 18 VoIP Table 300 VoIP > Dialplan Screen LABEL DESCRIPTION Interdigit Timeout Enter the maximum number of seconds the system waits for each digit input of a complete callee number after you press the flash key on the phone. If the system does not receive the next digit entered within this time period, the system processes digits the caller has dialed.
Page 570: The Voip Interface Screen
Chapter 18 VoIP Table 301 VoIP > Localcall LABEL DESCRIPTION Apply Click Apply to save the changes in this screen to the system’s volatile memory. The system loses these changes if it is turned off or loses power, so use the Config Save on the navigation panel and then the Save button to save your changes to the non-volatile memory when you are done configuring.
Page 571 Chapter 18 VoIP Figure 392 VoIP > Interface The following table describes the labels in this screen. Table 302 VoIP > Interface LABEL DESCRIPTION Interface ID Select the number of the H.248 interface you want to configure and click Load. Interface IP/ Enter the H.248 interface’s IP address and subnet mask.
Page 572 Chapter 18 VoIP Table 302 VoIP > Interface LABEL DESCRIPTION Primary / Enter the slot numbers of the interface’s active and backup signaling cards. Secondary Slot MG Enable Select this to activate the media gateway. MG name Enter a name for the media gateway (up to 31 ASCII characters; spaces are not allowed).
Page 573: Config Save
H A P T E R Config Save Use this section to save changes to your system’s configuration. 19.1 The Config Save Screen Use this screen to save all configuration changes on to your MSC’s flash memory. If you do not use this screen, any changes you have made to the system’s configuration will be lost once the MSC is shut down.
Page 574 Chapter 19 Config Save MSC1000G/1024G/1224G Series User’s Guide...
Page 575: Commands
Commands Commands (577) acl Commands (583) alarm Commands (613) clear Commands (621) cluster Commands (623) config Commands (629) diagnostic Commands (631) ima Commands (645) ip Commands (657) lcman Commands (665) multicast Commands (669) port Commands (687) profile Commands (753) show Commands (819) switch Commands (867) sys Commands (905) vlan Commands (933)
Page 577: Commands
The default user name is “admin” and the default password is “1234”. This is the login message. User name: admin Password: **** Copyright (c) 1994 - 2009 ZyXEL Communications Corp. 20.2 Command Conventions The rules of the commands are listed next. 1 The command keywords are in font.
Page 578: Getting Help
Chapter 20 Commands 5 The | symbol means “or”. Using commands not documented in the user’s guide can damage the unit and possibly render it unusable. 20.3 Getting Help The system includes a help facility to provide you with the following information about the commands: •...
Page 579: Common Command Notation
Chapter 20 Commands 20.4 Common Command Notation The following table describes commonly used command parameter notation. Table 304 Common Command Notation NOTATION DESCRIPTION The optional fields in a command are enclosed in square brackets [], for instance, […] ip ping [<count>] means that the count field is optional.
Page 580: Command Privilege Levels
Chapter 20 Commands 20.5 Command Privilege Levels There is a high, middle, or low privilege level for each command. High privilege commands are only available to administrators with high privilege access. High privilege commands include things like creating administrator accounts, restarting the system and resetting the factory defaults.
Page 581: Commands Summary
Chapter 20 Commands Do not turn off your MSC while saving your configuration. This command saves all system configurations to nonvolatile memory. You must use this command to save any configuration changes that you make, otherwise the MSC returns to its last saved settings when it is restarted.
Page 582 Chapter 20 Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 583: Acl Commands
H A P T E R acl Commands This chapter describes the Access Control List management commands. 21.1 acl Commands Summary The following table lists the commands. The P column on the right indicates the administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 584 Chapter 21 acl Commands Table 306 acl Commands (continued) COMMAND DESCRIPTION Sets which DHCP relay mode the relaymode <vid> system uses for the specified [auto|both] VLAN. : send the requests to the auto active DHCP server first. If the active DHCP server does not respond, the switch sends the DHCP request to the backup DHCP server.
Page 585 Chapter 21 acl Commands Table 306 acl Commands (continued) COMMAND DESCRIPTION Activates DHCP snooping on the slot-port enable < > specified subscriber port(s). DHCP snooping allows the system to identify and block packets from devices using unknown/static IP addresses. Clears the DHCP snooping table flush <slot-port>...
Page 586 Chapter 21 acl Commands Table 306 acl Commands (continued) COMMAND DESCRIPTION Sets the authentication and secret <index> encryption key of the specified <secret_key> RADIUS server. index: The RADIUS server number. secret_key: The authentication encryption key (<=31 characters). Displays the external RADIUS show server settings.
Page 587 Chapter 21 acl Commands Table 306 acl Commands (continued) COMMAND DESCRIPTION Enables loop guard on the enable <giga- specified port(s). The system port>|<slot- shuts down a port if the system port> detects that packets sent out on the port loop back to the system. Note: The loop guard feature cannot be enabled on ports with...
Page 588 Chapter 21 acl Commands Table 306 acl Commands (continued) COMMAND DESCRIPTION Turns on the MAC filter on the enable <slot-port> specified subscriber ports. Sets the MAC filter actions. mode <slot-port> <accept|deny> Adds a MAC filter MAC address <slot-port> entry. <mac> Displays MAC filter settings.
Page 589 Chapter 21 acl Commands Table 306 acl Commands (continued) COMMAND DESCRIPTION Sets PPPoE line information. info <vid> description: Enter a <description> description (up to 24 characters). Selects the method (Private or optionmode <vid> TR-101) in which PPPoE line private|tr101 information is encoded in PPPoE [vid on|off] discover packets on the specified VLAN, and whether the VLAN ID...
Page 590: Acl Antimacspoof Commands
Chapter 21 acl Commands Table 306 acl Commands (continued) COMMAND DESCRIPTION Sets upstream broadcast storm usstorm <slot-port> control limits (from 0~148810) for <bcast> <mcast> the number of broadcast, <uucast> multicast, and/or unknown unicast packets the switch receives per second on the specified subscriber ports.
Page 591: Acl Dhcprelay82 Info Command
Chapter 21 acl Commands where ID of the VLAN to which this setting applies. <vid> Sets the relay mode. <mode> Activates DHCP relay service and include option 82 information in the client DHCP requests for this VLAN. Disables DHCP relay service but include option 82 information in the client DHCP requests.
Page 592: Acl Dhcprelay82 Relaymode Command
Chapter 21 acl Commands The following example sets the DHCP relay feature on VLAN 10 to use TR-101 encoding, and to transmit the VLAN ID. ras> acl dhcprelay82 optionmode 10 tr101 vid on 21.3.5 acl dhcprelay82 relaymode Command Syntax: acl dhcprelay82 relaymode <mode> where The system sends the requests to the active DHCP server first.
Page 593: Acl Dhcprelay82 Server Set Command
Chapter 21 acl Commands where A VLAN ID to be served with DHCP relay. <vid> The IP address of a DHCP server. <serverip> This command removes a DHCP server setting to which DHCP client requests are forwarded in the specific VLAN. 21.3.8 acl dhcprelay82 server set Command Syntax: acl dhcprelay82 server set <vid>...
Page 594: Dhcp Relay Option 82 (Agent Information) Sub-Option 2 (Remote Id)
Chapter 21 acl Commands The following figure shows an example. The asterisk (*) in front of a DHCP server address indicates that it is the active DHCP server in the VLAN. ras> acl dhcprelay82 show dhcp relay status: disable dhcp relay mode: both dhcp relay option82 info: [NULL]...
Page 595: Acl Dhcpsnoop Commands
Chapter 21 acl Commands where The ID of the VLAN to which to apply the setting. <vid> Up to 23 English keyboard characters of additional information for the <info> = MSC to add to the DHCP requests that it relays to a DHCP server. Examples of information you could add would be the name of the MSC or the ISP.
Page 596: Acl Dhcpsnoop Pool Set Command
Chapter 21 acl Commands 21.5.4 acl dhcpsnoop pool set Command Syntax: acl dhcpsnoop pool set <slot-port> <ip-address> This command adds a static IP address to the DHCP snooping table on a port. The following example adds two static IP addresses ( ) to 192.168.1.10 192.168.1.11...
Page 597: Acl Dot1X Disable Command
Chapter 21 acl Commands 21.6.1 acl dot1x disable Command Syntax: acl dot1x disable This command turns off the IEEE 802.1x authentication feature. 21.6.2 acl dot1x enable Command Syntax: acl dot1x enable This command turns on the IEEE 802.1x authentication feature. 21.6.3 acl dot1x port control Command Syntax: acl dot1x port control <slot-port>...
Page 598: Acl Dot1X Port Reauth Command
Chapter 21 acl Commands where Sets the IEEE 802.1x re-authentication period in seconds <secs> (60~65535). This command sets the IEEE 802.1x re-authentication period for the specified subscriber ports. 21.6.7 acl dot1x port reauth Command Syntax: acl dot1x port reauth <slot-port> on|off This command enables or disables the IEEE 802.1x re-authentication option for the specified subscriber ports.
Page 599: Acl Dot1X Radius Port Command
Chapter 21 acl Commands 21.6.10 acl dot1x radius port Command Syntax: acl dot1x radius port <index> <port> where The index number of an external RADIUS server entry (1 or 2). <index> The RADIUS server port number. <port> This command sets the external RADIUS server port number of the specified RADIUS server. 21.6.11 acl dot1x radius secret Command Syntax: acl dot1x radius secret <index>...
Page 600: Acl Dscp Set Command
Chapter 21 acl Commands This Device allows you to overwrite the DSCP priority using 802.1p priority for downstream traffic. Use acl dscp commands to configure the mapping between DSCP and 802.1p for DSL ports. Use switch port dscp commands to configure the mapping for Gigabit Ethernet interfaces (See Section 34.6.8 on page 883).
Page 601: Acl Maccount Disable Command
Chapter 21 acl Commands You cannot enable both MAC count and MAC filtering on the same port at the same time. 21.8.1 acl maccount disable Command Syntax: acl maccount disable <slot-port> This command disables the MAC count limit on the specified DSL port(s). The following example turns off the MAC count limit on DSL port 4 on a line card in slot 5.
Page 602: Acl Maccount Show Command
Chapter 21 acl Commands 21.8.4 acl maccount show Command Syntax: acl maccount show <slot> This command displays the MAC count settings for the DSL port(s). The following example displays the MAC count settings for slot 5. ras> acl maccount show 5 [slot5] maccount port enable count ----- ------ -----...
Page 603: Acl Macfilter Disable Command
Chapter 21 acl Commands The following example removes the source MAC address of a0:c5:12:34:56:78 from the MAC filter for ADSL port 5. ras> acl macfilter delete 5-4 a0:c5:12:34:56:78 21.9.2 acl macfilter disable Command Syntax: acl macfilter disable <slot-port> This command turns off the MAC filtering feature on a line card’s specified DSL port(s). The following example turns off the MAC filtering feature on DSL port 4 of the line card in slot 5.
Page 604: Acl Macfilter Show Command
Chapter 21 acl Commands This command adds an allowed source MAC address on a line card’s specified DSL port or on the DSL port in all of the line cards DSL ports if no slot is specified. The following example adds source MAC address a0:c5:12:34:56:78 for DSL port 4 of the line card in slot 5.
Page 605: Acl Ouifilter Enable Command
Chapter 21 acl Commands 21.10.2 acl ouifilter enable Command Syntax: acl ouifilter enable <slot-port> This command activates MAC OUI filtering on the port(s) of the specified line card. 21.10.3 acl ouifilter mode Command Syntax: acl ouifilter mode <slot-port> accept|deny where accept: Allows frames from MAC addresses with the OUI(s) that you accept|deny...
Page 606: Acl Pktfilter Commands
Chapter 21 acl Commands This command displays the OUI filtering status (V for enabled, - for disabled) and the OUI value(s) of the MAC address on a line card’s specified DSL port(s) or on all of the line card’s DSL ports if no port is specified. The following example displays the OUI filter setting of port 1 on the line card in slot 3.
Page 607: Acl Pktfilter Show Command
Chapter 21 acl Commands netbios: Reject NetBIOS packets. (Network Basic Input/Output System) are TCP or UDP broadcast packets that enable a computer to connect to and communicate with a LAN. Reject IGMP packets. Internet Group Multicast Protocol is used when igmp: sending packets to a specific group of hosts.
Page 608: Acl Pppoeagent Enable Command
Chapter 21 acl Commands 21.12.2 acl pppoeagent enable Command Syntax: acl pppoeagent enable <vid> This command turns on PPPoE line information for subscribers in the specified VLAN. The switch adds line information to PPPoE discover packets for user authentication and identification.
Page 609: Acl Pppoeagent Optionmode Command
Chapter 21 acl Commands The following example sets the switch to add “testing” as the line information to PPPoE discover packets on VLAN 10. ras> acl pppoeagent set 10 ras> acl pppoeagent enable 10 ras> acl pppoeagent info 10 testing ras>...
Page 610: Acl Rule Commands
Chapter 21 acl Commands This command displays PPPoE line information settings. The following figure shows the PPPoE agent setting for VLAN 10. ras> acl pppoeagent show info ---- ----- ------------------------ testing vlan set: 1 ras> 21.13 acl rule Commands Use the commands to apply ACL profiles (you created using the acl rule profile acl...
Page 611: Acl Rule Show Command
Chapter 21 acl Commands This command allows you to apply an access control profile to the specified DSL link(s). You can apply up to eight profiles to a subscriber port. The following example applies the “example” rule to PVC. ras> acl rule set 3-1-0/33 example 21.13.4 acl rule show Command Syntax: acl rule show <slot-port-vpi/vci>...
Page 612 Chapter 21 acl Commands The following figure shows an example. ras> acl usbcastctrl show usbcastctrl enable usbcastctrl rate = 96 MSC1000G/1024G/1224G Series User’s Guide...
Page 613: Alarm Commands
H A P T E R alarm Commands This chapter describes the alarm management commands. 22.1 General alarm Command Parameters The following table describes commonly used command parameter notation. alarm Table 307 General alarm Command Parameters NOTATION DESCRIPTION Specify a category of alarms. alarm represents equipment alarms.
Page 614 Chapter 22 alarm Commands Table 308 alarm Commands (continued) COMMAND DESCRIPTION Edits an alarm report entry. edit <alarm>|all <fac> <target>[,<targ et>] Sets the severity level of an alarm(s) xedit <alarm> <cond> and where the system is to send the <severity> alarm(s).
Page 615: Alarm Commands
Chapter 22 alarm Commands 22.3 alarm Commands Use these commands to view and clear alarms. You can also set the device to report alarms to an SNMP or syslog server that you specify. 22.3.1 alarm clear Command Syntax: alarm clear This command erases (clearable) historic alarm entries.
Page 616: Alarm History Show Command
Chapter 22 alarm Commands The following example removes the historic minor level alarms for all alarm categories, and all conditions. ras> alarm history clear minor 22.3.5 alarm history show Command Syntax: alarm history show [<severity>|all] [<alarm>|all] [<condition>|all] [<sdate>|all] [<edate>|all] [for|rev] [detail] This command displays historic alarms by severity, alarm category or alarm condition.
Page 617: Alarm Show Command
Chapter 22 alarm Commands where The log facility ( local1~local7 ) that has the device log the syslog <fac> messages to different files in the syslog server. See your syslog program’s documentation for details. snmp|syslog|all|none The type of alarm messages that the device <target>...
Page 618: Alarm Tablelist Command
Chapter 22 alarm Commands The following example displays the critical level alarms for all alarm categories and conditions. ras> alarm show critical all [current card alarm] state card type heat vol mon down out --- --------- --------------- --------------------- standby MSC1000G active MSC1000G ALC1248G-53...
Page 619: Alarm Xedit Command
Chapter 22 alarm Commands The following example displays the supported alarms for all alarm levels, all alarm categories, all facilities, all types of alarm messages and all conditions. ras> alarm tablelist no alarm (code)condition facility snmp syslog severity clearable --- ------ ------------------------- --------- ---- ------ -------- ------- ( 5002)LINE_UP local1...
Page 620 Chapter 22 alarm Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 621: Clear Commands
H A P T E R clear Commands This chapter describes the clear commands that you use to reset the various system counters. 23.1 clear Commands Summary The following table lists the clear commands you can use to reset the counters. Once you reset a counter, you can only display new counter information using the command.
Page 622: Clear Command Example
Chapter 23 clear Commands 23.2 clear Command Example The following example resets the IGMP counters on the system. This clears the IGMP counters and the number of IGMP groups learned. ras> clear igmp info MSC1000G/1024G/1224G Series User’s Guide...
Page 623: Cluster Commands
H A P T E R cluster Commands This chapter describes the cluster management commands. 24.1 General cluster Command Parameters The following table describes commonly used command parameter notation. cluster Table 310 General cluster Command Parameters NOTATION DESCRIPTION The device name (<=32 characters) name The device password (<=32 characters).
Page 624: Cluster Disable Command
Chapter 24 cluster Commands 24.2.1 cluster disable Command Syntax: cluster disable This command sets this DSLAM to not function as part of the cluster. 24.2.2 cluster enable manager Command Syntax: cluster enable manager <name> where A name to identify the cluster. You may use up to 32 printable characters. <name>...
Page 625: Cluster Member Candidate Show Command
The following is an example. After you log into a cluster member, the cluster name and the member’s ID number display in the command prompt. ras> cluster login 2 Copyright (c) 1994 - 2006 ZyXEL Communications Corp. 24.2.5 cluster member candidate show Command Syntax:...
Page 626: Cluster Member Show Command
Chapter 24 cluster Commands where An ID number (2~8) for the cluster member. <id> The hardware MAC address of the device <mac> The cluster member’s management password. If the administrator <password> changes the device’s management password afterwards, then it cannot be managed from the cluster manager.
