Subaru IMPREZA GD 2007 Series Manual page 2655

asieps_tobira_IM_US.book 16 ページ ２０１２年１月１７日 火曜日 午後３時４８分
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
3. CLEAR MEMORY MODE
1) On the «Main Menu» display screen, select {Each
System Check}.
2) On the «System Selection Menu» display screen,
select {Transmission}.
3) Select the [OK] after the information of transmis-
sion type is displayed.
4) On the «Transmission Diagnosis» display screen,
select {Clear Memory}.
NOTE:
• For details concerning the operation procedure,
refer to the «SUBARU SELECT MONITOR OPER-
ATION MANUAL».
• If {Clear Memory 2} is selected and performed,
DTC and learned control memory are cleared. If
Clear Memory 2 is performed, execute the advance
operation of learning control. <Ref. to 4AT(D)(di-
ag)-16, FACILITATION OF LEARNING CON-
TROL, OPERATION, Subaru Select Monitor.>
4. FACILITATION OF LEARNING CON-
TROL
NOTE:
When the following services have been performed,
or when shift shock occurs during the total check
with vehicle driving, perform the learning with fol-
lowing procedure.
• Replacement of TCM
• Replacement of transmission assembly
• Replacement of clutches
• Replacement of control valve body
• When Clear Memory 2 is performed
1) Shift the select lever to "P" range, and apply the
parking brake.
2) Lift up the vehicle.
3) Connect the Subaru Select Monitor to the data
link connector, and then turn the ignition switch to
ON.
4) Perform {Clear Memory 2} using the Subaru Se-
lect Monitor. <Ref. to 4AT(D)(diag)-16, CLEAR
MEMORY MODE, OPERATION, Subaru Select
Monitor.>
5) Using the Subaru Select Monitor, check that
there is no DTC displayed. <Ref. to 4AT(D)(diag)-
14, READ DIAGNOSTIC TROUBLE CODE (DTC),
OPERATION, Subaru Select Monitor.>
6) Warm-up the engine until the ATF temperature
displayed on the Subaru Select Monitor reaches 60
— 90°C (140 — 194°F). <Ref. to 4AT(D)(diag)-14,
READ CURRENT DATA, OPERATION, Subaru
Select Monitor.>
7) Shift the select lever to "R" range.
8) Turn all switches including headlight, air condi-
tioner, seat heater, rear defogger and etc. OFF.
9) Turn the ignition switch to OFF.
Subaru Select Monitor
10) When "Communication Failed!" is displayed on
Subaru Select Monitor, press the brake pedal fully
until the learning control promotion is completed.
11) Turn the ignition switch to ON.
12) Read the current data to make sure that the
Subaru Select Monitor returns to normal status.
<Ref. to 4AT(D)(diag)-14, READ CURRENT DA-
TA, OPERATION, Subaru Select Monitor.>
13) Shift the select lever to "P" range, and then wait
for three seconds or more.
14) Shift the select lever to "R" range, and then wait
for three seconds or more.
15) Shift the select lever to "N" range, and then wait
for three seconds or more.
16) Shift the select lever to "D" range, and then wait
for three seconds or more.
17) Shift the select lever to "N" range, and then wait
for three seconds or more.
18) Slowly depress the accelerator pedal to full
open.
19) Slowly release the accelerator pedal to full
close.
20) Start the engine, and idle it.
21) Shift the select lever to "D" range.
22) Start learning control promotion. At this time,
the ATF temperature warning light in the combina-
tion meter will start to blink at 2 Hz. When the ATF
temperature warning light does not blink, turn the
ignition switch to OFF and repeat the procedures
from step 4). When the ATF temperature warning
light which was blinking at 2 Hz turns to blink at 0.5
Hz, facilitation of learning control is completed.
NOTE:
When blinking of the ATF temperature warning light
changes from 2 Hz to 4 Hz during learning control
promotion, repeat the procedure from step 4).
23) Shift the select lever to "N" range, and then turn
the ignition switch to OFF.
24) Shift the select lever to "P" range to complete
the learning control promotion.
4AT(D)(diag)-16