Subaru IMPREZA GD 2007 Series Manual page 2827

asieps_tobira_IM_US.book 4 ページ ２０１２年１月１７日 火曜日 午後３時４８分
MANUAL TRANSMISSION AND DIFFERENTIAL
8. EXTENSION ASSEMBLY
Taper roller bearing preload
(standard protrusion) :
0.15 — 0.20 mm (0.006 — 0.008 in)
NOTE:
Always adjust to the specified range of preload.
Thrust washer (50 × 61 × t)
Part No.
803050060
803050061
803050062
803050063
803050064
803050065
803050066
803050067
803050068
803050069
803050070
803050071
803050072
803050073
803050074
803050075
803050076
803050077
803050078
803050079
Thrust washer to center differential side
clearance:
0.15 — 0.35 mm (0.0059 — 0.0138 in)
Thrust washer
Part No.
803036050
803036054
803036051
803036055
803036052
803036056
803036053
803036057
803036058
General Description
9. FRONT DIFFERENTIAL
Bevel gear to pinion backlash:
803038021
Thickness mm (in)
0.50 (0.0197)
0.55 (0.0217)
0.60 (0.0236)
803038022
0.65 (0.0256)
0.70 (0.0276)
0.75 (0.0295)
Pinion shaft to axle drive shaft clearance:
0.80 (0.0315)
0.85 (0.0335)
0.90 (0.0354)
0.95 (0.0374)
1.00 (0.0394)
805028011
1.05 (0.0413)
10.TRANSFER DRIVE GEAR
1.10 (0.0433)
1.15 (0.0453)
Snap ring (Outer-30) to ball bearing clearance:
1.20 (0.0472)
1.25 (0.0492)
1.30 (0.0512)
1.35 (0.0531)
1.40 (0.0551)
1.45 (0.0571)
Thickness mm (in)
0.9 (0.035)
1.0 (0.039)
1.1 (0.043)
1.2 (0.047)
1.3 (0.051)
1.4 (0.055)
1.5 (0.059)
1.6 (0.063)
1.7 (0.067)
5MT-4
0.13 — 0.18 mm (0.0051 — 0.0071 in)
Washer (38.1 × 50 × t)
Thickness
Part No. Part No.
mm (in)
0.925 —
0.950
803038023
(0.0364 —
0.0374)
0.975 —
1.000
(0.0384 —
0.0394)
0 — 0.2 mm (0 — 0.008 in)
Snap ring (Outer-28)
Thickness
Part No. Part No.
mm (in)
1.05 (0.0413) 805028012
0.01 — 0.15 mm (0.0004 — 0.0059 in)
Snap ring (Outer-30)
Part No.
805030041
805030042
805030043
Thickness
mm (in)
1.025 —
1.050
(0.0404 —
0.0413)
— —
Thickness
mm (in)
1.20 (0.0472)
Thickness mm (in)
1.53 (0.0602)
1.65 (0.0650)
1.77 (0.0697)