Page 627: Cluster Vlan Command
Chapter 24 cluster Commands The following is an example. ras> cluster show mode :manager vlan :4094 name :Manager-A member list: id state hostname uptime model -- -------- --------------- ------------- ---------------- ----------------- 1 active 02:20:38 IES-5000 00:13:49:d1:d0:bc where Whether this device is the manager of the cluster or a member. mode This is the VLAN ID that the cluster uses and is only applicable if the vlan...
Page 628: Cluster Member Firmware And Configuration File Management
Chapter 24 cluster Commands This command sets the VLAN ID for the cluster. The following example sets the cluster VID to 79. ras> cluster vlan 79 24.3 Cluster Member Firmware and Configuration File Management You can use FTP to upload firmware to a cluster member through the cluster manager. You can also upload or download configuration files.
Page 629: Config Commands
H A P T E R config Commands This chapter describes the configuration file management commands. 25.1 config Commands Summary The following table lists the commands. The P column on the right indicates the config administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 630: Config Show Command
Chapter 25 config Commands This command saves your configuration when you are done with a configuration session. This command saves all system configuration to nonvolatile memory. You must use this command to save any configuration changes that you make, otherwise the system returns to its previously saved settings when it is restarted.
Page 631: Diagnostic Commands
H A P T E R diagnostic Commands This chapter describes the commands. diagnostic 26.1 Terms and Definitions This section lists the terms and definitions appearing in several commands in this section. Refer to your User’s Guide for more detailed information. Table 314 CFM Terms and Definitions TERM DESCRIPTION...
Page 632: General Diagnostic Command Parameters
Chapter 26 diagnostic Commands 26.2 General diagnostic Command Parameters The following table describes commonly used command parameter notation. diagnostic Table 315 General diagnostic Command Parameters NOTATION DESCRIPTION The maintenance domain name (length<32). md-name The maintenance association name (length<16). ma-name The endpoint identifier (1~8191). ep-id The remote end point identifier (1~8191).
Page 633: Diagnostic Commands Summary
Chapter 26 diagnostic Commands 26.3 Commands Summary diagnostic The following table lists the commands. The P column on the right indicates the diagnostic administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 634 Chapter 26 diagnostic Commands Table 316 diagnostic Commands (continued) COMMAND DESCRIPTION Sets the E1 physical loopback testing loopback set <slot-port> mode for the specified E1 port. <lpbkmode> lpbkmode: 0 (None LPBK): stop the previous E1 loopback test 1 (Line LPBK): return all physical or electrical signals received from the remote connected device 2 (In-ward LPBK): force all transmitted...
Page 635: Diagnostic Commands
Chapter 26 diagnostic Commands Table 316 diagnostic Commands (continued) COMMAND DESCRIPTION Displays the current MLT relay status of relay each VoIP line card’s ports. show Sends OAM loopback test Ethernet test <slot-port> <pkt- frames to a remote Ethernet device. number> <pktsize> Displays Ethernet OAM loopback test show <slot-port>...
Page 636: Diagnostic Cfm Linktrace Show Command
Chapter 26 diagnostic Commands Specify the MD name, MA name, MEP ID, destination (MEP ID or MAC address) to perform a loopback test. The following shows an example. ras> diagnostic cfm loopback testmd testma 1 2 loopback repId 2 received response ras>...
Page 637: Diagnostic Ldm Show Command
Chapter 26 diagnostic Commands Specify the MD name, MA name, MEP ID, destination (MEP ID or MAC address) to perform a link trace test. Syntax: diagnostic cfm linktrace set <md-name> <ma-name> <ep-id> <remote-ep-id>|<mac> <ttl> where The maintenance domain name (length<32). md-name The maintenance association name (length<16) ma-name...
Page 638: Diagnostic Ldm Test Command
Chapter 26 diagnostic Commands The following example performs loop diagnostics on DSL port 4 of the line card in slot 5. The command then displays the results of the ADSL port loop diagnostics. ras> diagnostic ldm show 5-4 result port 5-4: near end far end ------------...
Page 639: Diagnostic Loopback Internal Command
Chapter 26 diagnostic Commands 26.4.7 diagnostic loopback internal Command This command performs a loopback test on the specified DSL port. The following example performs loopback diagnostic on DSL port 5 of the line card in slot 2. The command then displays the results of the DSL port loop diagnostic. ras>...
Page 640: Diagnostic Mlt Show Command
Chapter 26 diagnostic Commands 26.5.2 diagnostic mlt show Command Syntax: diagnostic mlt show <slot-port> This command displays the results of the last Metallic Line Test that was run on the specified VoIP line card port. The following example shows the result of the last test conducted on the line connected to port 8 of slot 4.
Page 641: Diagnostic Oam Test Command
Chapter 26 diagnostic Commands 26.6.1 diagnostic oam test Command Syntax: diagnostic oam test <slot-port> <pkt-number> <pktsize> where Specify how many OAM loopback test Ethernet frames to send. pkt- number Specify the size of the OAM loopback test Ethernet frames (in bytes). pktsize This command sends OAM loopback test Ethernet frames to a remote Ethernet device.
Page 642: Diagnostic Selt Test Command
Chapter 26 diagnostic Commands 26.7.2 diagnostic selt test Command Syntax: diagnostic selt test <slot-port> This command starts the Single End Loop Test (SELT) on the specified port on the line card. This test checks the distance to the subscriber’s location. The port must have an open loop.
Page 643: Diagnostic Loopback Ima Commands
Chapter 26 diagnostic Commands The following example stops the E1 line loopback test on port 1 of slot 2 and then displays the loopback testing mode. ras> diagnostic loopback e1 set 2-1 0 ras> diagnostic loopback e1 show 2-1 slot-port E1 LPBK mode --------- -------------- 2- 1...
Page 644 Chapter 26 diagnostic Commands The following example stops the IMA loopback test on IMA group 1 on slot 2 and then displays the setting. ras> diagnostic loopback ima disable 2-1 ras> diagnostic loopback ima show 2-1 slot-group status test pattern ----------- ------- ------------ 2 - 1 disable...
Page 645: Ima Commands
H A P T E R ima Commands This chapter describes the commands. 27.1 General ima Command Parameters The following table describes commonly used command parameter notation. Table 317 General diagnostic Command Parameters NOTATION DESCRIPTION The number of a slot and a port on the slot. For example, 2-5 means port 5 on slot slot-port The number of a slot and an IMA group on the slot.
Page 646 Chapter 27 ima Commands Table 318 ima Commands (continued) COMMAND DESCRIPTION Displays all IMA DTPVC settings for the show <slot|gid|slot- specified IMA slot, IMA group, or IMA group-vpi/vci> group with a channel. Select the source of the clock which the group set <slot-gid>...
Page 647 Chapter 27 ima Commands Table 318 ima Commands (continued) COMMAND DESCRIPTION Enter the minimum number of E1 lines minlin <slot-gid> (1~8) the specified IMA group should <minlink> support. Once all of these E1 lines link up, the IMA group automatically activates.
Page 648 Chapter 27 ima Commands Table 318 ima Commands (continued) COMMAND DESCRIPTION Sets a routed management PVC. If the mgtpvc <slot-group-vpi/ remote IMA device uses a routed vci> <profile> encapsulated (RFC 1483) PVC for <llc|vcmux> management traffic transmission, you <management-ip> must configure the IES to use a routed <gateway-ip>...
Page 649: Ima Group Commands
Chapter 27 ima Commands Table 318 ima Commands (continued) COMMAND DESCRIPTION Displays all IMA PVC settings for the show <slot>|<gid>|<slot specified IMA slot, IMA group, or IMA -group-vpi/vci> group with a channel. Displays the MGT PVC to VLAN show mappings for each slot. 27.3 ima group Commands Syntax: ima group clk set <slot-gid>...
Page 650 Chapter 27 ima Commands where The number of one or multiple link(s) that you want to add into this IMA linklist group. For examples, 1,3 means links 1 and 3. 1~3 means links 1, 2 and This command sets link members for the specified IMA group. Syntax: ima group sym <slot-gid>...
Page 651 Chapter 27 ima Commands where This is the minimum number of E1 lines (1~8) the specified IMA group minlink should support. Once all of these E1 lines link up, the IMA group automatically activates. Disconnecting one of these E1 lines deactivates this IMA group.
Page 652: Ima Mgtpvc Commands
Chapter 27 ima Commands The following example shows the settings of IMA group 2 on slot 2. ras> ima group show 2-2 slot group state : enable frame size : 128 frame sync alpha frame sync beta frame sync gamma clock mode : ctc loop group symmetry...
Page 653 Chapter 27 ima Commands Figure 395 Routed MGTPVC Configuration Example IMA-1 IMA-2 192.168.1.3 192.168.1.2 192.168.1.1 The following shows how to map management frames with a PVC on IMA group 2 of slot 2 using the following settings: • Management frames: tagged with VLAN ID 100 and priority 7 •...
Page 654: Ima Pvc Commands
Chapter 27 ima Commands 27.5 ima pvc Commands Syntax: ima pvc set <slot-group-vpi/vci> <profile> <llc|vcmux> <pvid> <priority> This command sets a PVC on an IMA line card. The following example shows how to map specific single-tagged frames with a PVC on IMA group 1 of slot 2 using the following settings: •...
Page 655 Chapter 27 ima Commands This command sets a double-tagged PVC (DTPVC) on an IMA line card. The following example shows how to set a DTPVC on IMA group 3 of slot 2 using the following settings: • S-VID/S-PRI: VLAN ID 300 and priority 2 •...
Page 656 Chapter 27 ima Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 657: Ip Commands
H A P T E R ip Commands This chapter shows you how to use the commands to configure the IP (Internet Protocol) parameters. The ip commands are for management purposes, rather than for user traffic. 28.1 Commands Summary The following table lists the commands.
Page 658: Ip Commands
Chapter 28 ip Commands Table 319 ip Commands (continued) COMMAND DESCRIPTION Sets the management IP address, inband|outb subnet mask and in-band management and <ip- VLAN ID. address>[/ ip-address: ‘0.0.0.0’ disables a <netmask>] management interface. [<inband- inband-vid: The VLAN ID for this vid>] interface.
Page 659: Ip Arp Show Command
Chapter 28 ip Commands 28.2.2 ip arp show Command Syntax: ras> ip arp show This command displays the system’s IP Address Resolution Protocol (ARP) table. This is the list of IP addresses and matching MAC addresses that the device has resolved. An example is shown next.
Page 660: Ip Route Delete Command
Chapter 28 ip Commands 28.2.5 ip route delete Command Syntax: ras> ip route delete <dst-ip>[/<netmask>] <gateway> where The destination IP address of packets to which this static route applies. <dst ip> The destination subnet mask of packets to which this static route applies. [/netmask] The IP address of the gateway that you want to send the packets through.
Page 661: Ip Show Command
Chapter 28 ip Commands This command displays the system’s routing table. An example is shown next. ras> ip route show dest interface gateway metric name ------------------ ---------- --------------- ------ ---------------- 123.23.15.0/24 outband 123.23.15.86 123.23.19.233 outband 123.23.15.253 5 statroute1 192.168.1.0/24 inband 192.168.1.2 default outband...
Page 662 Chapter 28 ip Commands 28.2.9.1 Configuring Management VLAN Example After the following example configuration, you must connect through the third Ethernet port (uplink port 1) in order to perform inband management. You must connect through a VLAN aware device that is using the proper VLAN ID in order to perform management.
Page 663: Ip Tracert Command
Chapter 28 ip Commands 28.2.10 ip tracert Command Syntax: ras> ip tracert <ip-address> This command sends a traceroute packet to the IP address (in the field to the left) and uses the response to determine the path a packet takes to that IP address. The following example displays route information to an Ethernet device with an IP address of 123.23.19.11.
Page 664 Chapter 28 ip Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 665: Lcman Commands
H A P T E R lcman Commands This chapter shows you how to use the commands to manage the line cards. lcman 29.1 Commands Summary lcman The following table lists the commands. The P column on the right indicates the lcman administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 666: Lcman Reset Command
Chapter 29 lcman Commands This command turns off the management of the specified line card. This command is for troubleshooting. The system can automatically restart a line card that it is managing. If a line card is unresponsive and the command does not help, you may need to use lcman reset lcman...
Page 667 Chapter 29 lcman Commands The following table describes labels in the example. Table 321 lcman show Command LABEL DESCRIPTION This is the slot number. state This displays whether or not the installed card is turned on. This identifies the model of card that is installed or was last installed in the card type slot.
Page 668 Chapter 29 lcman Commands The following table describes labels in the example. Table 322 lcman show Command: Detailed Information LABEL DESCRIPTION This is the slot number followed by the model of card that is installed or was slot last installed in the slot. This is how long the card has been active.
Page 669: Multicast Commands
H A P T E R multicast Commands This chapter shows you how to use the commands. multicast 30.1 Commands Summary multicast The following table lists the commands. The P column on the right indicates the multicast administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 670 Chapter 30 multicast Commands Table 323 multicast Commands (continued) COMMAND DESCRIPTION Displays the settings of a static show <vid> <group- multicast MAC address. mac-addr> Turns off IGMP proxy or snooping. igmp disable Turns on IGMP proxy or snooping enable proxy|snooping using the specified version.
Page 671 Chapter 30 multicast Commands Table 323 multicast Commands (continued) COMMAND DESCRIPTION Turns on the IGMP count limit for a enable <slot-port> DSL port(s). Sets the IGMP count limit for a DSL <slot-port> port(s). <count> Displays the IGMP count limit setting show <slot>...
Page 672: Multicast Bandwidth Commands
Chapter 30 multicast Commands Table 323 multicast Commands (continued) COMMAND DESCRIPTION Configures a static multicast group <vid> <group- entry. ip> all|sub1|sub2|u p1|up2|<slot- port> fix|forbid|norm Displays the static multicast group show configuration. 30.2 multicast bandwidth Commands Use these commands to configure bandwidth requirements for multicast channels. 30.2.1 multicast bandwidth default Command Syntax: multicast bandwidth default <bandwidth>...
Page 673: Multicast Bandwidth Port Commands
Chapter 30 multicast Commands where A unique number for this setting. <index> The start of the multicast address range. <start- mcast-ip> The end of the multicast address range. For one multicast address, enter <end-mcast- the start multicast address again. ip> Allowed bandwidth between 1 and 1000 000 kbps (kilo bits per second).
Page 674: Multicast Bandwidth Port Show Command
Chapter 30 multicast Commands After using this command, if the device receives a join report and the total multicast traffic at that moment is over 1000 kbps, the device ignores the join report. 30.3.4 multicast bandwidth port show Command Syntax: multicast bandwidth port show <slot|slot-port>...
Page 675: Multicast Groupmacaddr Show Command
Chapter 30 multicast Commands This command configures static MAC multicast to allow incoming frames based on multicast MAC address(es) that you specify. Use this to pass allowed layer 2 multicast packets through the IES. The following example configures VID 2 to have the multicast MAC address 01:01:5E:00:00:05 on port 2 in slot 9 as a fixed member.
Page 676: Multicast Igmp Fastleave Disable Command
Chapter 30 multicast Commands 30.5.2 multicast igmp fastleave disable Command Syntax: multicast igmp fastleave disable This command deactivates multicast fastleave on the system. 30.5.3 multicast igmp fastleave timer Command Syntax: multicast igmp fastleave timer This command sets the time a device has to leave a multicast group. The following example specifies 10 seconds as the time the device has to leave a multicast group.
Page 677: Multicast Igmp Qryvid Delete Command
Chapter 30 multicast Commands 30.6.3 multicast igmp qryvid delete Command Syntax: multicast igmp qryvid delete <vid> This command removes an IGMP query VLAN ID. The following example removes IGMP query VLAN ID 6. ras> multicast igmp qryvid delete 6 30.6.4 multicast igmp qryvid set Command Syntax: ras>...
Page 678: Igmp Count Limit
Chapter 30 multicast Commands 30.7 IGMP Count Limit With the IGMP count feature, you can limit the number of IGMP groups a subscriber on a port can join. This allows you to control the distribution of multicast services (such as content information distribution) based on service plans and types of subscription.
Page 679: Multicast Igmpcount Show Command
Chapter 30 multicast Commands The following command sets a IGMP count limit of 2 for DSL port 4 on the line card in slot 3. ras> multicast igmpcount set 3-4 2 30.8.4 multicast igmpcount show Command Syntax: multicast igmpcount show <slot> This command displays the IGMP count limit setting status for the DSL ports on the line card in the specified slot.
Page 680: Multicast Igmpfilter Show Command
Chapter 30 multicast Commands The following example sets ADSL port 9 in slot 7 to use the IGMP filter profile. voice ras> multicast igmpfilter set 7-9 voice 30.9.2 multicast igmpfilter show Command Syntax: multicast igmpfilter show <slot> This command displays which IGMP filter profile DSL ports are using. The following example displays which IGMP filter profiles the DSL ports in slot 3 are using.
Page 681: Multicast Igmpmsgcount Set Command
Chapter 30 multicast Commands This command enables limiting the number of IGMP control messages allowed to flow through the specified slot and port. The following example enables limiting of the number of IGMP control messages on port number 2 on the line card in slot 5. ras>...
Page 682: Multicast Mvlan Delete Command
Chapter 30 multicast Commands 30.11.1 multicast mvlan delete Command Syntax: multicast mvlan delete <vid> This command removes the specified multicast VLAN configuration. 30.11.2 multicast mvlan disable Command Syntax: multicast mvlan disable <vid> This command deactivates the specified multicast VLAN. The following example disables multicast VLAN 12.
