Siemens G130 List Manual page 394

2 Parameters
2.2 List of parameters
r1454 CO: Speed controller system deviation I component / n_ctrl sys dev Tn
VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
- [rpm]
Description: Display and connector output for the system deviation of the I component of the speed controller.
When the reference model is inactive (p1433 = 0 Hz), this parameter corresponds to the system deviation of the
complete PI controller (r1454 = r0064).
p1455[0...n] CI: Speed controller P gain adaptation signal / n_ctr adapt_sig Kp
VECTOR_G (n/M) Can be changed: T
Data type: Unsigned32 / FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
-
Description: Sets the source for the adaptation signal to additionally adapt the P gain of the speed controller.
Dependency: Refer to: p1456, p1457, p1458, p1459
p1456[0...n] Speed controller P gain adaptation lower starting point / n_ctrl AdaptKpLow
VECTOR_G (n/M) Can be changed: U, T
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
0.00 [%]
Description: Sets the lower starting point of the adaptation range for the additional adaptation of the P gain of the speed controller.
The values are in % and refer to the set source of the adaptation signal.
Dependency: Refer to: p1455, p1457, p1458, p1459
Note: If the upper transition point p1457 of the speed controller adaptation is set to lower values than the lower transition
p1456, then the controller gain below p1457 is adapted with p1459 and above p1456, with p1458.
p1457[0...n] Speed controller P gain adaptation upper starting point / n_ctrl AdaptKp up
VECTOR_G (n/M) Can be changed: U, T
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
0.00 [%]
Description: Sets the upper starting point of the adaptation range for the additional adaptation of the P gain of the speed
controller.
The values are in % and refer to the set source of the adaptation signal.
Dependency: Refer to: p1455, p1456, p1458, p1459
Note: If the upper transition point p1457 of the speed controller adaptation is set to lower values than the lower transition
p1456, then the controller gain below p1457 is adapted with p1459 and above p1456, with p1458.
394
Calculated: -
Dyn. index: -
Unit group: 3_1
Scaling: p2000
Max
- [rpm]
Calculated: -
Dyn. index: CDS, p0170
Unit group: -
Scaling: PERCENT
Max
-
Calculated: -
Dyn. index: DDS, p0180
Unit group: -
Scaling: -
Max
400.00 [%]
Calculated: -
Dyn. index: DDS, p0180
Unit group: -
Scaling: -
Max
400.00 [%]
List Manual (LH2), 07/2016, A5E03263479A
Access level: 3
Func. diagram: 6040
Unit selection: p0505
Expert list: 1
Factory setting
- [rpm]
Access level: 3
Func. diagram: 6050
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 6050
Unit selection: -
Expert list: 1
Factory setting
0.00 [%]
Access level: 3
Func. diagram: 6050
Unit selection: -
Expert list: 1
Factory setting
0.00 [%]
SINAMICS G130/G150