Siemens G130 List Manual page 262

2 Parameters
2.2 List of parameters
p0779[0...2] Test socket characteristic value x2 / Test skt char x2
CU_G130_PN, Can be changed: U, T
CU_G150_PN,
Data type: FloatingPoint32
CU_G130_DP,
P-Group: Terminals
CU_G150_DP
Not for motor type: -
Min
-100000.00 [%]
Description: The scaling characteristic for the test sockets is defined using two points.
This parameter specifies the x coordinate (percentage) of the second point on the characteristic.
Index: [0] = T0
[1] = T1
[2] = T2
Dependency: Can only be set when p0776 = 99.
Refer to: p0777, p0778, p0780, r0786
Note: The value 100.00 % corresponds to 4.98 V.
p0780[0...2] Test socket characteristic value y2 / Test skt char y2
CU_G130_PN, Can be changed: U, T
CU_G150_PN,
Data type: FloatingPoint32
CU_G130_DP,
P-Group: Terminals
CU_G150_DP
Not for motor type: -
Min
0.00 [V]
Description: The scaling characteristic for the test sockets is defined using two points.
This parameter specifies the y coordinate (output voltage) of the second point on the characteristic.
Index: [0] = T0
[1] = T1
[2] = T2
Dependency: Can only be set when p0776 = 99.
Refer to: p0777, p0778, p0779, r0786
p0783[0...2] Test sockets offset / Test skt offset
CU_G130_PN, Can be changed: U, T
CU_G150_PN,
Data type: FloatingPoint32
CU_G130_DP,
P-Group: Terminals
CU_G150_DP
Not for motor type: -
Min
-4.98 [V]
Description: Sets an additional offset for the test sockets.
Index: [0] = T0
[1] = T1
[2] = T2
p0784[0...2] Test socket limit on/off / TestSktLim on/off
CU_G130_PN, Can be changed: U, T
CU_G150_PN,
Data type: Integer16
CU_G130_DP,
P-Group: Terminals
CU_G150_DP
Not for motor type: -
Min
0
Description: Sets the limit for a signal to be output via test sockets.
Value: 0:
1:
262
Limiting off
Limiting on
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
427.9E9 [%]
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
4.98 [V]
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
4.98 [V]
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
1
List Manual (LH2), 07/2016, A5E03263479A
Access level: 2
Func. diagram: 8134
Unit selection: -
Expert list: 1
Factory setting
100.00 [%]
Access level: 2
Func. diagram: 8134
Unit selection: -
Expert list: 1
Factory setting
4.98 [V]
Access level: 2
Func. diagram: 8134
Unit selection: -
Expert list: 1
Factory setting
0.00 [V]
Access level: 2
Func. diagram: 8134
Unit selection: -
Expert list: 1
Factory setting
0
SINAMICS G130/G150