Page 683: Multicast Mvlan Group Delete Command
Chapter 30 multicast Commands 30.11.6 multicast mvlan group delete Command Syntax: multicast mvlan group delete <vid> <index> This command removes the specified multicast VLAN group configuration. 30.11.7 multicast mvlan name Command Syntax: multicast mvlan name <vid> <name> This command sets the name of the multicast VLAN. The following example sets the name of the multicast VLAN (VID =10) to “...
Page 684: Multicast Smcast Commands
Chapter 30 multicast Commands 30.12 multicast smcast Commands Use the following multicast commands to manage static multicast groups. 30.12.1 multicast smcast delete Command Syntax: multicast smcast delete <vid> <group-ip> where A multicast IP address. <group-ip> This command removes a static multicast group entry. The following example removes a static multicast group for VLAN 23 with static multicast address 239.255.255.255.
Page 685 Chapter 30 multicast Commands This command displays the system’s static multicast group configuration. An example is shown next. ras> multicast smcast show group slot port(F:fix, X:forbid, -:normal) ---- --------------- ---- ------------------------------------------------ 1 224.0.0.0 123456789012345678901234567890123456789012345678 1 XXXX 2 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 3 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 5 ------------------------------------------------ Press any key to continue, 'e' to exit...
Page 686 Chapter 30 multicast Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 687: Port Commands
H A P T E R port Commands This chapter shows you how to use the commands. port 31.1 General port Command Parameters The following table describes commonly used command parameter notation. port Table 324 General port Command Parameters NOTATION DESCRIPTION The name of an alarm profile configured using the profile alarm commands.
Page 688 Chapter 31 port Commands Table 325 port Commands COMMAND DESCRIPTION Applies an ADSL alarm profile to the port adsl alarmprof <slot-port> subscriber port. <alarmprofile> Turns off the Annex L reach extended annexl disable <slot- feature. port> Turns on the Annex L reach extended enable <slot-port>...
Page 689 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Sets the L0 (full power) and L2 (low power) param <slot-port> power mode transition settings. [l0time <l0time>] l0time : Time (10~ 65535 seconds) to [l2time <l2time>] stay in L0 mode. [l2pcb <l2atpr>...
Page 690 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Copies port settings from a source port to copy <source> destination ports on the same type of line <destination> card. Turns off a subscriber port. disable <slot-port> Removes the specified DTPVC. dtpvc delete <slot- port-vpi/vci>...
Page 691 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Sets the incoming or outgoing bandwidth enet bandwidth <slot-port> control for the specified Ethernet (ELC) <ingress-rate> subscriber port(s) (0~99968 Kbps). <egress-rate> ingress-rate: The incoming bandwidth rate on a port. egress-rate: The outgoing bandwidth rate on a port.
Page 692 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Removes G.bond settings from the DSL gbond delete <slot> <bond_name> lines specified in the G.bond group. bond_name: The name of a DSL line group with G.bond configured on them. Configures a G.bond group or modifies the set <slot>...
Page 693 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Displays domain settings. show[<domain name>] Sets a VLAN to join or leave a specified vlan <domain name> domain with maximum 8 VLANs in one <vid> domain. <registration> Deletes the specified edge router settings. edgerouter delete <ip- address>...
Page 694 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Sets the VLAN attributes of a PVC. vlan <slot-port-vpi/ vci> <vid> <registration> < > Sets a name for a subscriber port. name <slot-port> <name> Removes a PAE PVC (PPPoA-to-PPPoE paepvc delete <slot-port-vpi/...
Page 695 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Adds a priority-PVC into the group. set <slot-port- vpi/vci> <vpi/vci> atmprofile: Specify the ATM profile using profile atm commands. <atmprofile> <priority> Creates a priority-based PVC. <slot-port-vpi/ vci> <mux> <pvid> <priority>...
Page 696 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Sets SHDSL ports or end point(s) to use an shdsl alarmprof <slot-port> alarm profile. span|stuc|stur|* span : set alarm profile for the whole span <alarmprofile> stuc : set alarm profile at stuc end point : set alarm profile at stur end point stur : set alarm profile at both stuc and stur...
Page 697 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Displays the settings for a TLS PVC. show <slot>|<slot- port>|<slot-port- vpi/vci> Sets the VDSL port(s) to use the specified vdsl alarmprof <slot-port> alarm profile. <profile> Configures ADSL spectrum compatibility compatible <slot-port>...
Page 698 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Sets the VDSL port(s) VLAN priority (0~7). priority <slot-port> 0 is the lowest priority level and 7 is the <priority> highest. Sets the port VID on the VDSL port(s). pvid <slot-port>...
Page 699 Chapter 31 port Commands Table 325 port Commands (continued) COMMAND DESCRIPTION Creates an xVLAN entry for the specified set <slot-port> port. cvid is the original customer VLAN <cvid> <svid> ID. When the port receives traffic from the <cvid-s> subscriber with a cvid VLAN tag, xVLAN changes it to the svid before forwarding it to the service provider’s network.
Page 700: Port Commands
Chapter 31 port Commands 31.3 port Commands Use the commands to configure the line card ports. port 31.4 port adsl Commands Use the commands to configure the subscriber ADSL ports. port adsl 31.4.1 port adsl alarmprof Command Syntax: port adsl alarmprof <slot-port> <alarmprofile> where The name of an ADSL alarm profile.
Page 701: Port Adsl Annexm Disable Command
Chapter 31 port Commands The following example turns on the Annex L feature for port 7 on the line card in slot 5. ras> port adsl annexl enable 5-7 31.4.4 port adsl annexm disable Command Syntax: port adsl annexm disable <slot-port> This command turns off the Annex M double upstream feature on the specified ADSL2/2+ port(s).
Page 702: Port Adsl Dscarrier0 Command
Chapter 31 port Commands The following example turns on the Annex I feature for port 5 on the line card in slot 7. ras> port adsl annexi enable 7-5 31.4.8 port adsl dscarrier0 Command Syntax: port adsl dscarrier0 <slot-port> <m1> <m2> <m3> <m4> <m5> <m6> <m7> where The downstream carrier tones to be disabled.
Page 703: Port Adsl Inpmin Command
Chapter 31 port Commands where The downstream carrier tones to be disabled. Each <mx> can use up to 8 <m0> <m7> hexadecimal digits (0~ffffffff). Each <mx> represents 32 carrier tones (each hexadecimal digit represents 4 tones). tones 256~287 tones 288~319 tones 320~351 tones 352~383 tones 384~415...
Page 704: Port Adsl Optionmask Command
Chapter 31 port Commands The following example sets the impulse noise protection minimum to 2 DMT symbols for upstream and 4 DMT symbols for downstream for ADSL port 5 on the line card in slot 7. ras> port adsl inpmin 7-5 3 4 31.4.11 port adsl optionmask Command Syntax: port adsl optionmask <slot-port>...
Page 705: Port Adsl Pmm Enable Command
Chapter 31 port Commands The following example sets ADSL2+ port 5 on the line card in slot 7 to not use power management. ras> port adsl pmm disable 7-5 31.4.13 port adsl pmm enable Command Syntax: port adsl pmm enable <slot-port> [L2|L3] where Power management mode L2.
Page 706: Port Adsl Psd Maximum Command
Chapter 31 port Commands Maximum downstream transmit power, -50~200 in 0.1 dBm. <max_ds_txpwr> Maximum aggregate receive power at atu-c, -255~255 in 0.1 <max_rxpwr> dBm.This only applies to the ADSL2/2+ ADSL operational modes. This command specifies the maximum allowed transmit power and maximum aggregate received power.
Page 707: Port Adsl Uscarrier Command
Chapter 31 port Commands This command assigns a specific profile to an ADSL port(s) and sets the port’s ADSL mode (or standard). The profile defines the maximum and minimum upstream/downstream rates, the target upstream/downstream signal noise margins, and the maximum and minimum upstream/ downstream acceptable noise margins of all the ADSL ports to which you assign the profile.
Page 708: Port Copy Command
Chapter 31 port Commands 31.5 port copy Command Syntax: port copy <source> <destination> where The slot and port number from which you want to copy settings. <source> The slot and port number(s) to which you want to copy settings. <destination> This command copies the port settings from a source port to destination ports on the same type of line card.
Page 709: Dtpvc Mvlan Disable Command
Chapter 31 port Commands 31.7.2 dtpvc mvlan disable command Syntax: port dtpvc mvlan disable <slot-port-vpi/vci> This command turns off MVLAN for the specified DTPVC. The following example turns off MVLAN on DTPVC 8/35 on port 1 on the line card in slot 3. ras>...
Page 710: Dtpvc Show Command
Chapter 31 port Commands 31.7.5 dtpvc show command Syntax: port dtpvc show <slot>|<slot-port> This command displays the DTPVC configuration for the specified subscriber slot or port. The following example displays the DTPVC configuration for the line card in slot 5. ras>...
Page 711: Enet Commands
Chapter 31 port Commands 31.10 Enet Commands This section covers how to configure settings for the Ethernet subscriber ports (on the ELC). 31.10.1 port enet bandwidth Command Syntax: port enet bandwidth <slot-port> <ingress-rate> <egress-rate> where <ingress-rate> The maximum bandwidth allowed in kilobits per second (Kbps) for the incoming traffic flow on a port.
Page 712: Port Enet Dot3Ad Enable Command
Chapter 31 port Commands 31.10.4 port enet dot3ad enable Command Syntax: port enet dot3ad enable <slot> t1|t2|…|t10 [lacp] This command rns on link aggregation on the specified subscriber port trunk group. Use lacp to turn on LACP protocol. This example turns on link aggregation on the t1 trunk group on an ELC in slot 4. ras>...
Page 713: Port Enet Frametype Command
Chapter 31 port Commands The following example turns on the flow control on port 5 on the ELC in slot 4. ras> port enet flowctrl enable 4-5 31.10.8 port enet frametype Command Syntax: port enet frametype <slot-port> all|tag where Specifies all Ethernet frames (tagged and untagged) or only tagged Ethernet all|tag = frames.
Page 714: Port Enet Ratelimit Command
Chapter 31 port Commands The following example sets the PVID of port 5 on the ELC in slot 4 to 76. ras> port enet pvid 4-5 76 31.10.11 port enet ratelimit Command Syntax: port enet ratelimit <slot-port> <rate-limit_profile> This command sets the specified Ethernet port(s) to use a profile that limits egress and ingress rates.
Page 715: Port Enet Vlan Commands
Chapter 31 port Commands Use these commands to configure Transparent LAN Service (TLS) settings on the Ethernet subscriber port(s). Once you enable TLS, all packets will be added an extra “VLAN tag” (SPVID/SPriority) and forwarded toward Gigabit Ethernet interface(s). If you configure an ENET PVID setting and enable TLS, the system does not apply the PVID.
Page 716: Port Gbond Set Command
Chapter 31 port Commands 31.11.1 port gbond set Command Syntax: port gbond set <slot> <bond_name> <portlist> where The line card ID. <slot> A descriptive name for the gbond group of DSL lines. <bond_name> The ports on a line card that connect the DSL lines on which gbond is <portlist>...
Page 717: Port H248 Commands
Chapter 31 port Commands This command deletes the specified gbond group. The following is an example. ras> port gbond delete 2 group2 ras> port gbond show 2 slot bond name port list ---- ---------------------------------------- 2 Group1 31.12 Port h248 Commands Use these commands to configure the H.248 ports.
Page 718: Ip Bridge Commands
Chapter 31 port Commands 31.15 IP Bridge Commands These sections explain how to set up the IP bridge function in the system. The IP bridge function is designed for large-scale, flat, access networks, and it is ideal when the network is based on Ethernet. When the IP bridge is enabled, the system forwards frames based on the destination IP address, instead of the destination MAC address, and it replaces the source MAC address with its own MAC address.
Page 719: Port Ipbpvc Arpproxy Show Command
Chapter 31 port Commands IP address, in dotted decimal notation. <ip-address> Number of bits <1..32> in the subnet mask. <mask> The ID (<1..4094>) of the VLAN. <vid> This command clears the specified entries in the Address Resolution Protocol table(s). 31.16.3 port ipbpvc arpproxy show Command Syntax: port ipbpvc arpproxy show This command displays how long the device stores the IP addresses of IP bridge devices in the...
Page 720: Ip Bridge Domain Commands
Chapter 31 port Commands The following example deletes the IP bridge PVC on ADSL port 10 with VPI 40, VCI 73. ras> port ipbpvc show 1-10 type pvid pri ipbpvctype profile --------------- ------- ---- --- ---------- -------------------------------- 1-10-40/73 DEFVAL ras> port ipbpvc delete 1-10-40/73 ras>...
Page 721: Port Ipbpvc Domain Dhcpvlan Disable Command
Chapter 31 port Commands This command specifies the VLAN where the domain’s DHCP server is located. The VLAN must already be in the domain. The MSC forwards subscribers’ DHCP packets to the selected VLAN and changes the source MAC address to the MSC’s MAC address. The MSC still adds whatever Option 82 information is specified for the VLAN in the DHCP relay settings.
Page 722: Port Ipbpvc Domain Vlan Command
Chapter 31 port Commands This command displays the settings for the specified domain and the VLAN that are in the domain. An example is shown next. ras> port ipbpvc domain show domain ------------------------------- ---------------------------------------- ISP1 *101 102 example The output values correspond to the input values of other IP bridge domain commands. 31.19.6 port ipbpvc domain vlan Command Syntax: port ipbpvc domain vlan <domain name>...
Page 723: Port Ipbpvc Edgerouter Delete Command
Chapter 31 port Commands 31.20.1 port ipbpvc edgerouter delete Command Syntax: port ipbpvc edgerouter delete <ip-address> <vid> where IP address, in dotted decimal notation. <ip-address> = The ID (<1..4094>) of the VLAN. <vid> This command deletes the edge router with the specified IP address and VLAN ID. The following example deletes edge router 192.168.1.244 with VID 402.
Page 724: Ip Bridge Interface Commands
Chapter 31 port Commands An example is shown next. ras> port ipbpvc edgerouter show all domain ip/mask ------------------------------- ------------------ -------- ISP1 123.23.19.249/24 ISP1 123.23.19.254/24 example 192.168.1.200/24 The output values correspond to the input values of other IP bridge edge router commands. 31.21 IP Bridge Interface Commands Use these commands to set up and maintain forwarding information for downstream traffic.
Page 725: Port Ipbpvc Interface Set Command
Chapter 31 port Commands where Downlink interface’s IP address, in dotted decimal notation and number <ip/mask> of bits <1..32> in the subnet mask. The ID (<1..4094>) of the VLAN. <vid> The VPI and VCI of an individual PVC. vpi/vci This command creates the specified downlink interface. The /<mask>...
Page 726: Ip Bridge Routing Table Commands
Chapter 31 port Commands 31.22 IP Bridge Routing Table Commands Use these commands to set up and maintain the routing table for each domain. Each domain has its own routing table. Each routing table contains entries that, based on the destination IP address, control where the system forwards packets (for upstream and downstream traffic).
Page 727: Port Ipbpvc Route Show Command
Chapter 31 port Commands IP address, in dotted decimal notation. <nexthop> The metric <1..15> represents the “cost” of transmission for routing <metric> purposes. IP routing uses hop count as the measurement of cost, with a minimum of 1 for directly-connected networks. Select the number that approximates the cost for this link The number need not be precise, but it must be between 1 and 15.
Page 728: Port Ipbpvc Set Command
Chapter 31 port Commands An example is shown next. ras> port ipbpvc route show all domain ip/mask nexthop mtrc pr ------------------------------- ------------------ --------------- ---- -- ISP1 0.0.0.0/0 123.23.19.254 ISP1 192.169.1.0/24 123.23.19.249 example3 192.168.4.0/24 192.168.1.244 The output values correspond to the input values of other IP bridge routing table commands. 31.22.4 port ipbpvc set Command Syntax: port ipbpvc set <slot-port-vpi/vci>...
Page 729: Port Ipbpvc Vlan Command
Chapter 31 port Commands where The VPI and VCI of an individual PVC. vpi/vci This command allows you to display the PVCs for subscribers in an IP bridge. An example is shown next. ras> port ipbpvc show 1-10 type pvid pri ipbpvctype profile --------------- ------- ---- --- ---------- -------------------------------- 1-10-40/73 DEFVAL...
Page 730: Pppoa To Pppoe (Pae) Translation
Chapter 31 port Commands where A name to identify the subscriber port. <name> This command sets a name for the specified subscriber port(s). The following example sets port 5 on the line card in slot 2 to use the name Bob. ras>...
Page 731: Port Paepvc Set Command
Chapter 31 port Commands 31.24.2 port paepvc set Command Syntax: port paepvc set <slot-port-vpi/vci> <profile> <mux> <pvid> <priority> [acname <acname>] [srvcname <srvcname>] [hellotime <hellotime>] where Name of an ATM profile. <profile> <mux> Encapsulation method (llc or vcmux). <acname> This field is optional. Specify the hostname of a remote access concentrator if there are two access concentrators (or BRAS) on the network or that you want to allow PAE translation to the specified access concentrator.
Page 732: Port Ppvc Commands
Chapter 31 port Commands where <tx-gain> This sets the amount of gain (increase in volume) you want to apply to the signal received from the subscriber and transmitted to the SIP server. <rx-gain> This is the amount of gain (increase in volume) you want to apply to the signal received from the SIP server and transmitted to the subscriber.
Page 733: Port Ppvc Member Set Command
Chapter 31 port Commands The following example removes a PVC that uses VPI 8 and VCI 36 from a PPVC with VPI 8 and VCI 35 for port 5 on the line card in slot 7. ras> port ppvc member delete 7-5-8/35 8/36 31.26.3 port ppvc member set Command Syntax: port ppvc member set <slot-port-vpi/vci>...
Page 734: Port Ppvc Show Command
