Subaru IMPREZA GD 2007 Series Manual page 2482

asieps_tobira_IM_US.book 81 ページ ２０１２年１月１７日 火曜日 午後３時４８分
(3) Apply a coat of engine oil to the inside of oil
seal.
(4) Install the oil pump to cylinder block. Be
careful not to damage the oil seal during instal-
lation.
NOTE:
• Make sure the oil seal lip is not folded.
• Align the flat surface of oil pump's inner rotor with
crankshaft before installation.
• Use a new O-ring and oil seal.
• When disassembly and check of the oil pump
was performed, tighten the relief valve plug after at-
taching the oil pump.
Tightening torque:
44 N·m (4.5 kgf-m, 32.5 ft-lb)
(5) Apply liquid gasket to the three bolts thread
shown in figure. (When reusing the bolts)
Liquid gasket:
THREE BOND 1324 (Part No. 004403042) or
equivalent
Tightening torque:
6.4 N·m (0.65 kgf-m, 4.7 ft-lb)
T
32) Install the water pump and gasket.
Tightening torque:
First: 12 N·m (1.2 kgf-m, 8.7 ft-lb)
Second: 12 N·m (1.2 kgf-m, 8.7 ft-lb)
Cylinder Block
NOTE:
• When installing the water pump, tighten bolts in
two stages in alphabetical sequence as shown in
the figure.
• Use a new gasket.
ME-00312
33) Install the water by-pass pipe for heater.
34) Install the oil cooler. <Ref. to LU(H4DOTC)-26,
INSTALLATION, Engine Oil Cooler.>
35) Install the oil filter. <Ref. to LU(H4DOTC)-28,
INSTALLATION, Engine Oil Filter.>
36) Install the water by-pass pipe between oil cool-
er and water pump.
37) Install the water pipe.
NOTE:
Use new O-rings.
38) Install
ME(H4DOTC)-64,
Head.>
39) Install the oil level gauge guide and tighten the
attaching bolt (left side).
Tightening torque:
6.4 N·m (0.65 kgf-m, 4.7 ft-lb)
40) Install the rocker cover and rocker cover gas-
ket.
NOTE:
Use a new rocker cover gasket.
41) Install the crank sprocket. <Ref. to ME(H4DOTC)-
57, INSTALLATION, Crank Sprocket.>
42) Install
ME(H4DOTC)-56, INSTALLATION, Cam Sprock-
et.>
43) Install the timing belt. <Ref. to ME(H4DOTC)-
50, INSTALLATION, Timing Belt.>
LU-02103
44) Install
ME(H4DOTC)-47, INSTALLATION, Timing Belt
Cover.>
45) Install the crank pulley. <Ref. to ME(H4DOTC)-
46, INSTALLATION, Crank Pulley.>
46) Install the generator and A/C compressor
brackets on cylinder head.
47) Install the V-belts. <Ref. to ME(H4DOTC)-44,
INSTALLATION, V-belt.>
48) Install
FU(H4DOTC)-17, REMOVAL, Intake Manifold.>
ME(H4DOTC)-81
MECHANICAL
(B)
(C)
(A)
(D)
(E)
(F)
CO-02121
the cylinder head. <Ref.
INSTALLATION,
the cam sprocket. <Ref.
the timing belt cover.
the intake manifold.
to
Cylinder
to
<Ref. to
<Ref. to