Table of Contents
Advertisement
M-series and MX-series Devices
Related
Documentation
106
Table 48: FPC Configuration Details (continued)
Task
Enable shaping on an L2TP
session.
Configure the amount of
bandwidth for tunnel
services.
Configure Port-Mirroring
Instances.
Associate a sampling
instance.
Configuring Aggregated Devices (NSM Procedure) on page 99
Configuring Chassis Alarms (NSM Procedure) on page 100
Configuring a T640 Router on a Routing Matrix (NSM Procedure) on page 107
Your Action
1.
Click Add new entry next to Fpc.
2. Click Pic next to fpc.
3. Click Add new entry next to Pic.
4. Click Traffic Manager next to pic.
5. From the Ingress Shaping Overhead list, select the number of
CoS shaping overhead bytes to add to the packets on the
ingress side of the L2TP tunnel to determine the shaped session
packet length.
Range: 0 through 255
6. From the Egress Shaping Overhead list, select the number of
CoS shaping overhead bytes to add to the packets on the egress
interface.
Range: 0 through 255
7. From the Mode list, select the mode of shaping.
1.
Click Add new entry next to Fpc.
2. Click Pic next to fpc.
3. Click Add new entry next to Pic.
4. Click Tunnel Service next to pic.
5. From the Bandwidth list, select the bandwidth of 1 Gbps or
10Gbps on the Packet Forwarding Engine connected to a Gigabit
Ethernet 40-port DPC.
1.
Click Add new entry next to Fpc.
2. Click Port Mirror Instance next to fpc and perform the following:
Add—Adds the selected port-mirroring instances from the
Non member list to the Members list.
Remove—Removes the selected port-mirroring instances
from the Members list.
Add All—Adds all the port-mirroring instances from the
Non-members list to the Members list.
Remove All—Removes all the port-mirroring instances from
the Members list.
1.
Click Add new entry next to Fpc.
2. Click Sampling Instances next to fpc.
3. Click Add new entry next to Sampling Instances.
4. From the Name list, select the sampling instance name.
5. In the Comment box, enter the comment.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1