Chapter 31 port Commands The following example creates a PPVC with VPI 8 and VCI 35 for port 5 on the line card in slot 7. The PPVC uses llc encapsulation and default VID 25. Any frames received without an IEEE 802.1p priority tag will be assigned a priority of 3.
Page 735: Port Pvc Commands
Chapter 31 port Commands where The slot and port(s) and VPI/VCI of the PPVC. <slot-port-vpi/ vci> The VLAN ID. Valid parameter range = [1 – 4094]. <vid> This must be the VLAN ID of a VLAN that is already configured. The ports specified in this command must also be set to the fixed status in the VLAN.
Page 736: Port Pvc Mvlan Enable Command
Chapter 31 port Commands 31.27.3 port pvc mvlan enable Command Syntax: port pvc mvlan enable <slot-port-vpi/vci> This command enables multicast VLAN on the PVC. 31.27.4 port pvc set Command Syntax: port pvc set <slot-port-vpi/vci> <profile> <mux> <pvid> <priority> where The slot and port(s) and VPI/VCI of the PVC. <slot-port-vpi/ vci>...
Page 737: Port Pvc Usratelimit Enable Command
Chapter 31 port Commands The following example displays the virtual channels of DSL port 5 on the line card in slot 2. ras> port pvc show 2-5 type pvid mvlan profile --------------- ------- ----- ------ ---- ----- ------------ 2-5-0/33 bridged DEFVAL 2-5-8/35 bridged vcmux...
Page 738: Port Pvc Vlan Command
Chapter 31 port Commands This command displays upstream rate limiting settings on a PVC. The following example shows the PVC rate settings on port 1 of the line card in slot 5. ras> port pvc usratelimit show 5-1 rate -------------- ---- -------------- 5-1-0/33 1000(kbps) 31.27.10 port pvc vlan Command...
Page 739: Port Shdsl Pbo Command
Chapter 31 port Commands where span : Sets the alarm profile for the whole span. This is the entire span|stuc|stur|* connection including any SHDSL regenerators that might be located between the STU-C (SHDSL Termination Unit - Central) and STU-R (SHDSL Termination Unit - Remote) end points. An SHDSL regenerator amplifies the SHDSL signal in order to increase the connection distance.
Page 740: Port Shdsl Pmms Command
Chapter 31 port Commands This example sets SHDSL port 7 on the line card in slot 6 to use 13 dB of power backoff for both downstream and upstream. ras> port shdsl pbo 6-7 forced_no_epl 13 31.28.3 port shdsl pmms Command Syntax: port shdsl pmms <slot-port>...
Page 741: Port Show Command
Chapter 31 port Commands 31.29 port show Command Syntax: port show <slot>|<slot-port> This command displays the settings of the specified port(s). An example is shown next. ras> port show 7-5 port 7-5 name tel. no profile : DEFVAL alrm prof : DEFVAL state : enable...
Page 742: Port Sip Opmode Command
Chapter 31 port Commands 31.31 port sip opmode Command Syntax: port sip opmode <slot-port> <DEFVAL|v5sip> where Configures the port to use SIP to connect to a server. DEFVAL Configures the port to use V5.2 to connect to a traditional class 5 POTS v5sip switch.
Page 743: Port Tlspvc Delete Command
Chapter 31 port Commands 31.33.1 port tlspvc delete Command Syntax: port tlspvc delete <slot-port-vpi/vci> This command clears TLS settings for the PVC. 31.33.2 port tlspvc set Command Syntax: port tlspvc set <slot-port-vpi/vci> <profile> llc|vcmux <vid> <priority> where Name of an ATM profile. <profile>...
Page 744: Port Vdsl Commands
Chapter 31 port Commands 31.34.1 port vdsl alarmprof Command Syntax: port vdsl alarmprof <slot-port> <profile> This command sets the VDSL port(s) to use the specified alarm profile. 31.34.2 port vdsl compatible Command Syntax: port vdsl compatible <slot-port> none|adsl2|adsl2+ where Has the VDSL2 services use their normal frequency band plan. none Has the VDSL2 services not use the ADSL2 frequency bands to avoid adsl2...
Page 745: Port Vdsl Frequencyplan Command
Chapter 31 port Commands where Selects a band plan to use. For symmetric connections, use <997|998> asymmetric connections, enter A. Band plan 997 is not supported at the time of writing. This command sets the band plan the VDSL port(s) uses. The following example shows the configuration of port 5 on the VDSL card in slot 4 for an asymmetric connection.
Page 746: Port Vdsl Optionmask Command
Chapter 31 port Commands 31.34.7 port vdsl optionmask Command Syntax: port vdsl optionmask <slot-port> <option-mask> where The PSD mask value for the option bit. <option-mask> This command sets the PSD mask for the option bit on the specified port. The following example enables Trellis coding on traffic on port 5 on the VDSL card in slot 4. ras>...
Page 747: Port Vdsl Limitmask Show Command
Chapter 31 port Commands 31.34.9 port vdsl limitmask show Command Syntax: port vdsl limitmask show <limit_mask> where The PSD (Power Spectrum Density) mask. <limtmask> limitmask: 1: VDSL2_A_NUS0 2~11: VDSL2_A_EU[32,36,40,44,48,52,56,60,64,128] 12: VDSL1_FTTEX_ANSI_M1 13: VDSL1_FTTEX_ANSI_M2 14: VDSL1_FTTCAB_ANSI_M1 15: VDSL1_FTTCAB_ANSI_M2 16: VDSL1_FTTEX_ANSI_M1_e 17: VDSL1_FTTEX_ANSI_M2_e 18: VDSL1_FTTCAB_ANSI_M1_e 19: VDSL1_FTTCAB_ANSI_M2_e 20: VDSL2_A_CT...
Page 748: Port Vdsl Priority Command
Chapter 31 port Commands The following example shows the PSD mask for “VDSL2_A_NUS0”. ras> port vdsl limitmask show 1 1 (vdsl2_a_nus0) Upstream Band Plan Index ----------- -------- -------- -------- -------- Start tone 1981 5343 Stop tone 1196 2773 6947 Downstream Band Plan Index ----------- -------- -------- -------- -------- Start tone...
Page 749: Port Vdsl Rfiband Command
Chapter 31 port Commands where The ether type in hexadecimal. <etype> The VLAN ID from 1~4094 <vid> The priority setting from 0~7 <priority> This command sets a private VLAN setting on a specified DSL port. The following example sets up a private VLAN with an IPv6 Ethernet type, an ID of 1 and a priority of 1 on traffic on port 5 on the VDSL card in slot 4.
Page 750: Port Vdsl Set Command
Chapter 31 port Commands • Show the settings. ras> port vdsl rficustom set 1 3500 3800 ras> port vdsl rficustom enable 1 ras> port vdsl rficustom show index state start_freq stop_freq ------- ------- ------------ ----------- 3500 3800 ras> 31.34.15 port vdsl set Command Syntax: port vdsl set <slot-port>...
Page 751: Port Vdsl Upbo Commands
Chapter 31 port Commands • Configures the service provider’s VID to 10 and VLAN priority to 7 (highest priority). ras> port vdsl tls enable 4-5 ras> port vdsl tls set 4-5 10 7 31.34.17 port vdsl upbo Commands Syntax: port vdsl upbo <slot-port> <on|off> This command enables or disables Upstream Power Back Off (UPBO) on the VDSL port(s).
Page 752 Chapter 31 port Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 753: Profile Commands
H A P T E R profile Commands This chapter shows you how to use the commands. profile 32.1 Profiles Overview Profiles are groups of settings that you can assign to a port(s). This helps simplify and speed up port configuration. 32.2 General profile Command Parameters The following table describes commonly used command parameter notation.
Page 754: Profile Commands Summary
Chapter 32 profile Commands 32.3 Commands Summary profile The following table lists the commands. The P column on the right indicates the profile administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 755 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Creates a profile of ADSL alarm <profile> atuc settings. [lofs <lofs>] [loss <loss>] [lols <lols>] [lprs <lprs>] [ess <ess>] [ffr <ffr>] [sesl <sesl>] [uasl <uasl>] [fru <fru>] [iru <iru>] [frd <frd>] [ird <ird>] [ift <ift>]...
Page 756 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Displays which ADSL ports reference <profile> this alarm profile. Creates a profile of ADSL alarm <profile> atuc settings. See Section 32.6.2 on page [lofs <lofs>] for more information. [loss <loss>] [lols <lols>] [lprs <lprs>] [ess <ess>] [ffr...
Page 757 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Creates a profile of VDSL alarm <profile> settings. [lofs <lofs>] cv: The maximum number of code [loss <loss>] violations (CRC errors). [lols <lols>] [lprs <lprs>] [ess <ess>] [ffr <ffr>] [sesl <sesl>] [uasl <uasl>] [fru <fru>]...
Page 758 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Creates an alarm VDSL2 line profile of set <profile> 15 minute period alarm thresholds. A 0 [xtucfecs has the system ignore that threshold. <0~900>] [xtuces xtucfecs: the number of Forward <0~900>] [xtucses Error Correction Seconds (FECS) <0~900>][xtuclos...
Page 759 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Displays which ports reference this <profile> ATM profile. Creates a profile of ATM traffic <atmprofile> settings. cbr|ubr <pcr> : constant cell rate <cdvt> ubr: unspecified cell rate : real time variable bit rate rt-vbr nrt-vbr : non-real time variable bit...
Page 760 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Sets the PIR, CIR, PBS, CBS queue <profile> <queue- parameters for an IPQoS profile. id> <pir> <cir> queue-id: The queue index <pbs> <cbs> beginning at 0. For example, if you [<level>...
Page 761 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Removes an unreferenced SHDSL shdsl delete <profile> port settings profile. Displays which SHDSL ports reference <profile> this profile. Creates a profile of SHDSL port <profile> <min- settings. rate> <max-rate> min-rate: The minimum rate [<annex>...
Page 762 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Creates a VDSL line profile. See <profile> <us- Section 32.16.3 on page 795 for more max-rate> <ds- information. max-rate> [fast|delay <us- delay> <ds- delay>] [minrate <us-min-rate> <ds-min-rate>] [usmgn <us-max- mgn>...
Page 763 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Creates a VDSL2 channel profile. set <profile> [minrateds <ds_min_rate>] [minrateus <us_min_rate>] [maxrateds <ds_max_rate>] [maxrateus <us_max_rate>] [maxdelayds <delay>] [maxdelayus <delay>] [mininpds <min_inp>] [mininpus <min_inp>] [mininp8ds <min_inp8>] [mininp8us <min_inp8>] [phyrds <enable|disable| auto>] [phyrus <enable|disable| auto>]...
Page 764 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION This command creates and configures <name> a DSP (Digital Signal Processing) [codec <codec> profile. [,<codec>...] codec: Available codecs are: [playbuffer G.711a: g711a <min-delay> <max- G.711µ: g711mu delay>] G.723: g723 [echotail G.726 <echotail>]...
Page 765 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Configures an H.248 profile. <profile> <mgc- ip>|<mgc-dn> Section 32.19.3 on page 807 more information on this command. [mgcport <mgc- port>][mgc2 The default H248 profile values are: off|{on <mgc2- name: DEFVAL ip>|<mgc2-dn>}] mg-name: DEFVAL [mgc2port <mgc2-...
Page 766 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Configures the specified SIP profile. <name> <sip- The system supports up to 128 SIP ip>|<sip-dn> profiles. <regsvr- sip-ip: The SIP server’s IP address. ip>|<regsvr-dn> sip-dn: The SIP server’s domain <proxysvr- name (maximum 256 characters).
Page 767 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Configures a new call service profile. callsvc set <name> [keypattern keypattern: Enter the VoIP key pattern to use. <pattern-table>] [nopassword | Once the password configuration is set, it cannot be changed. {password <password>} The system supports up to 128 call...
Page 768 Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION Continued: callhold: Allows (on) or prohibits (off) call holding. callwait: Allows (on) or prohibits (off) call waiting. callreturn: Call return allowed/ prohibited. cidcw: Calling Identity Delivery on Call Waiting allowed/prohibited. clip: Allows (on) or prohibits (off) caller ID presentation.
Page 769: Profile Acl Commands
Chapter 32 profile Commands Table 327 profile Commands (continued) COMMAND DESCRIPTION mwi: Turns the message waiting indicator on or off. reanswer: When the system is using v5sip mode, use this field to set the reanswer time period. The reanswer time controls the length of time between the user hanging up the phone, and the call being disconnected (the BYE request being sent).
Page 770 Chapter 32 profile Commands where: The rule that classifies traffic flows. Ordering of the criteria is important. The <rule> system first compares the layer 2 fields first, the layer 3 fields and then the protocol type. The following lists the set of criteria you can configure. Note that the device takes the order when matching rules.
Page 771: Profile Acl Show Command
Chapter 32 profile Commands This command configures an ACL rule to classify the upstream traffic and perform action(s) on the classified traffic. The following creates an ACL rule example named for traffic from VLAN 10 with a test priority level of 2. This rule limits the rate on the classified traffic to 1024 kbps and changes the priority level to 7.
Page 772 Chapter 32 profile Commands where The descriptive name for the profile. <profile> The maximum ADSL upstream transmission rate, 64~4096 in Kbps. <us-max-rate> The upstream rate must be less than or equal to the downstream rate. The maximum ADSL downstream transmission rate, 64~32000 in <ds-max-rate>...
Page 773: Profile Adsl Map Command
Chapter 32 profile Commands • The minimum upstream is set to 1024 Kbps. • The minimum downstream is set to 3072 Kbps. • The maximum, minimum and target acceptable ADSL upstream signal to noise margins are set to 12, 0 and 6 dB respectively. •...
Page 774: Profile Adsl Show Command
Chapter 32 profile Commands The following example deletes the gold ADSL profile. ras> adsl profile delete gold 32.5.4 profile adsl show Command Syntax: profile adsl show [<profile>] where A profile name. <profile> This command displays the details of the specified ADSL profile or lists all of the ADSL profiles if you do not specify one.
Page 775: Profile Alarmadsl Set Command
Chapter 32 profile Commands The following example displays the default alarm ADSL profile (DEFVAL). ras> profile alarmadsl show DEFVAL adsl alarm profile : DEFVAL atuc atur ---------- ---------- 15MinLofs(lofs) (sec): 15MinLoss(loss) (sec): 15MinLols(lols) (sec): 15MinLprs(lprs) (sec): 15MinESs(ess) (sec): 15MinFailedFastR(ffr) (sec): 15MinSesL(sesl) (sec): 15MinUasL(uasl)
Page 776: Profile Alarmadsl Delete Command
Chapter 32 profile Commands The number of UnAvailable Seconds (0~900) that are permitted to occur <uasl> within 15 minutes. A rate in kilobits per second (Kbps). If a fast mode connection’s upstream <fru> transmission rate increases by more than this number, then a trap is sent. A rate in kilobits per second (Kbps).
Page 777: Profile Alarme1 Commands
Chapter 32 profile Commands where The name of an alarm profile. <profile> This command displays which ADSL ports are set to use the specified alarmadsl profile. The following example displays which ADSL ports use the SESalarm alarmadsl profile. ras> profile alarmadsl map SESalarm 32.7 profile alarme1 Commands Configure E1 profiles to set alarm settings and thresholds for the E1 ports.
Page 778: Profile Alarme1 Delete Command
Chapter 32 profile Commands The number of Severely Errored Seconds (0~900) that are permitted to qses occur within 15 minutes. The number of UnAvailable Seconds (0~900) that are permitted to occur quas within 15 minutes. The number of Error Seconds (0~86400) that are permitted to occur within dayes one day.
Page 779: Profile Alarmshdsl Commands
Chapter 32 profile Commands The following example displays which E1 ports use the SESalarm E1 alarm profile. ras> profile alarme1 map SESalarm side port -- ---- ------------------------------------------------------------------- ----- 123456789012345678901234567890123456789012345678901234567890123456789012 - -------------------- - -------- - -------------------------------------------------------------------- ---- - ------------------------ - ------------------------------------------------ - ------------------------ - ------------------------------------------------ - ------------------------------------------------...
Page 780: Profile Alarmshdsl Set Command
Chapter 32 profile Commands The following example displays the default alarm SHDSL profile (DEFVAL). ras> profile alarmshdsl show DEFVAL shdsl alarm profile : DEFVAL loop attenuation(atten) (dB): snr margin(snrmgn) (dB): (sec): (sec): crc anomalies(crc) losws (sec): (sec): ras> 32.8.2 profile alarmshdsl set Command Syntax: <profile>...
Page 781: Profile Alarmshdsl Delete Command
Chapter 32 profile Commands 32.8.3 profile alarmshdsl delete Command Syntax: profile alarmshdsl delete <profile> where The name of an alarm profile. <profile> This command allows you to delete an individual SHDSL alarm profile by its name. You cannot delete the DEFVAL alarm profile. The following example deletes the SESalarm alarm profile.
Page 782: Profile Alarmvdsl Set Command
Chapter 32 profile Commands The following example displays the default alarm VDSL profile (DEFVAL). ras> profile alarmvdsl show DEFVAL vdsl alarm profile : DEFVAL initFailure(ift) 15MinLofs(lofs) (sec): 15MinLoss(loss) (sec): 15MinLols(lols) (sec): 15MinLprs(lprs) (sec): 15MinESs(ess) (sec): 15MinSesL(sesl) (sec): 15MinUasL(uasl) (sec): ras> 32.9.2 profile alarmvdsl set Command Syntax: profile alarmvdsl set <profile>...
Page 783: Profile Alarmvdsl Delete Command
Chapter 32 profile Commands The following example sets an alarm profile named SESalarm that has the system send an alarm trap and generate a syslog whenever the connection (from the IES to the subscriber) has more than 3 severely errored seconds within a 15-minute period. ras>...
Page 784: Profile Atm Show Command
Chapter 32 profile Commands 32.10.1 profile atm show Command Syntax: profile atm show [<profile>] where A profile name. profile This command displays the details of the specified ATM profile or lists all of the ATM profiles if you do not specify one. The following example displays the DEFVAL ATM profile.
Page 785: Profile Atm Delete Command
Chapter 32 profile Commands The following example creates an ATM profile named gold. It uses constant bit rate and has the maximum rate (peak cell rate) set to 300,000 cells per second. The acceptable tolerance of the difference between a cell’s transfer delay and the expected transfer delay (CDVT) is set to 5 cells.
Page 786: Profile Server
Chapter 32 profile Commands where The name of a profile. <profile> This command displays which PVCs or PPVCs are set to use the specified ATM profile. The following example displays which PVCs or PPVCs use the silver profile. ras> profile atm map silver 32.11 Profile Server The profile server feature manages profiles on multiple IES’s.
Page 787: Profile Ipqos Queue Command
Chapter 32 profile Commands This command displays the EXAMPLE IPQoS profile settings. ras> profile ipqos show EXAMPLE ipqos profile : EXAMPLE queue number level weight --- ------ ------ ------ ------ ------ ------ 0 131072 65536 65536 65536 1088 1024 3072 3072 2 131072 65536...
Page 788: Profile Ipqos Map Command
