Siemens G130 List Manual page 662

2 Parameters
2.2 List of parameters
p4083[0...1] TM31 analog outputs offset / TM31 AO offset
TM31 Can be changed: U, T
Data type: FloatingPoint32
P-Group: Terminals
Not for motor type: -
Min
-20.000
Description: Sets the offset for the analog outputs of Terminal Module 31 (TM31).
The offset is added to the output signal after the scaling characteristic.
Index: [0] = AO 0 (X522.1, X522.2, X522.3)
[1] = AO 1 (X522.4, X522.5, X522.6)
Dependency: The unit of this parameter (V or mA) depends on the analog input type.
Refer to: r4076, p4076
Note: This means, for example, the offset of a downstream isolating amplifier can be compensated.
p4083[0...1] TB30 analog outputs offset / TB30 AO offset
TB30 Can be changed: U, T
Data type: FloatingPoint32
P-Group: Terminals
Not for motor type: -
Min
-10.000
Description: Sets the offset for the analog outputs of Terminal Board 30 (TB30).
The offset is added to the output signal after the scaling characteristic.
Index: [0] = AO 0 (X482.5/X482.6)
[1] = AO 1 (X482.7/X482.8)
p4095 TM31 digital inputs simulation mode / TM31 DI sim_mode
TM31 Can be changed: U, T
Data type: Unsigned32
P-Group: Terminals
Not for motor type: -
Min
-
Description: Sets the simulation mode for the digital inputs of Terminal Module 31 (TM31).
Bit field: Bit
00
01
02
03
04
05
06
07
08
09
10
11
Dependency: The setpoint for the input signals is specified using p4096.
Refer to: p4096
Warning: A drive that is moved by simulating the inputs of a Terminal Module is brought to a standstill while the Terminal
Module is being activated or deactivated.
662
Signal name
DI 0 (X520.1)
DI 1 (X520.2)
DI 2 (X520.3)
DI 3 (X520.4)
DI 4 (X530.1)
DI 5 (X530.2)
DI 6 (X530.3)
DI 7 (X530.4)
DI/DO 8 (X541.2)
DI/DO 9 (X541.3)
DI/DO 10 (X541.4)
DI/DO 11 (X541.5)
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
20.000
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
10.000
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
1 signal
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
List Manual (LH2), 07/2016, A5E03263479A
Access level: 1
Func. diagram: 9572
Unit selection: -
Expert list: 1
Factory setting
0.000
Access level: 1
Func. diagram: 9106
Unit selection: -
Expert list: 1
Factory setting
0.000
Access level: 2
Func. diagram: 9549, 9550,
9552, 9560, 9562
Unit selection: -
Expert list: 1
Factory setting
0000 0000 0000 0000 bin
0 signal
Terminal eval
Terminal eval
Terminal eval
Terminal eval
Terminal eval
Terminal eval
Terminal eval
Terminal eval
Terminal eval
Terminal eval
Terminal eval
Terminal eval
SINAMICS G130/G150
FP
-
-
-
-
-
-
-
-
-
-
-
-