Siemens G130 List Manual page 181

Note: For encoders with serial number, encoder replacement is monitored in order to request angular commutation
calibration (adjustment) for motor encoders and absolute calibration for direct measuring systems with absolute value
data. The serial number, which from then onwards is used for monitoring purposes, can be transferred using p0440.
In the following cases, copying is automatically started in the following cases:
1.) When commissioning 1FT6, 1FK6, 1FK7 motors.
2.) When writing into p0431.
3.) For p1990 = 1.
p0440 is automatically set to 0 when the copying has been completed.
In order to permanently accept the copied values, it is necessary to save in a non-volatile fashion (p0977).
p0441[0...n] Encoder commissioning serial number part 1 / Enc comm ser_no 1
VECTOR_G, ENC Can be changed: C2(4)
Data type: Unsigned32
P-Group: Encoder
Not for motor type: -
Min
0000 hex
Description: Serial number part 1 of the encoder for the commissioning.
Dependency: Refer to: p0440, p0442, p0443, p0444, p0445, r0460, r0461, r0462, r0463, r0464
Note: A value of zero is displayed if an encoder is not present.
p0442[0...n] Encoder commissioning serial number part 2 / Enc comm ser_no 2
VECTOR_G, ENC Can be changed: C2(4)
Data type: Unsigned32
P-Group: Encoder
Not for motor type: -
Min
0000 hex
Description: Serial number part 2 of the encoder for the commissioning.
Dependency: Refer to: p0440, p0441, p0443, p0444, p0445, r0460, r0461, r0462, r0463, r0464
Note: A value of zero is displayed if an encoder is not present.
p0443[0...n] Encoder commissioning serial number part 3 / Enc comm ser_no 3
VECTOR_G, ENC Can be changed: C2(4)
Data type: Unsigned32
P-Group: Encoder
Not for motor type: -
Min
0000 hex
Description: Serial number part 3 of the encoder for the commissioning.
Dependency: Refer to: p0440, p0441, p0442, p0444, p0445, r0460, r0461, r0462, r0463, r0464
Note: A value of zero is displayed if an encoder is not present.
p0444[0...n] Encoder commissioning serial number part 4 / Enc comm ser_no 4
VECTOR_G, ENC Can be changed: C2(4)
Data type: Unsigned32
P-Group: Encoder
Not for motor type: -
Min
0000 hex
Description: Serial number part 4 of the encoder for the commissioning.
Dependency: Refer to: p0440, p0441, p0442, p0443, p0445, r0460, r0461, r0462, r0463, r0464
Note: A value of zero is displayed if an encoder is not present.
SINAMICS G130/G150
List Manual (LH2), 07/2016, A5E03263479A
Calculated: CALC_MOD_ALL
Dyn. index: EDS, p0140
Unit group: -
Scaling: -
Max
FFFF FFFF hex
Calculated: CALC_MOD_ALL
Dyn. index: EDS, p0140
Unit group: -
Scaling: -
Max
FFFF FFFF hex
Calculated: CALC_MOD_ALL
Dyn. index: EDS, p0140
Unit group: -
Scaling: -
Max
FFFF FFFF hex
Calculated: CALC_MOD_ALL
Dyn. index: EDS, p0140
Unit group: -
Scaling: -
Max
FFFF FFFF hex
2 Parameters
2.2 List of parameters
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 hex
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 hex
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 hex
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0000 hex
181