Chapter 32 profile Commands Set the queue’s priority level 0~7. The larger the number, the higher level the priority. You can configure different IPQoS profiles with queues that have weight the same queue priority level. IPQoS then uses Weighted Round Robin (WRR) scheduling to service these queues on a rotating basis based on their queue weight.
Page 789: Profile Profsvr Commands
Chapter 32 profile Commands This command removes the specified IPQoS profile. Here is how to delete the EXAMPLE IPQoS profile. ras> profile ipqos delete EXAMPLE 32.13 profile profsvr Commands Use these commands to configure the profile server feature settings. 32.13.1 profile profsvr show Command Syntax: profile profsvr show This command displays the current profile server setting.
Page 790: Profile Profsvr Clientlist Delete Command
Chapter 32 profile Commands The following example sets a profile server client entry for an IES at IP address 1.2.3.4. If there are any unused profiles on this client during the synchronization process, they will be left on the client. ras>...
Page 791: Profile Ratelimit Commands
Chapter 32 profile Commands 32.14 profile ratelimit Commands Use these commands to configure Ethernet subscriber line ingress and egress rate profiles 32.14.1 profile ratelimit delete Command Syntax: profile ratelimit delete <profile> This command removes the specified Ethernet subscriber port rate limit profile. You cannot remove a rate limit profile that is currently in use.
Page 792: Profile Ratelimit Show Command
Chapter 32 profile Commands This command configures an Ethernet subscriber line ingress and egress rate profile. The following creates an Ethernet subscriber line profile named test that limits ingress and egress traffic to 12,800 Kbps. ras> profile ratelimit set test 12800 12800 32.14.4 profile ratelimit show Command Syntax: profile ratelimit show [<profile>]...
Page 793: Profile Shdsl Map Command
Chapter 32 profile Commands The wire pair number. 2wire|4wire|mpair4 2wire : A normal connection using a single SHDSL port’s two wires, this is the default. 4wire : A 4-wire n-wire group (two SHDSL ports grouped together). mpair4 : An 8-wire n-wire group (four SHDSL ports grouped together).
Page 794: Profile Shdsl Delete Command
Chapter 32 profile Commands where The name of the profile. <profile> This command displays which SHDSL ports reference a specific profile. The following example displays which SHDSL ports use the gold profile. ras> profile shdsl map gold 32.15.3 profile shdsl delete Command Syntax: profile shdsl delete <profile>...
Page 795: Profile Vdsl Commands
Chapter 32 profile Commands 32.16 profile vdsl commands Use the commands to configure VDSL profiles. profile vdsl 32.16.1 profile vdsl delete command Syntax: profile vdsl delete <profile> where A profile name. <profile> This command allows you to delete an individual shdsl profile by its name. You cannot delete a profile that is assigned to any of the DSL ports in the system.
Page 796: Profile Vdsl Show Command
Chapter 32 profile Commands The latency mode. With interleave, you must also define the [fast|delay <us- upstream and downstream delay (1-255 ms). It is recommended delay> <ds-delay>] that you configure the same delay for both upstream and downstream. The minimum VDSL upstream transmission rate (32~45440 Kbps) [minrate <us-min- and the minimum ADSL downstream transmission rate (32~100032 rate>...
Page 797: Profile Vdsl2 Commands
Chapter 32 profile Commands where The descriptive name for the profile. <profile> This command displays the VDSL profile list of the settings of a VDSL profile configured on the system. The following example displays the profile list and the settings of the profile.
Page 798: Profile Vdsl2 Lineprofile Set Command
Chapter 32 profile Commands 32.17.1 profile vdsl2 lineprofile set Command Syntax: profile vdsl2 lineprofile set <profile> [ramodeds manual|rainit|dynamicra] [ramodeus manual|rainit|dynamicra] [rausnrmds <up_shift_nrm_ds>] [rausnrmus <up_shift_nrm_us>] [raustimeds <up_shift_time>] [raustimeus <up_shift_time>] [radsnrmds <down_shift_nrm_ds>] [radsnrmus <down_shift_nrm_us>] [radstimeds <down_shift_time>] [radstimeus <down_shift_time>] [targetsnrmds <target_margin_ds>] [targetsnrmus <target_margin_us>] [maxsnrmds <max_margin_ds>] [maxsnrmus <max_margin_us>] [minsnrmds <min_margin_ds>]...
Page 799 Chapter 32 profile Commands where = The descriptive name for the profile. Up to 31 <profile> characters. = The downstream (ds) and upstream (us) rate [ramodeds adaption settings. <manual|rainit|dynamicra>] manual fixes the transmit rate as the minimum net data rate and disable transmission rate adjustment. If the attainable speeds cannot match configured [ramodeus speeds, then the VDSL link may go down or link...
Page 800 Chapter 32 profile Commands = The downstream (ds) and upstream (us) maximum [maxsnrmds <max_margin_ds>] SNR (Signal to Noise Ratio) margin allowed on the line. When the actual SNR margin is going to reach [maxsnrmus <max_margin_us>] this specified value, this mechanism forces connected CPE device(s) to lower its transmission power level and maintains the actual SNR margin equal to or less than this value.
Page 801 Chapter 32 profile Commands = Enables or disables the downstream (ds) or [snrmodeds disable|enable] upstream (us) transmitter reference virtual noise. [snrmodeus disable|enable] = Adds virtual noise levels on downstream (ds) or [refvnds <tone_index> <vn_psd> upstream (us) tones where actual noise may [...] occur.
Page 802 Chapter 32 profile Commands = DPBOEPSD (Assumed Exchange PSD Mask) [dpboepsd <tone> <epsd> defines the PSD mask that is assumed to be [...]|<psdid>] exchanged at CO. Use this graph to view PSD level to frequency relationship. The horizontal is frequency in MHz and vertical is power level in dBm/Hz.
Page 803: Profile Voip Dsp Commands
Chapter 32 profile Commands = Adjusts the MIB PSD level on downstream tones. [psdmaskds <tone-index1> <psd- level> [<tone-index2> <psd- tone-index: Enter a number from 0 to 4096. A tone is a sub-channel of VDSL band. DMT divides level>] ... VDSL bands into many 4.3125 kHz tones. psd-level: Enter from 0 (0 dBm/Hz) to 255 (- 127.5 dBm/Hz) in steps of 0.5dBm/Hz.
Page 804: Profile Voip Dsp Set Command
Chapter 32 profile Commands This command displays which subscribers use the specified DSP profile. An example is shown, displaying the subscribers that use a DSP profile named “digsig3”. ras> profile voip dsp map digsig3 slot port ---- ------------------------------------------------ 123456789012345678901234567890123456789012345678 4 V-V-V-V-V-V-V-V-V-V-V-V-V-V-V-V-V-V-V----------- 8 ------------------------ 32.18.3 profile voip dsp set Command Syntax:...
Page 805: Profile Voip Dsp Show Command
Chapter 32 profile Commands Set the G.723 voice package interval, 30 or 60 ms. g723-vpi Set the G.726 voice package interval, 10, 20, 30 or 40 ms. g726-vpi Set the G.729 voice package interval, 10, 20, 30, 40, 50 or 60 ms. g729-vpi This command creates and configures a DSP (Digital Signal Processing) profile.
Page 806: Profile Voip H248 Commands
Chapter 32 profile Commands This command displays the settings of the specified DSP profile, or displays the names of all DSP profiles if none is specified. An example is shown next. ras> profile voip dsp show dsp profile(s) ------------------------- 1. DEFVAL 2.
Page 807: Profile Voip H248 Set Command
Chapter 32 profile Commands 32.19.3 profile voip h248 set Command Syntax: profile voip set h248 <profile> <mgc-ip>|<mgc-dn>[mgcport <mgc-port>][mgc2 off|{on <mgc2-ip>|<mgc2-dn>}][mgc2port <mgc2-port>][transport udp|tcp][encode long|short][pbit <pbit>][dscp <dscp>] where The primary and secondary MGC server IP address. <mgc-ip> <mgc2-ip> The primary and secondary MGC server domain name (maximum 256 <mgc-dn>...
Page 808: Profile Voip Sip Delete Command
Chapter 32 profile Commands 32.20.1 profile voip sip delete Command Syntax: profile voip sip delete <name> This command removes the specified SIP profile. An example is shown to delete the SIP profile named “bar”. ras> profile voip sip delete bar 32.20.2 profile voip sip map Command Syntax: profile voip sip map <name>...
Page 809 Chapter 32 profile Commands The registrar server port number (1025 ~ 65535). <regsvr-port> The SIP proxy server port number (1025 ~ 65535). <proxysvr- port> The profile uses SIP URI. uritype SIP The profile uses TEL URI. uritype TEL The IEEE 802.1p priority tag for SIP and RTP packets (0 ~ 7). <pbit>...
Page 810: Profile Voip Sip Show Command
Chapter 32 profile Commands • PRACK: on ras> profile voip sip set sip10 host1.domain1 host2.domain2 host3.domain3 sipport 5061 regsvrport 5062 proxysvrport 5063 uritype sip pbit 5 dscp 36 keepalive on 1000 prack on 32.20.4 profile voip sip show Command Syntax: profile voip sip show [<name>] This command displays the settings of the specified SIP profile, or displays the names of all SIP profiles if none is specified.
Page 811: Profile Voip Sip Callsvc Map Command
Chapter 32 profile Commands 32.21.2 profile voip sip callsvc map Command Syntax: profile voip sip callsvc map <name> This command displays which subscribers use the specified SIP call service profile. An example is shown, displaying the ports that use a SIP call service profile named “sip-cs001” (ports 1 to 38 on slot 4).
Page 812 Chapter 32 profile Commands where Has the call service profile use a VoIP key pattern. keypattern Specify the VoIP key pattern to use. <pattern- table> The call service profile does not require a password (default). nopassword The call service profile requires a password. password The call service profile’s password.
Page 813 Chapter 32 profile Commands Caller Line Identification Restriction allowed/prohibited. clir Call transferring allowed/prohibited. calltransfer The system relays fax signals according to ITU-T G.711. fax g711 The system relays fax signals according to ITU-T T-38. fax t38 Select the method the system uses to process the flash signal from a user. flash Relays flash by SIP INVITE signal.
Page 814: Profile Voip Sip Callsvc Show Command
Chapter 32 profile Commands • Flash: invite • MWI: on • Reanswer time: 0 • Numbering plan: off. • Local help: off The following example shows a command configuring a SIP call service profile named “csp1” with the following settings: •...
Page 815: Profile Voip Sip Dialplan Commands
Chapter 32 profile Commands This command displays the settings of the specified SIP call service profile, or displays the names of all call service profiles if none is specified. An example is shown next. ras> profile voip sip callsvc show callservice profile(s): ---------------------- 1.
Page 816: Profile Voip Sip Dialplan Map Command
Chapter 32 profile Commands This command removes the specified SIP dial plan profile. An example is shown to delete the call service profile named “dialplan_profile”. ras> profile voip sip dialplan delete dialplan_profile 32.22.2 profile voip sip dialplan map Command Syntax: profile voip sip dialplan map <profile>...
Page 817: Profile Voip Sip Dialplan Show Command
Chapter 32 profile Commands 32.22.4 profile voip sip dialplan show Command Syntax: profile voip sip dialplan show <profile> This command shows SIP dial plan profile or the specified SIP dial plan profile. An example is shown to display all dial plan profiles. ras>...
Page 818 Chapter 32 profile Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 819: Show Commands
H A P T E R show Commands This chapter shows you how to use the commands. show 33.1 show Commands Overview commands display runtime status information. show 33.2 Commands Summary show The following table lists the commands. The P column on the right indicates the show administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 820 Chapter 33 show Commands Table 328 show Commands (continued) COMMAND DESCRIPTION Displays port DHCP statistics. dhcp counter <slot>|<slo t-port> Displays port DHCP snooping snoop <slot-port> information. Displays the (IEEE 802.3ad) link dot3ad [<slot>] aggregation settings. Displays the status of an E1 port. status <slot-port>...
Page 821 Chapter 33 show Commands Table 328 show Commands (continued) COMMAND DESCRIPTION Displays an IMA group’s settings. groupdetail <slot- group> slot: The number of the slot where the IMA line card is installed. group: An IMA group ID. Displays an E1 line’s packet statistics. link <slot- group>...
Page 822 Chapter 33 show Commands Table 328 show Commands (continued) COMMAND DESCRIPTION Displays an E1 link’s performance link <slot- information collected during the group> specified time period. <link-id> curr15: Statistics are collected in the curr15|curr current quarter of an hour. For day|last24h example, if you use this command at r|[96q <sq>...
Page 823 Chapter 33 show Commands Table 328 show Commands (continued) COMMAND DESCRIPTION Displays line rate values. linerate <slot-port> Displays link status. linestat <slot-port> Displays loopguard status. loopguard <slot>| <slot- port>|<giga- port> Displays a port’s IEEE 802.1d MAC [<giga- address forwarding table. port>|<mac>|<slo t>|<slot- port>|vid...
Page 824 Chapter 33 show Commands Table 328 show Commands (continued) COMMAND DESCRIPTION Displays VDSL line channel linehlog <slot-port> characteristics. The format provides magnitude values in a logarithmic scale. This command displays the Quiet Line lineqln <slot-port> Noise level on a line. This is the rms (root mean square) level of the noise present on the line for a DMT tone when no ADSL or VDSL signals are...
Page 825: Show Commands
Chapter 33 show Commands Table 328 show Commands (continued) COMMAND DESCRIPTION Displays current VLANs. vlan [<vid>]|[ <start-vid> <end-vid>] Displays the status of the specified voip h248 interface H.248 interface. <id> Displays the status of the specified media <id> H.248 media card. <media>...
Page 826 Chapter 33 show Commands “dsBit table” displays the number (in hexadecimal format) of bits received per DMT tone for the downstream channel (from the DSL line card) to the subscriber’s DSL modem or router). “usSnr Table” displays the upstream (from the subscriber’s DSL modem or router to the DSL line card) Signal to Noise Ratio.
Page 827 Chapter 33 show Commands This command displays the line gain of the active ADSL line. Line gain represents the signal input required to compensate for losses in signal strength at different frequencies. ras> show adsl linegain 3-1 port 3-1: near end: (dB) tone ------ ------ ------ ------ ------ ------ ------ ------ ------ ------ 0.00...
Page 828 Chapter 33 show Commands The following table describes labels in this example. Table 330 show adsl tssi Command Display LABEL DESCRIPTION This shows the location of the line test. “near end” refers to upstream traffic, or near end/far traffic from the CPE device. “far end” refers to downstream traffic, or traffic from the CO device.
Page 829 Chapter 33 show Commands This command displays the TSSI (Transmitter Spectrum Shape Index) of transmission on the specified DSL line. This tests the variation of the actual PSD (Power Spectrum Density) from the specified PSD. ras> show adsl linetssi 3-1 port 3-1: near end: (No unit) tone...
Page 830: Show Arp Command
Chapter 33 show Commands The following table describes labels in this example. Table 332 show adsl tssi Command Display LABEL DESCRIPTION This shows the location of the line test. “near end” refers to upstream traffic, or near end/far traffic from the CPE device. “far end” refers to downstream traffic, or traffic from the CO device.
Page 831: Show Cfm Command
Chapter 33 show Commands The following example displays the ATM traffic counters for DSL port 5 on the line card in slot 7. ras> show atm 7-5 port 7-5 since pvc create since last reset -------------------- -------------------- rx cells tx cells rx rate (byte/s): tx rate...
Page 832: Show Dhcp Counter Command
Chapter 33 show Commands The following is an example. ras> show dot3ad [aggregator info] tsub: state : disable members: sub1 sub2 links syncs tup: state : disable members: up1 up2 links syncs 33.3.6 show dhcp counter Command Syntax: show dhcp counter <slot>|<slot-port> This command displays the number of DHCP related packets received on the port.
Page 833: Show Enet Command
Chapter 33 show Commands This command displays the E1 port settings on port 2 of the IMA line card installed on slot 2. ras> show e1 status 2-2 admin : In of Service frame : cascrc impedance : 120ohm alarm status: Out of CRC MF Syntax: show e1 performance <slot-port>...
Page 834 Chapter 33 show Commands The following example displays the Ethernet packet counters for the Ethernet connection to the line card in slot 1. ras> show enet up1 slot 1: link status: up rate: 1000Mbps up time: 6:08:07:50 data rate (Tx/Rx): 0/0 kbps utilization (Tx/Rx): 0/0 -------------------- -------------------- Bytes...
Page 835 Chapter 33 show Commands Table 334 show enet Command Display (continued) LABEL DESCRIPTION This is the number of good unicast frames received/transmitted. UcastPkts This is the number of good non-unicast frames received/transmitted. NUcastPkts This is the number of good multicast frames received/transmitted of 64 to 1518 MCastPkts octets in length (for non VLAN) or 1522 octets (for VLAN), not including Broadcast frames.
Page 836: Show Gbond Command
Chapter 33 show Commands 33.3.10 show gbond Command Syntax: show gbond <slot> [<gbond_name>] This command displays G.bond settings for the card inserted into the specified slot and, if specified, a G.bond group. The following example shows G.bond settings on the G.bond group named “gbondgroup1” configured on the line card in slot 5.
Page 837: Show Ima Commands
Chapter 33 show Commands This command displays the IGMP group information that is learned on the system or from the specified VLAN. ras> show igmp group [multicast group info] multicast group port slot timestamp ---- --------------- -------------------- ---------------- -------------- ras> 33.3.11.3 show igmp port info Command Syntax: show igmp port info <slot-port>...
Page 838 Chapter 33 show Commands This command displays the details of IMA group 2 on the line card installed in slot 2. ras> show ima groupdetail 2-2 Admin Status : notInService Failure state : insufficientLinksNe Symmetry : symop Near End Tx Clock Mode : itc Max Differential Delay(ms) : 25...
Page 839 Chapter 33 show Commands This command displays the status and statistics of E1 link 6 on the IMA group 2 of the line card installed in slot 2. ras> show ima link 2-2 6 Row status code NE Tx State : usable NE Rx State : unusableNoGivenReason...
Page 840 Chapter 33 show Commands This command displays the statistics of E1 link 6 in slot 2 and IMA group 2 collected during the 5th to 6th quarter hours of the past 96 quarter hours. ras> show ima performance link 2-2 6 96q 5 6 Group 2 Link 2,3 in 96 Qtr history : start from 5 to 6 idx-1 SESFE...
Page 841: Show Ip Command
