Siemens G130 List Manual page 551

Note: The binector input is automatically pre-assigned to r1199.2.
The following applies for SERVO:
The pre-assignment using the automatic calculation of the motor/control parameters in the drive (p0340 = 1, 3, 5) is
only realized if, at the instant of the calculation, the "setpoint channel" function module is active (r0108.8 = 1). If the
calculation in p0340 is not selected when downloading parameters, then the parameter is not pre-assigned.
p2149[0...n] Monitoring configuration / Monit config
VECTOR_G Can be changed: U, T
Data type: Unsigned16
P-Group: Messages
Not for motor type: -
Min
-
Description: Sets the configuration for messages and monitoring functions.
Bit field: Bit
00
01
03
06
15
Dependency: Refer to: r2197
Refer to: A07903
Note: For bit 00:
Alarm A07903 is output when the bit is set with r2197.7 = 0 (n_set <> n_act).
For bit 01:
As a result of the positive characteristic parameters (p2182 ... p2190), when the bit is set, the load monitoring is only
executed in the 1st quadrants.
For bit 03:
When the bit is set, r2197.1 and r2197.2 are determined using separate hysteresis functions.
For bit 06:
When the bit is set, with r2197.1 = 1 (n_act < p2155 speed threshold value 2) alarm A08721 is output, and with
r2199.0 = 1 (n_act < p2161 speed threshold value 3), fault F07822 is output.
For separately excited synchronous motors (without encoder) in torque control (p1501 set), the underspeed speed
monitoring is automatically activated if conditions (p0300 = 5, p1300 = 20) for the automatic pre-assignment of the
threshold values during commissioning (p0340 = 1) are fulfilled.
The alarm threshold p2155 is preassigned with 1.5 * p1755 - and the fault threshold p2161, with p1755.
For bit 15:
The bit indicates whether the automatic parameterization (p0340 = 1, p3900 > 0) for the parameters of the extended
monitoring functions was carried out.
If the bit is not set (e.g. when the configuration is activated (p0108.15)), the parameterization is automatically carried
out during booting even if r3925.0 is already 1.
p2150[0...n] Hysteresis speed 3 / n_hysteresis 3
VECTOR_G Can be changed: U, T
Data type: FloatingPoint32
P-Group: Messages
Not for motor type: -
Min
0.00 [rpm]
Description: Sets the hysteresis speed (bandwidth) for the following signals:
"|n_act| < speed threshold value 3" (BO: r2199.0)
"n_set >= 0" (BO: r2198.5)
"n_act >= 0" (BO: r2197.3)
Dependency: Refer to: p2161, r2197, r2199
SINAMICS G130/G150
List Manual (LH2), 07/2016, A5E03263479A
Signal name
Enable alarm A07903
Load monitoring only in the 1st quadrant
Reserved
Enable underspeed monitoring
Automatic parameterization carried out
(p0340 = 1, p3900 > 0)
Calculated: -
Dyn. index: DDS, p0180
Unit group: -
Scaling: -
Max
-
1 signal
Yes
Yes
Yes
Yes
Calculated:
CALC_MOD_LIM_REF
Dyn. index: DDS, p0180
Unit group: 3_1
Scaling: -
Max
300.00 [rpm]
2 Parameters
2.2 List of parameters
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 0000 0000 0001 bin
0 signal
No
No
No
No
Access level: 3
Func. diagram: 8010, 8011
Unit selection: p0505
Expert list: 1
Factory setting
2.00 [rpm]
FP
8011
8013
-
8010
-
551