Subaru IMPREZA GD 2007 Series Manual page 2666

asieps_tobira_IM_US.book 27 ページ ２０１２年１月１７日 火曜日 午後３時４８分
Diagnostic Procedure for Subaru Select Monitor Communication
Step
1 CHECK SUBARU SELECT MONITOR POW-
ER SUPPLY CIRCUIT.
Measure the voltage between data link connec-
tor and chassis ground.
Connector & terminal
(B40) No. 16 (+) — Chassis ground (–):
2 CHECK SUBARU SELECT MONITOR
GROUND CIRCUIT.
Measure the resistance of harness between
data link connector and chassis ground.
Connector & terminal
(B40) No. 4 — Chassis ground:
(B40) No. 5 — Chassis ground:
3 CHECK COMMUNICATION OF SUBARU SE-
LECT MONITOR.
1) Turn the ignition switch to ON.
2) Using the Subaru Select Monitor, check
whether communication to the transmission
system can be executed normally.
4 CHECK COMMUNICATION OF SUBARU SE-
LECT MONITOR.
1) Turn the ignition switch to OFF.
2) Disconnect the TCM connector.
3) Turn the ignition switch to ON and run the
Subaru Select Monitor.
4) Check whether communication to engine
system can be executed normally.
5 CHECK COMMUNICATION OF SUBARU SE-
LECT MONITOR.
1) Turn the ignition switch to OFF.
2) Connect the TCM connector.
3) Check whether communication to transmis-
sion system can be executed normally.
6 CHECK HARNESS CONNECTOR BETWEEN
EACH CONTROL MODULE AND DATA LINK
CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the TCM and ECM connector.
3) Measure the resistance between TCM con-
nector and chassis ground.
Connector & terminal
(B40) No. 7 — Chassis ground:
7 CHECK OUTPUT SIGNAL OF TCM.
1) Turn the ignition switch to ON.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B40) No. 7 (+) — Chassis ground (–):
8 CHECK HARNESS CONNECTOR BETWEEN
TCM AND DATA LINK CONNECTOR.
Measure the resistance between TCM connec-
tor and data link connector.
Connector & terminal
(B54) No. 8 — (B40) No. 7:
9 CHECK INSTALLATION OF TCM CONNEC-
TOR.
Turn the ignition switch to OFF.
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
Check
Is the voltage 10 V or more?
Is the resistance less than 1 Ω? Go to step 3.
Is the name of system dis-
played on Subaru Select Moni-
tor?
Is the name of system dis-
played on Subaru Select Moni-
tor?
Is the name of system dis-
played on Subaru Select Moni-
tor?
Is the resistance 1 MΩ or
more?
Is the voltage 1 V or more?
Is the resistance less than 0.5
Ω?
Is TCM connector connected to
TCM?
4AT(D)(diag)-27
Yes No
Go to step 2. Repair harnesses
and connectors
between the bat-
tery and data link
connector, and
poor contact of the
connector.
Repair the open
circuit of harness
between data link
connector and
ground terminal,
and poor contact of
connector.
Go to step 8. Go to step 4.
Go to step 6. Go to step 5.
Inspect the ECM. Go to step 6.
Go to step 7.
Check harness
and connector
between each con-
trol module and
data link connec-
tor.
Check harness Go to step 8.
and connector
between each con-
trol module and
data link connec-
tor.
Go to step 9. Repair the harness
and connector
between TCM and
data link connec-
tor.
Go to step 10.
Connect the TCM
connector to TCM.