Siemens G130 List Manual page 1073

p1288[0...n]
p1289[0...n]
p1290[0...n]
p1291[0...n]
p1292[0...n]
p1293[0...n]
p1295[0...n]
p1296[0...n]
p1297[0...n]
p1300[0...n]
p1302[0...n]
p1310[0...n]
p1311[0...n]
p1312[0...n]
p1320[0...n]
p1321[0...n]
p1322[0...n]
p1323[0...n]
p1324[0...n]
p1325[0...n]
p1326[0...n]
p1327[0...n]
p1331[0...n]
p1333[0...n]
p1334[0...n]
p1335[0...n]
p1336[0...n]
p1338[0...n]
p1339[0...n]
p1340[0...n]
p1341[0...n]
p1345[0...n]
p1346[0...n]
p1349[0...n]
p1350[0...n]
p1351[0...n]
p1358[0...n]
p1381[0...n]
p1400[0...n]
p1401[0...n]
p1402[0...n]
p1416[0...n]
p1428[0...n]
p1429[0...n]
p1433[0...n]
p1434[0...n]
p1435[0...n]
p1441[0...n]
p1442[0...n]
p1451[0...n]
p1452[0...n]
p1456[0...n]
p1457[0...n]
p1458[0...n]
p1459[0...n]
SINAMICS G130/G150
List Manual (LH2), 07/2016, A5E03263479A
Vdc_max controller feedback coupling factor ramp-fct. gen. (U/f) / Vdc_max factor RFG
Vdc_max controller speed threshold (U/f) / Vdc_max n_thresh
Vdc controller proportional gain (U/f) / Vdc_ctrl Kp
Vdc controller integral time (U/f) / Vdc_ctrl Tn
Vdc controller rate time (U/f) / Vdc_ctrl t_rate
Vdc min controller output limit (U/f) / Vdc_min outp_lim
Vdc_min controller time threshold (U/f) / Vdc_min t_thresh
Vdc_min controller response (kinetic buffering) (U/f / Vdc_min response
Vdc_min controller speed threshold (U/f) / Vdc_min n_thresh
Open-loop/closed-loop control operating mode / Op/cl-lp ctrl_mode
U/f control configuration / U/f config
Starting current (voltage boost) permanent / I_start (Ua) perm
Starting current (voltage boost) when accelerating / I_start accel
Starting current (voltage boost) when starting / I_start start
U/f control programmable characteristic frequency 1 / Uf char f1
U/f control programmable characteristic voltage 1 / Uf char U1
U/f control programmable characteristic frequency 2 / Uf char f2
U/f control programmable characteristic voltage 2 / Uf char U2
U/f control programmable characteristic frequency 3 / Uf char f3
U/f control programmable characteristic voltage 3 / Uf char U3
U/f control programmable characteristic frequency 4 / Uf char f4
U/f control programmable characteristic voltage 4 / Uf char U4
Voltage limiting / U_lim
U/f control FCC starting frequency / U/f FCC f_start
U/f control slip compensation starting frequency / Slip comp start
Slip compensation scaling / Slip comp scal
Slip compensation limit value / Slip comp lim val
U/f mode resonance damping gain / Uf Res_damp gain
U/f mode resonance damping filter time constant / Uf Res_damp T
I_max frequency controller proportional gain / I_max_ctrl Kp
I_max frequency controller integral time / I_max_ctrl Tn
I_max voltage controller proportional gain / I_max_U_ctrl Kp
I_max voltage controller integral time / I_max_U_ctrl Tn
U/f mode resonance damping maximum frequency / Uf res_damp f_max
U/f control soft start / U/f soft start
CO: Motor holding brake starting frequency / Brake f_start
Angular difference symmetrizing actual angle / Sym act angle
U/f control modulation limit reduction / U/f mod_max reduc
Speed control configuration / n_ctrl config
Flux control configuration / Flux ctrl config
Closed-loop current control and motor model configuration / I_ctrl config
Speed setpoint filter 1 time constant / n_set_filt 1 T
Speed pre-control balancing dead time / n_prectrBal t_dead
Speed pre-control balancing time constant / n_prectr bal T
Speed controller reference model natural frequency / n_ctrl RefMod fn
Speed controller reference model damping / n_ctrl RefMod D
Speed controller reference model dead time / n_ctrRefMod t_dead
Actual speed smoothing time / n_act T_smooth
Speed controller speed actual value smoothing time / n_ctr n_act T_smth
Motor model speed actual value smoothing time sensorless / Mot_mod n_act t_sm
Speed controller speed actual value smoothing time (sensorless) / n_C n_act T_s SL
Speed controller P gain adaptation lower starting point / n_ctrl AdaptKpLow
Speed controller P gain adaptation upper starting point / n_ctrl AdaptKp up
Adaptation factor lower / Adapt_factor lower
Adaptation factor upper / Adapt_factor upper
2 Parameters
2.3 Parameters for data sets
1073