Siemens G130 List Manual page 1075

p1605[0...n]
p1607[0...n]
p1609[0...n]
p1610[0...n]
p1611[0...n]
p1612[0...n]
p1616[0...n]
p1619[0...n]
p1620[0...n]
p1621[0...n]
p1622[0...n]
p1625[0...n]
p1628[0...n]
p1629[0...n]
p1630[0...n]
p1642[0...n]
p1643[0...n]
p1653[0...n]
p1654[0...n]
p1656[0...n]
p1657[0...n]
p1658[0...n]
p1659[0...n]
p1660[0...n]
p1661[0...n]
p1662[0...n]
p1663[0...n]
p1664[0...n]
p1665[0...n]
p1666[0...n]
p1677[0...n]
p1678[0...n]
p1679[0...n]
p1680[0...n]
p1681[0...n]
p1702[0...n]
p1703[0...n]
p1704[0...n]
p1705[0...n]
p1715[0...n]
p1717[0...n]
p1720[0...n]
p1722[0...n]
p1726[0...n]
p1727[0...n]
p1730[0...n]
p1731[0...n]
p1740[0...n]
p1744[0...n]
p1745[0...n]
p1748[0...n]
p1749[0...n]
p1750[0...n]
p1752[0...n]
p1753[0...n]
SINAMICS G130/G150
List Manual (LH2), 07/2016, A5E03263479A
Pulse technique pattern configuration / Puls pattrn config
Pulse technique stimulus / Puls stimulus
I/f operation current setpoint / I/f op I_setp
Torque setpoint static (sensorless) / M_set static
Additional acceleration torque (sensorless) / M_suppl_accel
Current setpoint magnetizing open-loop controlled / Id_set ctrl
Current setpoint smoothing time / I_set T_smooth
Setpoint/actual value tracking threshold / SetAct track thrsh
Stator current minimum / I_stator min
Changeover speed inner cos phi = 1 / n_chngov cos phi=1
Field-generating current setpoint smoothing time constant / Id_setp T_smth
Excitation current setpoint calibration / I_exc_setp cal
Current model controller dynamic factor / I_mod_ctr dyn_fact
Current model controller P gain / I_mod_ctrl Kp
Current model controller integral time / I_mod_ctrl Tn
Minimum excitation current / Min I_exc
Minimum excitation current closed-loop control gain factor / I_exc_min Kp
Current setpoint torque-generating smoothing time minimum / Isq_s T_smth min
Curr. setpoint torque-gen. smoothing time field weakening range / Isq_s T_smth FW
Current setpoint/Speed actual value filter activation / I_setp_filt act
Current setpoint filter 1 type / I_set_filt 1 type
Current setpoint filter 1 denominator natural frequency / I_set_filt1 fn_den
Current setpoint filter 1 denominator damping / I_set_filt 1 D_den
Current setpoint filter 1 numerator natural frequency / I_set_filt1 fn_num
Current setpoint filter 1 numerator damping / I_set_filt 1 D_num
Current setpoint filter 2 type / I_set_filt 2 type
Current setpoint filter 2 denominator natural frequency / I_set_filt2 fn_den
Current setpoint filter 2 denominator damping / I_set_filt 2 D_den
Current setpoint filter 2 numerator natural frequency / I_set_filt2 fn_num
Current setpoint filter 2 numerator damping / I_set_filt 2 D_num
Speed actual value filter 5 type / n_act_filt 5 type
Speed actual value filter 5 denominator natural frequency / n_act_filt5 fn_den
Speed actual value filter 5 denominator damping / n_act_filt 5 D_den
Speed actual value filter 5 numerator natural frequency / n_act_filt5 fn_num
Speed actual value filter 5 numerator damping / n_act_filt 5 D_num
Isd current controller pre-control scaling / Isd_ctr_prectrScal
Isq current controller pre-control scaling / Isq_ctr_prectrScal
Isq current controller pre-control EMF scaling / Isq_ctrl EMF scal
Flux setpoint/actual value tracking threshold / Flux track thresh
Current controller P gain / I_ctrl Kp
Current controller integral-action time / I_ctrl Tn
Current controller d axis p gain / Id_ctrl Kp
Current controller d axis integral time / I_ctrl d-axis Tn
Quadrature arm decoupling scaling / Transv_decpl scal
Quadrature arm decoupling at voltage limit scaling / TrnsvDecplVmaxScal
Isd controller integral component shutdown threshold / Isd ctrl Tn shutd
Isd controller combination current time component / Isd ctr I_combi T1
Gain resonance damping for encoderless closed-loop control / Gain res_damp
Motor model speed threshold stall detection / MotMod n_thr stall
Motor model error threshold stall detection / MotMod ThreshStall
Motor model lower changeover speed n_set -> n_act / MotMod low n_chng
Motor model upper changeover speed / increase changeover speed / Up/incr n_chngov
Motor model configuration / MotMod config
Motor model changeover speed operation with encoder / MotMod n_chgov enc
Motor model changeover speed hysteresis operation with encoder / MotMod n_chgovHysE
2 Parameters
2.3 Parameters for data sets
1075