Siemens G130 List Manual page 458

2 Parameters
2.2 List of parameters
r1791 Motor model Lh adaptation switch-on frequency / MotMod Lh f_on
VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: PMSM, SESM, REL
Min
- [Hz]
Description: Displays the switch-on stator frequency/ primary section frequency for the Lh adaptation for the induction motor
(ASM).
r1792 Motor model Lh adaptation switch-on slip / MotMod Lh fslip
VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: PMSM, SESM, REL
Min
- [Hz]
Description: Displays the switch-on slip frequency for the Lh adaptation for the induction motor (ASM).
p1795[0...n] Motor model kT adaptation integral time / MotMod kT Tn
VECTOR_G (n/M) Can be changed: U, T
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: ASM, SESM, REL
Min
10 [ms]
Description: Sets the integral time of the kT adaptation of the motor model for a permanent-magnet synchronous motor (PMSM).
r1797[0...n] Motor model kT adaptation corrective value / MotMod kT corr
VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: ASM, SESM, REL
Min
- [Nm/A]
Description: Displays the corrective value of the kT adaptation of the motor model for a permanent-magnet synchronous motor
(PMSM).
Dependency: Refer to: p0826, p1780
Note: The display of the inactive data sets is only updated when changing over the data set.
p1798[0...n] Motor model pulse technique speed adaptation Kp / MotMod PulsTech Kp
VECTOR_G (n/M) Can be changed: U, T
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: ASM, SESM, REL
Min
0.000
Description: Sets the proportional gain Kp for speed adaptation with active pulse technique for the estimation of the continuous
rotor position.
458
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
- [Hz]
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
- [Hz]
Calculated: CALC_MOD_CON
Dyn. index: DDS, p0180
Unit group: -
Scaling: -
Max
10000 [ms]
Calculated: -
Dyn. index: DDS, p0180
Unit group: -
Scaling: -
Max
- [Nm/A]
Calculated: CALC_MOD_CON
Dyn. index: DDS, p0180
Unit group: -
Scaling: -
Max
1000.000
List Manual (LH2), 07/2016, A5E03263479A
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
- [Hz]
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
- [Hz]
Access level: 3
Func. diagram: 6731
Unit selection: -
Expert list: 1
Factory setting
100 [ms]
Access level: 3
Func. diagram: 6731
Unit selection: -
Expert list: 1
Factory setting
- [Nm/A]
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
1.000
SINAMICS G130/G150