Chapter 33 show Commands 33.3.13 show ip Command Syntax: show ip This command displays the management IP settings and statistics. An example is shown next. ras> show ip outband[enif0] inband[swif0] -------------- --------------- --------------- inet 192.168.0.1 123.23.19.206 netmask 255.255.255.0 255.255.255.0 broadcast 192.168.0.255 123.23.19.255 1500...
Page 842: Show Ipbpvc Interface Command
Chapter 33 show Commands The following table describes the labels in this screen. Table 336 IPB ARP Proxy Show Command Output LABEL DESCRIPTION Domain Name This field displays the name of the domain which has this ARP table. This field displays the IP address assigned to the specific device. This field displays the MAC (Media Access Control) address of the device.
Page 843: Show Lineinfo Command
Chapter 33 show Commands This command displays the (run-time) routing table(s) for the selected domain or range of IP addresses. This table includes all the entries, whether added automatically by the system or provided manually. An example is shown next. ras>...
Page 844 Chapter 33 show Commands The following table describes labels in this example. Table 337 show lineinfo Command Display LABEL DESCRIPTION This displays the connection status of the DSL link. link This is the ADSL standard that the port is using. service type Trellis coding helps to reduce the noise in ADSL transmissions.
Page 845: Show Linerate Command
Chapter 33 show Commands The following table describes labels in this example. Table 338 show lineinfo Command Display (VoIP) LABEL DESCRIPTION This shows the SIP local URI. sipLocalUri This shows the SIP remote URI. sipRemoteUri This shows the voice codec used for transmitting data. rtpTxCodecType This shows the voice codec used for receiving data.
Page 846: Show Linestat Command
Chapter 33 show Commands Table 339 Line Rate Information (continued) LABEL DESCRIPTION These are the data transfer rates (in Kbps) at which the port is receiving and actual rate sending data. These are the highest theoretically possible transfer rates (in Kbps) at which the attainable port could receive and send data.
Page 847: Show Monitor Command
Chapter 33 show Commands 33.3.21 show monitor Command Syntax: show monitor <slot> This command displays a card’s hardware monitor statistics. MSC1000G/1024G/1224G Series User’s Guide...
Page 848 Chapter 33 show Commands The following example displays the hardware monitor statistics for the card in slot 1. ras> show monitor 1 '*' indicates a current alarm voltage: volt current nominal high_lmt low_lmt ---------------- -------- -------- -------- -------- 2.5V 2.588 2.500 2.700 2.300...
Page 849: Show Mstp Command
Chapter 33 show Commands This table describes labels in the example. Table 340 show monitor Command Information LABEL DESCRIPTION The power supply for each voltage has a sensor that can detect and report the voltage voltage. This is the present voltage reading. current This field displays the average voltage measured at this sensor.
Page 850: Show Oam Command
Chapter 33 show Commands The following example displays MST region information for MST IDs 1 and 2. ras> show mstp 1 2 [mstid 1] BridgeID : 0x8001-00a0c5da46eb TimeSinceTopoChange : 3:08:23:03 TopoChangeCount TopoIsChanging : false IntRootPortID : 0x0000 IntRootID : 0x8001-00a0c5da46eb IntRootPathCost [mstid 2] BridgeID...
Page 851: Show Packet Command
Chapter 33 show Commands The following example displays Ethernet OAM details about port 13 on an Ethernet line card in slot 7. ras> show oam 7-13 Local client ------------ OAM configurations: Mode : active Remote loopback : supported Max. OAMPDU size : 1518 Operational status: Link status...
Page 852: Show Paepvc Counter Command
Chapter 33 show Commands The following example displays the hardware monitor statistics for VDSL port 5 on the line card in slot 2. ras> show packet 2-5 ifInOctets = 66240 ifInUcastPkts = 1029 ifInMcastPkts = 149 ifInBcastPkts = 202 ifInNUcastPkts = 351 ifInDiscards = 86...
Page 853: Show Paepvc Session Command
Chapter 33 show Commands The following table describes the counters. Table 341 show paepvc counter Command Fields FIELD DESCRIPTION ppp lcp config-request This field displays the number of PPP config-request packets received. ppp lcp echo-request This field displays the number of PPP echo-request packets received. ppp lcp echo-reply This field displays the number of PPP echo-reply packets received.
Page 854 Chapter 33 show Commands The following example displays the current performance counters for ADSL port 5 on the line card in slot 7. ras> show perform 7-5 curr PhysEntry --------- vtuc/vtur CurrSnrMgn = 12.5/5.5 dB vtuc/vtur CurrAtn = 1.9/0.0 dB vtuc/vtur CurrOutputPwr = 13.3/12.3 dBm vtuc/vtur CurrAttainableRate = 24989/1013 kbps...
Page 855 Chapter 33 show Commands Table 342 show performance curr (continued) LABEL DESCRIPTION These are the ADSL line’s downstream and upstream numbers of Loss of frame PerfLofs Seconds that have occurred within the current 15 minute period. These are the ADSL line’s downstream and upstream numbers of Loss of signal PerfLoss Seconds that have occurred within the current 15 minute period.
Page 856: Show Rmon Command
Chapter 33 show Commands The following example displays the one day performance counters for ADSL port 5 on the line card in slot 7. ras> show performance 7-5 1day PerfCurr1Day ------------- vtuc/vtur TimeElapsed = 57163/57163 seconds vtuc/vtur Lofs = 0/0 seconds vtuc/vtur Loss = 0/0 seconds vtuc...
Page 857 Chapter 33 show Commands This command displays subtending or uplink RMON MIB information. See RFC 1757 for information on the RMON MIBs. The following example displays RMON history information for the Gigabit Ethernet uplink 1 interface. ras> show rmon history up1 historyControlInterval = 30 seconds Index SampleIndex...
Page 858: Show Sfp Command
Chapter 33 show Commands 33.3.29 show sfp Command Syntax: show sfp <slot-port> This command displays details about the transceiver installed in an SFP slot on an Ethernet line card. The following example displays about the SFP transceiver installed in slot 13 on an Ethernet line card in slot 7.
Page 859: Show User Command
Chapter 33 show Commands ras> show sys CPU usage status: baseline 1456794 ticks ticks util ticks util ticks util ticks util 0 1356594 6.87 1 1363056 6.43 2 1337785 8.16 3 1340022 8.01 4 1187472 18.48 5 1366325 6.21 6 1377483 5.44 7 1153896 20.79...
Page 860: Show Vdsl Linedata Command
Chapter 33 show Commands The following example shows bandplan details on the VDSL line connected to port 22 of the line card in slot 2. 33.3.33 show vdsl linedata Command Syntax: show vdsl linedata <slot-port> This command displays a VDSL port’s line bit allocation. The following example shows VDSL line data on port 22 on the VDSL line card in slot 2.
Page 861: Show Vdsl Linehlog Command
Chapter 33 show Commands 33.3.35 show vdsl linehlog Command Syntax: show vdsl linehlog <slot-port> This command displays the loop response using a logarithmic scale. These values can then be used to estimate line characteristics such as line make-up and length. The following example shows hlog values on the VDSL line connected to port 22 on the line card inserted in slot 2.
Page 862: Show Vdsl Linetssi Command
Chapter 33 show Commands The following example shows the Quiet Noise Level on port 22 of the line VDSL line card in slot 2. ras> show vdsl lineqln 2-22 slot-port=2-22, DSL line qln US QLN value: --------- ------ ------ ------ ------ ------ ------ ------ ------ NA -121.0 -122.5 -126.5 -126.5 96- 103: 104- 111:...
Page 863 Chapter 33 show Commands The following example shows TSSi levels on port 22 of the VDSL line card in slot 2. ras> show vdsl linetssi 2-22 port 2-22: near end: (No unit) tone ------ ------ ------ ------ ------ ------ ------ ------ ------ ------ 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 10 : 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000 1.0000...
Page 864: Show Vlan Command
Chapter 33 show Commands 33.3.38 show vlan Command Syntax: show vlan [<vid>] show vlan <start-vid> <end-vid> This command displays the current VLANs. The following example shows VLAN 1. It is set to send untagged Ethernet frames to the Gigabit Ethernet interfaces. ras>...
Page 865: Show Voip H248 Termination Info Command
Chapter 33 show Commands This example shows the status of the H.248 interface 1’s media card 1. ras> show voip h248 media 1 1 media id media ip : 192.168.3.174 management inband ip : 172.23.19.236 management outband ip: 192.168.0.1 slot id port count : 48 state...
Page 866: Show Voip Sip Serverstate Command
Chapter 33 show Commands This example shows the H.248 termination status of the H.248 interface 1’s media card 1. ras> show voip h248 termination state 1-1-1 media id media ip port phone state line state -------- --------------- ---- ----------- ---------- 192.168.3.174 on-hook idle...
Page 867: Switch Commands
H A P T E R switch Commands This chapter shows you how to use the commands. switch 34.1 switch Commands Overview commands configure switching functions and manage the Ethernet interfaces. switch 34.2 General switch Command Parameters The following table describes commonly used command parameter notation.
Page 868 Chapter 34 switch Commands Table 347 switch Commands (continued) COMMAND DESCRIPTION Displays the bandwidth control settings. show Displays broadcast and multicast storm bcastctrl show control settings. Sets the limitations of broadcast, multicast threshold <giga-port> <bc- and unknown unicast packets, in packets limit>...
Page 869 Chapter 34 switch Commands Table 347 switch Commands (continued) COMMAND DESCRIPTION Sets an endpoint in the association. set <md-name> <ma- name> <mep-id> direction: Choose up|down. This is the active SAP direction, up means CFM <giga-port>|<slot- PDUs are sent towards relay entity and port>...
Page 870 Chapter 34 switch Commands Table 347 switch Commands (continued) COMMAND DESCRIPTION Activates DSCP-IEEE 802.1p mappings on enable this device. Sets DSCP-IEEE 802.1p mappings on this <srccp> <mapcp> device. <mappri> source code point (0~63), for srccp example: 1,3~5,10~15. mapcp: code point, 0~63 mappri: priority, 0~7 Sets the GARP timer’s Join Timer garptimer...
Page 871 Chapter 34 switch Commands Table 347 switch Commands (continued) COMMAND DESCRIPTION Sets the priority of the switch for the priority <mstid> <priority> instance ranges. The lower the number, the more likely the switch will be chosen as the root bridge. Enter 0, 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344 or 61440 in...
Page 872 Chapter 34 switch Commands Table 347 switch Commands (continued) COMMAND DESCRIPTION Activates MSTP on the port in the enable <giga-port> spanning tree instance. <mstid> Sets the path cost (0~200 000 000). Enter pathcost <giga- 0 to have the system automatically set the port>...
Page 873: Switch Bandwidth Commands
Chapter 34 switch Commands Table 347 switch Commands (continued) COMMAND DESCRIPTION Has the system assign the specified <vid> <priority> priority to traffic with the specified VLAN Displays the current setting for VLAN- show [vid] based priority or the VLAN-based priority setting for a specific VLAN ID.
Page 874: Switch Bandwidth Set Command
Chapter 34 switch Commands 34.4.3 switch bandwidth set Command Syntax: switch bandwidth set <giga-port> <ingress-rate> <egress-rate> where <giga-port> This represents Gigabit Ethernet uplink ports, subtending ports or all ports. sub1|sub2|up1|up2|all i f trunking is not enabled. Use if trunking is enabled. sub|up|all <ingress-rate>...
Page 875: Switch Bcastctrl Show Command
Chapter 34 switch Commands where This represents Gigabit Ethernet uplink ports, subtending ports or all ports. <giga-port> sub1|sub2|up1|up2|all i f trunking is not enabled. Use sub|up|all if trunking is enabled. Sets how many broadcast packets the interface is allowed to receive per <bc-limit>...
Page 876 Chapter 34 switch Commands 34.5.3.3 switch cfm lbr enable Syntax: switch cfm lbr enable <giga-port>|<slot-port> This command enables loopback testing on the specified port on a line card. The following shows an example. ras> switch cfm lbr enable 6-1 34.5.3.4 switch cfm lbr disable Syntax: switch cfm lbr disable <giga-port>|<slot-port>...
Page 877 Chapter 34 switch Commands 34.5.3.7 switch cfm ma meplist delete Syntax: switch cfm ma meplist delete <md-name> <ma-name> <mep-id> where The end point identifier. <mep-id> This command deletes a list of maintenance association end points. The following example deletes the end point identifier “2” from the list of end point identifiers for the maintenance association “ma1”...
Page 878 Chapter 34 switch Commands 34.5.3.10 switch cfm ma vlan delete Syntax: switch cfm ma vlan delete <md-name> <ma-name> <vlan-id> This command deletes a VLAN from a maintenance association. The following example deletes the VLAN identified by 3 from the maintenance association “ma1”. ras>...
Page 879 Chapter 34 switch Commands where The maintenance end point identifier. <mep-id> Choose up|down. <direction> Specify whether to send CCMs (Connectivity Check Messages) from the specified end point (down) or from (up). Select up only when the link of the specified end point is down. <priority>...
Page 880: Switch Dot3Ad Commands
Chapter 34 switch Commands This command sets a maintenance association intermediate point. The following shows an example. ras> switch cfm mip set 34.5.3.18 switch cfm show Syntax: switch cfm show [<md-name> <ma-name>] This command displays MDs, a detailed MD or a detailed MA information. Three examples (show all MDs, a specified MD’s detail, a specified MA’s detail) are shown next.
Page 881: Switch Dot3Ad Lacp Priority Command
Chapter 34 switch Commands 34.6.1 switch dot3ad lacp priority Command Syntax: switch dot3ad lacp priority <priority> where LACP system priority is a number between 1 and 65,535. The switch with <priority> the lowest system priority (and lowest port number if system priority is the same) becomes the LACP “server”.
Page 882: Switch Dot3Ad Enable Command
Chapter 34 switch Commands 34.6.4 switch dot3ad enable Command Syntax: switch dot3ad enable sub|up [lacp] where The subtending ports The uplink ports. Turns on LACP protocol. [lacp} This command turns on link aggregation on subtending or uplink ports. This example sets the MSC to use link aggregation on the subtending ports. This also copies the configuration of subtending port one to subtending port two.
Page 883: Dscp Overview
Chapter 34 switch Commands Here is an example. ras> switch dot3ad show enable type port ---- ------ ------ ----------------------------------------------- tsub static sub1 sub2 static up1 up2 “V” displays for trunking groups that have link aggregation enabled “-” displays for ports that do not.
Page 884 Chapter 34 switch Commands 34.6.8.3 switch dscp set Command Syntax: switch dscp set <giga-port> <srccp> <mapcp> <mappri> where Specify a source DiffServ Code Point (DSCP) or points, 0~63. For example: <srccp> 1,3~5,10~15 Specify the DSCP (0~63) to which you want to map the source DSCP (or <mapcp>...
Page 885: Switch Garptimer Commands
Chapter 34 switch Commands 34.7 switch garptimer Commands Use the commands to configure GARP timeout periods. switch garptimer 34.7.1 switch garptimer show Command Syntax: switch garptimer show This command displays the system’s GARP timer settings, including the join, leave and leave- all timers.
Page 886: Switch Garptimer Leaveall Command
Chapter 34 switch Commands Switches join VLANs by making a declaration. Declarations are withdrawn by issuing a Leave message. GARP timers set declaration timeout values. The following example sets the Leave Timer to 800 milliseconds. ras> switch garptimer leave 800 34.7.4 switch garptimer leaveall Command Syntax: switch garptimer leaveall <leaveall msec>...
Page 887: Switch Isolation Commands
Chapter 34 switch Commands The following example sets the Join Timer to 300 milliseconds, the Leave Timer to 900 milliseconds and the Leave All Timer to 12000 milliseconds. ras> switch garptimer join 300 900 12000 34.8 switch isolation Commands Use the commands to configure the subscriber isolation feature.
Page 888: Switch Isolation Vlan Delete Command
Chapter 34 switch Commands This command turns off the system’s subscriber isolation setting. An example is shown next. ras> switch isolation disable port isolation :enabled ras> 34.8.4 switch isolation vlan delete Command Syntax: switch isolation vlan delete <vid> where The VLAN ID [1 – 4094]. <vid>...
Page 889: Switch Mac Aging Commands
Chapter 34 switch Commands The following example turns on per-VLAN isolation for VLAN 5. ras> switch isolation vlan set 5 ras> switch isolation show port isolation :disabled isolated vlan list: ---- 34.9 switch mac aging Commands Syntax: switch mac aging set <aging time> switch mac aging show where Enter a number of seconds from 10 to 10,000.
Page 890: Switch Mstp Disable Command
Chapter 34 switch Commands The following example sets the switch to be a member of the MST region. test ras> switch mstp cfgname test 34.10.2 switch mstp disable Command Syntax: switch mstp disable This command deactivates the MSTP feature on the switch. 34.10.3 switch mstp enable Command Syntax: switch mstp enable...
Page 891: Switch Mstp Maxhops Command
Chapter 34 switch Commands The following example sets the maximum age to 20 seconds. ras> switch mstp maxage 20 34.10.7 switch mstp maxhops Command Syntax: switch mstp maxhops <max-hops> This command sets the number of hops (between 1 and 255) in an MSTP region before the BPDU is discarded and the port information is aged.
Page 892: Switch Mstp Show Command
Chapter 34 switch Commands 34.10.10 switch mstp show Command Syntax: switch mstp show This command displays the general MSTP settings on the switch. The following figure shows an example. ras> switch mstp show config name : test revision level status : disabled priority : 32768...
Page 893: Switch Mstp Vlanmap Command
Chapter 34 switch Commands 34.10.12 switch mstp vlanmap Command Syntax: switch mstp vlanmap <mstid> <start_vid> <end_vid> where = Index number (between 0-16) to identify a spanning tree instance. For CIST, <mstid> enter 0. To identify an MSTI, enter a number between 1 and 16. = Start of the VLAN range.
Page 894: Switch Oam Port Mode Command
Chapter 34 switch Commands This command turns on OAM functionality for the selected Ethernet line card port. The following example turns on OAM functionality for port 13 on the Ethernet line card in slot 7. ras> switch oam port enable 7-13 34.11.3 switch oam port mode Command Syntax: switch oam port mode <slot-port>...
Page 895: Switch Port Commands
Chapter 34 switch Commands This command displays the Ethernet line card’s OAM settings. The following example enables displays the OAM settings on the Ethernet line card in slot 7. ras> switch oam show 7 port en mode rmtlpbk ==== == ======== ======= passive passive passive...
