Suzuki SX4 Service Manual page 106
Hide thumbs
Also See for SX4:
- Owner's manual (47 pages) ,
- Owner's manual (18 pages) ,
- Owner's manual (16 pages)
Table of Contents
Advertisement
1A-56 Engine General Information and Diagnosis:
DTC Troubleshooting
NOTE
Before this troubleshooting is performed, read the precautions for DTC troubleshooting referring to
"Precautions for DTC Troubleshooting".
Step
1
Was "Engine and Emission Control System Check"
performed?
2
Oil control valve electrical circuit check
1) Disconnect connectors from ECM with ignition switch
turned OFF.
2) Check for proper connection at "C01-60" and "C01-59"
terminals of ECM connector.
3) If OK, measure resistance between "C01-60" and "C01-
59" terminals of ECM connector.
Is resistance below 10
3
Oil control valve electrical circuit check
Was resistance more than 6.5
4
Oil control valve electrical circuit for power short check
1) Turn ON ignition switch.
2) Measure voltage between "C01-60" terminal of ECM
connector and engine ground.
Is voltage below 1 V?
5
Oil control valve electrical circuit for ground short
check
1) Disconnect connector from oil control valve with ignition
switch turned OFF.
2) Measure resistance between "C01-60" terminal of ECM
connector and engine ground.
Is resistance infinity?
6
Oil control valve electrical circuit for ground short
check
1) Measure resistance between "C01-59" terminal of ECM
connector and engine ground.
Is resistance infinity?
7
Oil control valve electrical circuit for short check
1) Disconnect connector from oil control valve with ignition
switch turned OFF.
2) Measure resistance between "C01-60" and "C01-59"
terminals of ECM connector.
Is resistance infinity?
8
Oil control valve electrical circuit check
1) Disconnect connector from oil control valve with ignition
switch turned OFF.
2) Measure resistance between "C01-60" terminal of ECM
connector and "GRN/RED" wire terminal of oil control
valve connector and between "C01-59" terminal of ECM
connector and "GRN/WHT" wire terminal of oil control
valve connector.
Is resistance below 1
Action
Ω
?
Ω
in Step 2?
Ω
?
Yes
Go to Step 2.
Go to Step 3.
Go to Step 4.
Go to Step 5.
Go to Step 6.
Go to Step 7.
Go to Step 8.
Go to Step 9.
No
Go to "Engine and
Emission Control
System Check".
Go to Step 8.
Go to Step 7.
"RED", "GRN/RED",
"YEL" or "GRN/WHT"
wire is shorted to power
supply circuit.
"GRN/RED" wire is
shorted to ground
circuit.
"GRN/WHT" wire is
shorted to ground
circuit.
"GRN/RED" wire is
shorted to "GRN/WHT"
wire.
"GRN/RED" wire or
"GRN/WHT" wire circuit
is open or high
resistance.
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the SX4 and is the answer not in the manual?
Questions and answers
Adjust throttle motor
The idle speed on a Suzuki SX4 should be controlled by the Idle Air Control Valve (IACV) rather than adjusting the idle screw on the throttle body, as the screw is factory set. Before using compressed air in the idle-air-bypass passages, the IACV should be removed to prevent damage to its delicate mechanism. If there is an issue with idle speed, checking the IACV function and referring to the SX4 service manual is recommended.
This answer is automatically generated
I have an issue of crank but not starting When I scan it brought this codeU0100 Which means no communication thou crank sensor wire was cut off but it was fix back What could be wrong and what could be the solution,
increasing revs when changing gears
The Suzuki SX4 may have increasing revs when changing gears due to its drive-by-wire system and the difference in final drive ratios between the manual (4.41) and automatic (2.81) transmissions. This difference causes high cruising RPMs in the manual version and sluggishness in the automatic. Additionally, if the revs climb while going uphill, it may be due to the transmission downshifting or kicking out of overdrive. Other possible causes include low transmission fluid, abuse, or a faulty transmission design.
This answer is automatically generated
My heater stopped working the blower **** is good, control unit ?
Possible issues with the heater in a Suzuki SX4 if the blower is working but the heater is not include:
1. Incorrect Temperature Output
- Temperature control cable broken or bent (non-A/C and manual A/C) → Check the temperature control cable.
- Temperature selector faulty (non-A/C and manual A/C) → Check the temperature selector.
- Incorrect installation of the temperature control cable (non-A/C and manual A/C) → Check and adjust the position as necessary.
- Temperature control door assembly broken → Repair the temperature control door assembly.
- Air ducts clogged → Repair air ducts.
- Heater core leaked or clogged → Replace the heater core.
- Heater hoses leaked or clogged → Replace heater hoses.
- Thermostat faulty → Check the thermostat.
- Temperature control actuator faulty (auto A/C) → Check the temperature control actuator.
- HVAC control module faulty (auto A/C) → Check the HVAC control module.
- Wiring or grounding faulty (auto A/C) → Repair as necessary.
2. Other Possible Causes
- Air flow control cable broken or bent → Check the air flow control cable.
Checking and addressing these components should help identify and resolve the heater issue.
This answer is automatically generated