Suzuki SX4 Service Manual page 112
Hide thumbs
Also See for SX4:
- Owner's manual (47 pages) ,
- Owner's manual (16 pages) ,
- Owner's manual (278 pages)
Table of Contents
Advertisement
1A-62 Engine General Information and Diagnosis:
Step
1
Was "Engine and Emission Control System Check"
performed?
2
HO2S-2 heater power circuit check
1) Disconnect connector from HO2S-2 with ignition switch
turned OFF.
2) Check for proper connection to HO2S-2 at "BLK/WHT"
and "RED/BLU" wire terminals.
3) If wire and connection are OK, measure voltage
between "BLK/WHT" wire terminal of HO2S-2 connector
and engine ground with ignition switch turned ON.
Is voltage over 10 V?
3
HO2S-2 heater power circuit check
1) Disconnect connectors from ECM with ignition switch
turned OFF.
2) Measure resistance between "BLK/WHT" wire terminal
of HO2S-2 connector and "E01-29" terminal wire of ECM
connector.
Is resistance below 5
4
HO2S-2 heater drive circuit check
1) Measure resistance between "RED/BLU" wire terminal of
HO2S-2 connector and vehicle body ground.
Is resistance infinity?
5
HO2S-2 heater drive circuit check
1) Turn ON ignition switch.
2) Measure voltage between "RED/BLU" wire terminal of
HO2S-2 connector and vehicle body ground.
Is voltage 0 V?
6
HO2S-2 heater drive circuit check
1) Connect connector to HO2S-2 with ignition switch turned
OFF.
2) Turn ON ignition switch.
3) Measure voltage between "C01-47" terminal of
disconnected ECM connector and vehicle body ground.
Is voltage over 10 V?
7
HO2S-2 heater check
1) Disconnect HO2S-2 connector with ignition switch
turned OFF.
2) Check HO2S-2 heater resistance referring to "Heated
Oxygen Sensor (HO2S-1 and HO2S-2) Heater On-
Vehicle Inspection (If Equipped) in Section 1C".
Is resistance within specified value?
8
HO2S-2 heater power circuit check
1) Connect connector to HO2S-2 with ignition switch turned
OFF.
2) Measure resistance between "E01-29" and "C01-47"
terminals of ECM connector.
Is resistance below 30
Action
Ω
?
Ω
?
Yes
Go to Step 2.
Go to Step 3.
Go to Step 4.
Go to Step 5.
Go to Step 6.
Go to Step 7.
Go to Step 8.
HO2S-2 heater circuit is
OK. Substitute a known-
good ECM and recheck.
No
Go to "Engine and
Emission Control
System Check".
"BLK/WHT" wire is open
circuit or shorted to
ground circuit.
"BLK/WHT" wire is high
resistance circuit.
"RED/BLU" wire is
shorted to ground
circuit.
"RED/BLU" wire is
shorted to power circuit.
"RED/BLU" wire is open
circuit.
Replace HO2S-2.
"RED/BLU" wire is high
resistance circuit.
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated
My heater stopped working the blower **** is good, control unit ?
Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:
1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.
2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.
Checking and addressing these components should help identify and resolve the heater issue.
This answer is automatically generated