Page 896: Switch Port Flowctrl Disable Command
Chapter 34 switch Commands The following example turns on the subtending 1 Gigabit Ethernet interface. ras> switch port enable sub1 34.12.3 switch port flowctrl disable Command Syntax: switch port flowctrl disable <giga-port> This command turns off flow control on a Gigabit Ethernet interface. The following example turns off the flow control on the subtending 1 Gigabit Ethernet interface.
Page 897: Switch Port Mode Command
Chapter 34 switch Commands 34.12.6.1 switch port gvrp disable Command Syntax: switch port gvrp disable <giga-port> This command turns off GVRP on a Gigabit Ethernet interface. GVRP (GARP VLAN Registration Protocol) is a registration protocol that defines a way for switches to register necessary VLAN members on ports across the network.
Page 898 Chapter 34 switch Commands This command disables MSTP on the specified Gigabit Ethernet interface port (or all of them) in the specified spanning tree instance. All MSTP packets to/from the specified spanning tree instance will be dropped on the port. The following example disables MSTP on unlink port 1 in spanning tree instance 2.
Page 899 Chapter 34 switch Commands The following example activates point-to-point link on uplink port 2. ras> switch port mstp p2plink up2 enable 34.12.8.5 switch port mstp pathcost Command Syntax: switch port mstp pathcost <giga-port> <mstid> <cost> This command sets the path cost of the specified Gigabit Ethernet interface in the spanning tree.
Page 900: Switch Port Name Command
Chapter 34 switch Commands 34.12.9 switch port name Command Syntax: switch port name <giga-port> <name> where A name to identify the port. <name> This command sets the name of a Gigabit Ethernet interface. The following example sets the name of uplink interface 1 to ras>...
Page 901: Switch Port Show Command
Chapter 34 switch Commands 34.12.12 switch port show Command Syntax: switch port show This command displays the settings for the system’s Gigabit Ethernet interfaces. An example is shown next. ras> switch port show port name mode speed pvid prio gvrp ftype dscp ----- --------------- ---- ---- ------ ---- ---- ---- ---- ----- ---- ---- sub1 Subtend1...
Page 902: Switch Port Vlantrunk Disable Command
Chapter 34 switch Commands where This represents Gigabit Ethernet uplink ports, subtending <giga-port> ports or all ports. Use sub1|sub2|up1|up2|all i trunking is not enabled. Use tsub|tup|all trunking is enabled. This command sets a Gigabit Ethernet interface(s) to use VLAN trunking in order to accept frames with any VID.
Page 903: Switch Qschedule Show Command
Chapter 34 switch Commands where Strict Priority Queuing (SPQ) services queues based on priority only. When the highest priority queue empties, traffic on the next highest- priority queue begins. Weighted Round Robin services queues based on their priority and queue weight. WRR is activated only when a port has more traffic than it can handle.
Page 904: Switch Queuemap Show Command
Chapter 34 switch Commands This command sets the system to use a particular queue for traffic of a specific IEEE 802.1p priority. The following example sets the system to use queue 3 for traffic with priority 3. ras> switch queuemap set 3 3 34.15.2 switch queuemap show Command Syntax: switch queuemap show...
Page 905: Chapter 35 Sys Commands
H A P T E R sys Commands This chapter shows you how to use the commands. 35.1 sys Commands Overview commands are for system management and maintenance. 35.2 Commands Summary The following table lists the commands. The P column on the right indicates the administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 906 Chapter 35 sys Commands Table 348 sys Commands (continued) COMMAND DESCRIPTION Enables accounting of administrative enable sessions via SSH, Telnet and console port <radius|tacacs+> and specifies the mode and protocol <start-stop|stop- method. Optionally, sends accounting only> <broadcast> information for administrative sessions via SSH, Telnet and console port to all configured accounting servers at the same time (1 or 0).
Page 907 Chapter 35 sys Commands Table 348 sys Commands (continued) COMMAND DESCRIPTION Specifies how the system decides which mode index- RADIUS server to select if you configure priority|round- multiple servers. robin index-priority: The system tries to authenticate with the first configured RADIUS server.
Page 908 Chapter 35 sys Commands Table 348 sys Commands (continued) COMMAND DESCRIPTION Specifies how the system decides which mode index- TACACS+ server to select if you configure priority|round- multiple servers. robin index-priority: The system tries to authenticate with the first configured TACACS+ server.
Page 909 Chapter 35 sys Commands Table 348 sys Commands (continued) COMMAND DESCRIPTION Sets the system name. hostname <hostname> Sets the geographic location of the location <location> system. Displays general system and system show information. Sets hardware monitor alarm thresholds. monitor <slot> <volt|temp|fan|cpu volt: Voltage |mem|pbuf>...
Page 910 Chapter 35 sys Commands Table 348 sys Commands (continued) COMMAND DESCRIPTION Sets the IP addresses and listening ports trapdst <index> for up to four SNMP trap server IP <destination> addresses and listening ports. Set 0.0.0.0 [<port>] to not send any SNMP traps. [v1|v2c|v3] name: username to be included in trap...
Page 911: Sys Commands
Chapter 35 sys Commands Table 348 sys Commands (continued) COMMAND DESCRIPTION Gets the time and date from a predefined sync time server. Selects which database the switch uses to user auth <mode> authenticate a user. : local, : radius, local then radius, 4: TACACS+, 5: local then TACACS+, 6: radius then local, 7: tacas+ then local Removes a user account.
Page 912: Sys Baud Set Command
Chapter 35 sys Commands This command displays general information about the system such as the model name and firmware version. This is an example. ras> sys version [master card version info] product model : MSC1000G system up time 1:00:13:39 f/w version : V3.70(LU.0) | 11/29/2006 bootbase version: VLU1.02 | 04/01/2005 database version : 09:16:57 2006/12/14...
Page 913: Sys Client Enable Command
Chapter 35 sys Commands 35.3.5 sys client enable Command Syntax: sys client enable <index> This command turns on a secured client set. The following example turns on secured client set 1. ras> sys client enable 1 35.3.6 sys client disable Command Syntax: sys client disable <index>...
Page 914: Sys Time Set Command
Chapter 35 sys Commands This command displays the system’s current time. An example is shown next. ras> sys time show current time is 17:57:01 ras> 35.3.9 sys time set Command Syntax: sys time set <hh> [<mm> [<ss>]] This command sets the system’s time. An example is shown next. ras>...
Page 915: Sys Timeserver Set Command
Chapter 35 sys Commands 35.3.13 sys timeserver set Command Syntax: sys timeserver none sys timeserver daytime <ip-address> [sync] sys timeserver time|ntp <ip-address> <utc[<+|->0100~1200]> [sync] where Sets the system to not use a time server. none The Daytime time service protocol (RFC 867). When you select this daytime format, the switch displays the day, month, year and time with no time zone adjustment.
Page 916: Sys Info Contact Command
Chapter 35 sys Commands where The chassis number (an integer from 1 to 64). The chassis number <chassis> helps to keep track of this individual unit in a multiple unit application. This command sets the system chassis number. The following example sets the system’s chassis number to 3. ras>...
Page 917: Sys Info Location Command
Chapter 35 sys Commands where A descriptive name for identification purposes. This name can be up to <hostname> 30 alphanumeric characters long. This command sets the system name. The following example sets “OurSystem” as the system’s name. ras> sys info hostname OurSystem 35.3.19 sys info location Command Syntax: sys info location <location>...
Page 918: Sys Monitor Set Command
Chapter 35 sys Commands 35.3.21 sys monitor set Command Syntax: sys monitor set <slot> <volt|temp|fan|cpu|mem|pbuf> <index> <high-limit> <low-limit> where The main chassis slot where the card is located. Use the slot number of <slot> the MSC when you configure the fan, memory, or packet buffer limits. volt: Set the voltage tolerance range.
Page 919: Sys Monitor Show Command
Chapter 35 sys Commands A sensor’s maximum voltage, temperature, fan RPM, or utilization limit. <high-limit> The maximum voltage for each voltage sensor must be within the following ranges. Measured in millivolts (mV). MSC: 1 = 2575~2750, 2 = 1287~1375, 3 = 3399~3630, 4 = 1339~1430, 5 = 15450~16500 ADSL line card: 1 = 1236~1320, 2 = 1854~1980, 3 = 3399~3630, 4 = 21115~22550...
Page 920: Sys Multilogin Enable Command
Chapter 35 sys Commands The following example shows the MSC statistics. ras> sys monitor show 1 '*' indicates a current alarm voltage: volt current nominal high_lmt low_lmt ---------------- -------- -------- -------- -------- 2.5V 2.571 2.500 2.700 2.300 1.25V 1.242 1.250 1.350 1.150 3.3V...
Page 921: Sys Multilogin Disable Command
Chapter 35 sys Commands The following is an example. ras> sys multilogin enable 35.3.24 sys multilogin disable Command Syntax: sys multilogin disable This command turns off multiple login. The following is an example. ras> sys multilogin disable 35.3.25 sys multilogin show Command Syntax: sys multilogin show This command displays the multiple login setting.
Page 922: Sys Server Port Command
Chapter 35 sys Commands The following example shows the administrator at IP address 123.23.19.11 ordering a reboot to occur after 1200 seconds, displaying the reboot schedule and then canceling the reboot. ras> sys reboot 1200 telnet-1(123.23.19.11) has initiated reboot, system reboot in 1200 seconds! ras>...
Page 923: Sys Server Show Command
Chapter 35 sys Commands 35.3.30 sys server show Command Syntax: sys server show This command displays the system’s service access control settings. The following is an example. ras> sys server show server status port ------ ------ ----- telnet icmp snmp ras>...
Page 924: Sys Snmp Trapcommunity Command
Chapter 35 sys Commands The following example sets the password for incoming Set- requests to “Set123”. ras> sys snmp setcommunity Set123 35.4.3 sys snmp trapcommunity Command Syntax: sys snmp trapcommunity <community> where The password sent with each trap to the SNMP manager. <community>...
Page 925: Sys Snmp Show Command
Chapter 35 sys Commands 35.4.5 sys snmp show Command Syntax: sys snmp show This command displays the current SNMP get community, set community, trap community and trap destination settings. The following is an example. ras> sys snmp show [community] get community : Get123 set community : Set123 trap community: public [trap destination]...
Page 926: Sys Snmp Version Command
Chapter 35 sys Commands 35.4.7 sys snmp version Command Syntax: sys snmp version v2c|v3|v3v2c where Sets the SNMP version and access mode. v2c|v3|v3v2c : SNMPv2 read/write : SNMPv3 read/write with additional user authentication and data encryption options. : SNMPv3 read/write and SNMPv2 read-only. v3v2c This command sets the system to use the specified SNMP version and access mode.
Page 927: Sys Syslog Disable Command
Chapter 35 sys Commands This command sets the system to send logs to an external syslog server. An example is shown next. ras> sys syslog enable 35.5.3 sys syslog disable Command Syntax: sys syslog disable This command sets the system to not send logs to an external syslog server. An example is shown next.
Page 928: Sys User Server Command
Chapter 35 sys Commands where Sets which database the switch uses to authenticate a user. <mode> : local : radius : local then radius 4: TACACS+ 5: local then TACACS+ 6: radius then local 7: tacas+ then local This command sets which database the system uses to authenticate a user. The following example sets the system to check a user’s username and password against the local database.
Page 929: Sys User Set Command
Chapter 35 sys Commands The following example sets a RADIUS server IP address of 192.168.1.77, port number of 1813 and password of “pwd1234”. The account is assigned a privilege if no service medium type information is received from the RADIUS server. ras>...
Page 930: Sys User Disable Command
Chapter 35 sys Commands where The user name for the account <name> This command turns on an administrator account. The following example turns on the “bob” administrator account. ras> sys user enable bob 35.6.6 sys user disable Command Syntax: sys user disable <name> where The user name for the account <name>...
Page 931 Chapter 35 sys Commands The following is an example. * denotes your session. ras> sys user online [session info ('*' denotes your session)] session user remote ip login time ---------- ---------------- --------------- ------------------- *telnet admin 123.23.19.11 13:08:27 2005/06/09 ras> MSC1000G/1024G/1224G Series User’s Guide...
Page 932 Chapter 35 sys Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 933: Chapter 36 Vlan Commands
H A P T E R vlan Commands This chapter shows you how to use the commands. vlan 36.1 vlan Commands Overview commands are for static VLAN management. vlan 36.2 Commands Summary vlan The following table lists the commands. The P column on the right indicates the vlan administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 934: Vlan Disable Command
Chapter 36 vlan Commands The following example removes static VLAN entry 27. ras> vlan delete 27 36.3.2 vlan disable Command Syntax: vlan disable <vid> This command turns off the static VLAN. The following example turns off static VLAN entry 27. ras>...
Page 935: Vlan Show Command
Chapter 36 vlan Commands where The VLAN ID [1 – 4094]. <vid> This represents Gigabit Ethernet uplink ports, subtending ports or all <giga-port> ports. Use sub1|sub2|up1|up2|all i f trunking is not enabled. if trunking is enabled. sub|up|all fix: Makes the port a permanent member of this VLAN group. fix|forbid|normal : Prohibits the port from joining this VLAN group.
Page 936 Chapter 36 vlan Commands MSC1000G/1024G/1224G Series User’s Guide...
Page 937: Chapter 37 Voip Commands
H A P T E R voip Commands This chapter describes the Voice over IP management commands. 37.1 voip Commands Summary The following table lists the commands. The P column on the right indicates the voip administrator privilege level needed to use the command (H for high, M for middle or L for low).
Page 938 Chapter 37 voip Commands Table 351 voip Commands (continued) COMMAND DESCRIPTION Has the signaling card start MG mg enable <id> operation and attempt to register with the MGC. Sets the MG name, H.248 profile mg set <id> it uses, and port number the <mg-name>...
Page 939 Chapter 37 voip Commands Table 351 voip Commands (continued) COMMAND DESCRIPTION Defines the keys a subscriber sip keypattern <name> presses to access a particular call <service-type> service. <pattern> Lists the configured keypattern show [name] profiles or displays the settings of the specified profile.
Page 940 Chapter 37 voip Commands Table 351 voip Commands (continued) COMMAND DESCRIPTION Displays the routing table for the show <slot> specified slot. Removes the specified sip numberplan delete <name> numberplan table. Displays the SIP call service [<name>] profile(s) that refer to the specified numbering plan.
Page 941: Voip Arp Commands
Chapter 37 voip Commands 37.2 voip arp Commands Use these commands to control ARP (Address Resolution Protocol) on the VoIP line cards. 37.2.1 voip arp flush Command Syntax: voip arp flush <slot> This command removes all ARP (Address Resolution Protocol) table entries stored in the specified VoIP line card.
Page 942: Voip Countrycode Set Command
Chapter 37 voip Commands 37.3.1 voip countrycode set Command Syntax: ras> voip countrycode set <country>|<countrycode> where <country> <countrycode> <country> <countrycode> japan germany taiwan greece austria australia belgium new zealand 26 bulgaria hong kong czech singapore denmark morocco finland ireland france malaysia hungary russia...
Page 943 Chapter 37 voip Commands This command displays the PSTN parameters for which the VoIP line card is currently configured. An example is shown next. ras> voip countrycode show (country, countrycode) = (usa, 0) : ulaw impedance : 600ohm loop current : 25 mA tax type : metering...
Page 944: Voip H248 Commands
Chapter 37 voip Commands 37.4 voip h248 Commands Use these commands to manage the VoIP line cards. 37.4.1 voip h248 interface bhca command Syntax: voip h248 interface bhca <id> <peak> <average> where The maximum number of call attempts per second (0~30). peak average The maximum number of call attempts for an hour (0~60000).
Page 945: Voip H248 Interface Mg Disable Command
Chapter 37 voip Commands The following example configures H.248 interface 1 to use IP address 10.59.3.2, subnet mask 255.255.225.0, and VLAN ID 1. ras> voip h248 interface ip 1 10.59.3.2/24 1 37.4.4 voip h248 interface mg disable command Syntax: voip h248 interface mg disable <id> Use this command to have the specified H.248 interface’s signaling card stop MG operation and de-register from the MGC.
Page 946: Voip H248 Interface Slave Command
Chapter 37 voip Commands Use this command to see H.248 interface settings. Specify an interface’s ID to see details about that interface. The following example shows H.248 interface 1’s settings. ras> voip h248 interface show 1 ip/mask : 172.23.19.200/24 primary slot secondary slot : 6 mg name : MG1...
Page 947: Voip H248 Opmode Command
Chapter 37 voip Commands The following example sets a media VOP in slot 3 to use the VOP card at IP address 192.168.3.174 as the primary signaling card and no secondary signaling card. ras> voip h248 master 3 192.168.3.174 0.0.0.0 37.4.10 voip h248 opmode command Syntax: voip h248 opmode <slot>...
Page 948: Voip H248 Command Examples
Chapter 37 voip Commands Here is an example. ras> voip h248 show 3 slot opmode : mc pbit dscp : 48 master ip1 : 0.0.0.0 master ip2 : 0.0.0.0 37.5 voip h248 Command Examples Here are some examples of using commands to configure H.248. 37.6 Single VOP Card voip h248 Command Example Here is an example of configuring the IES to use a single VOP card in slot 3 as both the signaling card and a media card.
Page 949: Adding Another Vop Card Voip H248 Command Example
Chapter 37 voip Commands Sets the VOP card in slot 3 to use the VOP card at IP address 192.168.3.174 as the primary signaling card and no secondary signaling card. ras> voip h248 interface ip 1 172.16.19.200/24 1 Sets H.248 interface 1 to use IP address 172.16.19.200, subnet mask 255.255.225.0, and VLAN ID 1.
Page 950: Voip Ip Commands
Chapter 37 voip Commands ras> voip h248 opmode 4 mc Sets the VOP card in slot 4 to function as a media card. ras> voip h248 master 4 192.168.3.174 0.0.0.0 Sets the VOP card in slot 4 to use the VOP card at IP address 192.168.3.174 as the primary signaling card and no secondary signaling card.
