Siemens G130 List Manual page 1076

2 Parameters
2.3 Parameters for data sets
p1754[0...n]
p1755[0...n]
p1757[0...n]
p1758[0...n]
p1759[0...n]
p1760[0...n]
p1761[0...n]
p1764[0...n]
p1766[0...n]
p1767[0...n]
p1774[0...n]
p1775[0...n]
p1780[0...n]
p1784[0...n]
p1785[0...n]
p1786[0...n]
r1787[0...n]
p1795[0...n]
r1797[0...n]
p1798[0...n]
p1800[0...n]
p1802[0...n]
p1803[0...n]
p1804[0...n]
p1806[0...n]
p1811[0...n]
p1814[0...n]
p1820[0...n]
p1821[0...n]
p1840[0...n]
p1845[0...n]
p1846[0...n]
p1959[0...n]
p1998[0...n]
p2140[0...n]
p2141[0...n]
p2142[0...n]
p2149[0...n]
p2150[0...n]
p2153[0...n]
p2155[0...n]
p2156[0...n]
p2161[0...n]
p2162[0...n]
p2163[0...n]
p2164[0...n]
p2166[0...n]
p2167[0...n]
p2174[0...n]
p2175[0...n]
p2177[0...n]
p2178[0...n]
p2181[0...n]
p2182[0...n]
p2183[0...n]
1076
Flux angle difference smoothing time / Angle diff T_smth
Motor model changeover speed encoderless operation / MotMod n_chgSnsorl
Motor model w/o enc. op./cl.-loop controlled stab. controller Kp / MotMod w/o enc Kp
Motor model changeover delay time closed/open-loop control / MotMod t cl_op
Motor model changeover delay time open/closed-loop control / MotMod t op_cl
Motor model with encoder speed adaptation Kp / MotMod wE n_ada Kp
Motor model with encoder speed adaptation Tn / MotMod wE n_ada Tn
Motor model without encoder speed adaptation Kp / MotMod woE n_adaKp
Motor model voltage model calculation enable / U_mod calc enab
Motor model without encoder speed adaptation Tn / MotMod woE n_adaTn
Motor model offset voltage compensation alpha / MotMod offs comp A
Motor model offset voltage compensation beta / MotMod offs comp B
Motor model adaptation configuration / MotMod adapt conf
Motor model feedback scaling / MotMod fdbk scal
Motor model Lh adaptation Kp / MotMod Lh Kp
Motor model Lh adaptation integral time / MotMod Lh Tn
Motor model Lh adaptation corrective value / MotMod Lh corr
Motor model kT adaptation integral time / MotMod kT Tn
Motor model kT adaptation corrective value / MotMod kT corr
Motor model pulse technique speed adaptation Kp / MotMod PulsTech Kp
Pulse frequency setpoint / Pulse freq setp
Modulator mode / Modulator mode
Maximum modulation depth / Modulat depth max
Filter time constant smoothed modulation index / T_filt mod_idx sm
Filter time constant Vdc correction / T_filt Vdc_corr
Pulse frequency wobbulation amplitude / Puls wobb ampl
Vdc filter dead band for modulation switchover / Vdc filt dead band
Reverse the output phase sequence / Outp_ph_seq rev
Dir of rot / Dir of rot
Actual value correction configuration / ActVal_corr conf
Actual value correction evaluation factor Lsig / ActVal_cor ev Lsig
Actual value correction damping factor / ActV_corr D_factor
Rotating measurement configuration / Rot meas config
PolID circle center point / PolID circ center
Hysteresis speed 2 / n_hysteresis 2
Speed threshold 1 / n_thresh val 1
Hysteresis speed 1 / n_hysteresis 1
Monitoring configuration / Monit config
Hysteresis speed 3 / n_hysteresis 3
Speed actual value filter time constant / n_act_filt T
Speed threshold 2 / n_thresh val 2
On delay comparison value reached / t_on cmpr val rchd
Speed threshold 3 / n_thresh val 3
Hysteresis speed n_act > n_max / Hyst n_act>n_max
Speed threshold 4 / n_thresh val 4
Hysteresis speed 4 / n_hysteresis 4
Off delay n_act = n_set / t_del_off n_i=n_so
Switch-on delay n_act = n_set / t_on n_act=n_set
Torque threshold value 1 / M_thresh val 1
Motor blocked speed threshold / Mot lock n_thresh
Motor blocked delay time / Mot lock t_del
Motor stalled delay time / Mot stall t_del
Load monitoring response / Load monit resp
Load monitoring speed threshold value 1 / n_thresh 1
Load monitoring speed threshold value 2 / n_thresh 2
SINAMICS G130/G150
List Manual (LH2), 07/2016, A5E03263479A