Page 951: Voip Ip Show Command
Chapter 37 voip Commands 37.8.3 voip ip show Command Syntax: voip ip show <slot> This command shows the IP address, VLAN ID and DNS server IP address used by the specified VoIP line card. The following example shows the information for the VoIP line card in slot 4. ras>...
Page 952: Voip Route Show Command
Chapter 37 voip Commands The IP address of the gateway that you want to send the packets through. <gateway-ip> The metric (hop count) of this static route. [<metric>] This command defines a new, static IP forwarding route for VoIP traffic on the specified slot, or edits an existing one.
Page 953: Voip Sip Dialplan Set Command
Chapter 37 voip Commands This command displays settings for all SIP profiles configured on this line card, or settings for the SIP protocol profile(s) that refer to specified dial plan table. An example is shown next. ras> voip sip dialplan map dialplan1 Dial plan profile(s) list that refer to "dialplan1"...
Page 954: Voip Sip Dialplan Show Command
Chapter 37 voip Commands where The dial plan table name (<32 characters). <name> The pattern of dialed digits to which this dialplan refers: <pattern> The pattern must be 64 characters or fewer in length. Allowed telephone characters are: digits 0~9, “*” and “#”. Allowed function characters are: “x”, “.”, “|”, “!”, “~”, “,”...
Page 955: Voip Sip Keypattern Commands
Chapter 37 voip Commands This command displays the dial plans configured on this line card when no dialplan is specified, and the contents of a dial plan table when specified. An example is shown next. ras> voip sip dialplan show Dialplan Name(s): ---------------------- 1.
Page 956 Chapter 37 voip Commands where The name of the keypattern profile (<=32 characters). [name] If a keypattern profile is not specified, this commands lists configured keypattern profiles. When a profile is specified this command shows the settings of the specified profile, in this case the default keypattern profile “DEFVAL”.
Page 957: Voip Sip Localhelp Commands
Chapter 37 voip Commands Enter the sequence of keys the user presses to restrict his/her phone clir number by not sending caller ID information (1~7 characters). Enter the sequence of keys the user presses to turn off Do Not dndoff Disturb (1~7 characters).
Page 958: Voip Sip Localhelp Set Command
Chapter 37 voip Commands 37.12.3 voip sip localhelp set Command Syntax: voip sip localhelp set <name> <index> [<tel-number>] where The local help table name (<=32 characters). <name> The index number of an entry in the emergency table (1~16). <index> The telephone number entry (<=16 digits). <tel-number>...
Page 959: Voip Sip Numberplan Map Command
Chapter 37 voip Commands 37.13.2 voip sip numberplan map Command Syntax: voip sip numberplan map [<name>] This command displays which SIP call service profiles refer to the specified SIP numbering plan table. An example is shown, displaying the SIP call service profiles that map to a numbering plan table named “numplan_table”.
Page 960 Chapter 37 voip Commands The following example shows a command defining a rule (number 1 in the numberplan “cx”) that replaces the dialed number “002(*)” with the numbers enclosed by the parentheses. In this example, a dialed number “0024401473123456” would be translated to “4401473123456”. ras>...
Page 961: Firmware And Configuration File Maintenance
H A P T E R Firmware and Configuration File Maintenance This chapter tells you how to upload a new firmware file and how to upload and download configuration files. 38.1 Firmware and Configuration File Maintenance Overview The system’s built-in FTP (and SFTP) servers allow you to use any FTP (or SFTP) client (for example, ftp.exe in Windows) to upgrade card firmware or system configuration files.
Page 962: Editable Configuration File
Chapter 38 Firmware and Configuration File Maintenance This is a sample from a FTP session to transfer the MSC’s current configuration file (including the configuration files of all the line cards) to the computer file config.dat If your FTP or SFTP client does not allow you to have a destination filename different than the source, you will need to rename them as the MSC only recognizes “config-0”...
Page 963: Edit Configuration File
Chapter 38 Firmware and Configuration File Maintenance Quit FTP. ftp> quit 38.3.2 Edit Configuration File Open the file via a text editor (see the following example) and edit to the desired config.dat configuration. Ensure that any changes you make to the commands in the configuration file correspond to the commands documented in this User’s Guide.
Page 964: Firmware File Upgrade
Chapter 38 Firmware and Configuration File Maintenance Enter the management password (1234 by default). Password: 1234 230 Logged in ftp> put xxx.dat config-0 Quit FTP. ftp> quit Wait for the update to finish. The system restarts automatically. 38.4 Firmware File Upgrade Use the following procedure to upload firmware to the management switch card or DSL line card(s).
Page 965: Configuration File Upgrade
Chapter 38 Firmware and Configuration File Maintenance • Use this command to transfer the firmware file to the management switch card that you are using (the internal firmware file is named ras) ftp> put firmware.bin ras • Use this command to transfer the firmware file to a line card or the management switch card that you are not currently using.
Page 966 Chapter 38 Firmware and Configuration File Maintenance MSC1000G/1024G/1224G Series User’s Guide...
Page 967: Part Iv: Troubleshooting And Product Specifications
Troubleshooting and Product Specifications Troubleshooting (969) Product Specifications (979)
Page 969: Chapter 39 Troubleshooting
39 . H A P T E R Troubleshooting This chapter offers some suggestions to solve problems you might encounter. The potential problems are divided into the following categories. See Chapter 40 on page 979 for default settings. 39.1 Power, Hardware Connections, and LEDs The MSC does not turn on.
Page 970: Msc Access And Login
Chapter 39 Troubleshooting 1 Make sure you understand the normal behavior of the LED. See Section 2.2 on page 2 Check the hardware connections. See Section 2.3 on page 3 Inspect your cables for damage. Replace any damaged cables. 4 If the problem continues, contact the vendor. A Gigabit Ethernet interface’s LEDs are not on.
Page 971 Chapter 39 Troubleshooting I forgot the password. 1 The default password is 1234. 2 Contact customer support for how to reset your device to the factory defaults if you have forgotten the password. I cannot see or access the Login screen in the web configurator. 1 Make sure you are using the correct IP address.
Page 972 Chapter 39 Troubleshooting I cannot use FTP to upload / download the configuration file. / I cannot use FTP to upload new firmware. (edit as needed) See the troubleshooting suggestions for I cannot see or access the Login screen in the web configurator.
Page 973: Configuration
Chapter 39 Troubleshooting 39.3 Configuration Configuration changes were not saved after I restarted the system. Use Config Save when you are done with a configuration session. 39.4 Data Transmission The Gigabit Ethernet interface’s LED is on, but data cannot be transmitted. 1 Ping the MSC from a computer behind the connected uplink or downlink Ethernet device.
Page 974: Redundant Management Switch Cards
Chapter 39 Troubleshooting 39.5 Redundant Management Switch Cards I cannot get a redundant (second) management switch card to work as a standby. 1 Make sure that the management switch cards are in slots 1 and 2 of the IES-5000 main chassis or slots 8 and 9 of the IES-6000 main chassis.
Page 975: Resetting The Defaults
Chapter 39 Troubleshooting It is normal for a line card to be in the inactive state when it is starting up or the firmware is being upgraded. If neither of these is the case, the line card may be malfunctioning. Try the following.
Page 976: Ima Connnection Failure
Chapter 39 Troubleshooting This procedure is for emergency situations only. 1 Obtain the firmware file, unzip it and save it in a folder on your computer. 2 Connect your computer to the console port and use terminal emulation software configured to the following parameters: •...
Page 977 Chapter 39 Troubleshooting 1 Make sure all physical connections between your TDM network and your IMA devices are connected properly. (Refer to IMA Application page 45.) This includes that you are using correct E1 wires and have your Tx connect to the Rx wire from the TDM network and your Rx connect to the Tx wire from the TDM network.
Page 978 Chapter 39 Troubleshooting MSC1000G/1024G/1224G Series User’s Guide...
Page 979: Product Specifications
H A P T E R Product Specifications This appendix gives details about the IES default settings and MSC hardware and features. 40.1 IES Default Settings This table lists major default settings. Table 354 Default Settings Default In-band IP Address 192.168.1.1 Default In-band Subnet Mask 255.255.255.0 (24 bits)
Page 980 Chapter 40 Product Specifications Table 354 Default Settings Rate Adaptation Mode Startup Startup Up Shift Margin 15 db 15 db Down Shift Margin 9 db 9 db SHDSL Profile Default Settings Name: DEFVAL Maximum Rate 2304 Kbps Minimum Rate 192 Kbps Annex Mode annex b Wire Pair...
Page 981 Chapter 40 Product Specifications Table 354 Default Settings Up-shift SNR Margin 90 in 0.1dB 90 in 0.1dB Down-Shift SNR Margin 90 in 0.1dB 90 in 0.1dB Up-Shift Time 30 in 0.1dB 30 in 0.1dB Down-Shift Time 30 in 0.1dB 30 in 0.1dB Target SNR Margin 60 in 0.1dB 60 in 0.1dB...
Page 982 Chapter 40 Product Specifications Table 354 Default Settings Name: DEFVAL Upstream Settings: Downstream Settings: Minimum Data Rate 192 in kbps 192 in kbps Maximum Data Rate 100032 in kbps 100032 in kbps Interleave Delay 8 in msec 8 in msec Impulse Noise Protection 4 in 0.5 symbols 4 in 0.5 symbols...
Page 983: Specifications
Chapter 40 Product Specifications Table 354 Default Settings G.711 Local call VoIP Default Regional Settings Countrycode USA (0) Default ATM Profile Settings Name: DEFVAL Traffic Class: PCR: 300000 cell/sec. CDVT: Virtual Channel Default Settings VPI: VCI: Multiplexing: LLC-based PVID: Priority ATM Profile: DEFVAL Default IGMP Filter Profile Settings...
Page 984 Chapter 40 Product Specifications Table 355 MSC Specifications MSC1000G Ethernet Four 1000M interfaces (two SFP and two combo). Network Interfaces Load sharing IEEE 802.3ad static (no LACP) Load sharing IEEE 802.3ad with LACP IEEE 802.1s Multiple Spanning Tree Configurable uplink and subtending modes Two SFP modules Provides connection for Small Form-factor Pluggable (SFP) transceiver modules (Gigabit Ethernet only) that comply with INF-8074i.
Page 985 Chapter 40 Product Specifications Table 355 MSC Specifications MSC1224G Ethernet 2 x 10G Ethernet uplink ports Network Interfaces • 2 optical fiber port (XFP module) for uplink traffic aggregation. Port 1 & 2, which provides INF-8077i compatible connection for XFP transceiver module (10 Gigabit Ethernet).
Page 986 Chapter 40 Product Specifications Table 355 MSC Specifications Storage Environment -40 ~ 70 degrees C 10% ~ 95% RH (non-condensing) Certifications MSC1000G CE Conformity ITU-T K.20 Safety IEC 60950-1 EN 60950-1 CSA 60950-1 UL 60950-1 NEBS Level 3 EN 300386 EN 55022 EN 61000-3-2 EN 61000-3-3...
Page 987: Features
Chapter 40 Product Specifications 40.3 Features This section introduces the IES-5000 features. Table 356 IES-5000 Features Basic Function Power-On System Test (POST) LED display (SYS/ST/ALM) Uplink Interface Gigabit Ethernet Thermal cutoff protection Temperature and voltage monitoring and threshold setting Management Features Command Line Interface (CLI) DSL profile function for managing DSL line card connections Firmware upgrade through FTP or SFTP and serial console port...
Page 988 Chapter 40 Product Specifications Table 356 IES-5000 Features (continued) VLAN VLAN cross-connect VLAN cross-connect: map DSL line (VPI/VCI) to one VLAN (maximum 4K VLAN) Residential bridging: user to user traffic can be blocked VLAN Tag-based Transparent LAN Service (TLS) or Q-in-Q/VLAN stacking Number of VLAN IDs: 4096 MAX number of VLAN + MAC per ADSL port: 256 UI Isolation...
Page 989 Chapter 40 Product Specifications Table 356 IES-5000 Features (continued) Multicast Features IP multicast forwarding IGMP Proxy IGMP v1, v2, and v3 Snooping v1&v2 (port based) VLAN-aware IGMP snooping IGMP multicast channel limiting by group count or bandwidth usage Static multicast addresses 128 Broadcast methodology IGMP membership reports All video group address are configured in the system...
Page 990 Chapter 40 Product Specifications Table 356 IES-5000 Features (continued) Per DSL Port Per port limitations: Provisioning Number of ACL Profile: 8 Number of DHCP snooping table entries: 32 Number of static DHCP snooping table entries: 3 Number of MAC filters: 10 Number of MVLAN: 4 Number of OUI Filter: 10 Number of PVCs (PVC, PPVC member, TLS PVC, PAEPVC): 8...
Page 991: Firmware Naming Conventions
Chapter 40 Product Specifications Table 357 Supported Standards (continued) STANDARD DESCRIPTION RFC 1213 Simple Network Management Protocol (SNMP) RFC 1573 RFC 1757 RFC 2662 RFC 2665 RFC 2674 RFC 2863 RFC 3440 RFC 3635 RFC 3636 RFC 1483 Multiprotocol Encapsulation over ATM Adaptation Layer 5 RFC 2131 Dynamic Host Configuration Protocol (DHCP) RFC 2132...
Page 992: Console Port Pin Assignments
Chapter 40 Product Specifications 40.5 Console Port Pin Assignments In a serial communications connection, generally a computer is DTE (Data Terminal Equipment) and a modem is DCE (Data Circuit-terminating Equipment). The MSC is DCE when you connect a computer to the console port. Figure 398 Console Port Pin Layout Table 358 Console Port Pin Assignments CONSOLE PORT RS –...
Page 993 Chapter 40 Product Specifications Table 359 ALARM Connector Pin Assignments DESCRIPTION Common pin for alarm input 1 Common pin for alarm input 2 Common pin for alarm input 3 Normal close for minor alarm output Normal open for minor alarm output Common pin for major alarm output Normal close for critical alarm output Normal open for critical alarm output...
Page 994 Chapter 40 Product Specifications MSC1000G/1024G/1224G Series User’s Guide...
Page 995: Part V: Appendices And Index
Appendices and Index Legal Information (1069) Index (1073)
Page 997: Appendix A Pstn Parameters By Country
P P E N D I X PSTN Parameters by Country Country Code: 0,usa law: ulaw impedance: 600ohm loop current: 25 mA tax type: metering Ring parameters: frequency: 20.0 Hz amplitude: 53.0 Vrms onTime1: 2.00 seconds offTime1: 4.00 seconds onTime2: 2.00 seconds offTime2: 4.00 seconds Pulse parameters: flashMin: 90 ms...
Page 998 Appendix A PSTN Parameters by Country Caller ID parameters: CID type: during ring payload type: MDMF first TAS type: NULL second TAS type: NULL first TAS interval: 0 ms second TAS interval: 0 ms start to ring: 500 ms (prior ring only) Tones parameters: dial tone: 350+440Hz -18.0dB continuous ring back tone: 440+480Hz -18.0dB on 2.000s off 4.000s...
Page 999 Appendix A PSTN Parameters by Country offTime1: 2.00 seconds onTime2: 1.00 seconds offTime2: 2.00 seconds Pulse parameters: flashMin: 90 ms flashMax: 620 ms breakMin: 47 ms breakMax: 80 ms makeMin: 30 ms makeMax: 55 ms interDigitMin: 250 ms Meter parameters: frequency: 12 kHz onTime: 200 ms offTime: 200 ms...
Page 1000 Appendix A PSTN Parameters by Country howler tone: 1400+2060+2450+2600Hz -3.0dB on 0.100s off 0.100s warning tone: 1400Hz -18.0dB on 0.500s off continuous confirmation tone: 400Hz -18.0dB on 0.125s off 0.125s 400Hz -18.0dB on 0.125s off 0.625s holding tone: 440+480Hz -18.0dB on 0.500s off 0.500s 350+440Hz -18.0dB on 0.500s off 2.500s Taiwan Country Code: 2,taiwan...
Page 1001 Appendix A PSTN Parameters by Country Caller ID parameters: CID type: prior ring payload type: MDMF first TAS type: DT-AS second TAS type: NULL first TAS interval: 300 ms second TAS interval: 0 ms start to ring: 400 ms (prior ring only) Tones parameters: dial tone: 350+440Hz -13.0dB continuous ring back tone: 440+480Hz -19.0dB on 1.000s off 2.000s...
Page 1002 Appendix A PSTN Parameters by Country Ring parameters: frequency: 50.0 Hz amplitude: 53.0 Vrms onTime1: 1.00 seconds offTime1: 5.00 seconds onTime2: 1.00 seconds offTime2: 5.00 seconds Pulse parameters: flashMin: 90 ms flashMax: 500 ms breakMin: 47 ms breakMax: 80 ms makeMin: 30 ms makeMax: 55 ms interDigitMin: 250 ms...
Page 1003 Appendix A PSTN Parameters by Country congestion tone: 420Hz -18.0dB on 0.200s off 0.200s call waiting tone #1: 420Hz -18.0dB on 0.040s off 1.950s call waiting tone #2: 420Hz -18.0dB on 0.040s off 1.950s special dial tone: 380+420Hz -18.0dB continuous howler tone: 1400+2060+2450+2600Hz -3.0dB on 0.100s off 0.100s warning tone: 420Hz -18.0dB on 0.150s off 0.150s 420Hz -18.0dB on 0.150s off 1.950s...
Page 1004 Appendix A PSTN Parameters by Country Meter parameters: frequency: 12 kHz onTime: 200 ms offTime: 200 ms Caller ID parameters: CID type: prior ring payload type: ETSI-MDMF first TAS type: DT-AS second TAS type: NULL first TAS interval: 300 ms second TAS interval: 0 ms start to ring: 400 ms (prior ring only) Tones parameters:...
Page 1005 Appendix A PSTN Parameters by Country loop current: 25 mA tax type: metering Ring parameters: frequency: 20.0 Hz amplitude: 53.0 Vrms onTime1: 2.00 seconds offTime1: 4.00 seconds onTime2: 2.00 seconds offTime2: 4.00 seconds Pulse parameters: flashMin: 90 ms flashMax: 500 ms breakMin: 47 ms breakMax: 80 ms makeMin: 30 ms...
Page 1006 Appendix A PSTN Parameters by Country ring back tone: 425Hz -18.0dB on 1.000s off 4.000s busy tone: 425Hz -18.0dB on 0.500s off 0.500s congestion tone: 425Hz -18.0dB on 0.250s off 0.250s call waiting tone #1: 425Hz -18.0dB on 0.150s off 0.150s 425Hz -18.0dB on 0.150s off 4.000s call waiting tone #2: 2x(425Hz -18.0dB on 0.300s off 9.700s) special dial tone: 425Hz -18.0dB on 1.500s off 0.100s...

This manual is also suitable for:

Msc1224g series Msc1000g series

ZyXEL Communications MSC1024G Series User Manual

About this User's Guide

Document Conventions

Safety Warnings

Contents Overview

Table of Contents

Introduction

PART I Introduction

Chapter 1 Getting to Know Your MSC

Chapter 2 Hardware Connections

Web Configurator

Part II: Web Configurator

Chapter 3 The Web Configurator

Chapter 4 Tutorials

Chapter 5 Access Control List Screens

Chapter 6 Alarm Screens

Chapter 7 Cluster Screens

Chapter 8 Diagnostic Screens

Chapter 9 Maintenance Screens

Chapter 10 Multicast Screens

Chapter 11 Subscriber Port Setup Screens

Chapter 12 IMA Screens

Chapter 13 Profile Screens

Chapter 14 Statistics Screens

Quick Links

Troubleshooting

Related Manuals for ZyXEL Communications MSC1024G Series

Summary of Contents for ZyXEL Communications MSC1024G Series