asieps_tobira_IM_US.book 89 ページ 2012年1月17日 火曜日 午後3時48分
Journal O.D.
Standard
Bearing size
(Thickness at center)
Journal O.D.
0.03 (0.0012)
undersize
Bearing size
(Thickness at center)
Journal O.D.
0.05 (0.0020)
undersize
Bearing size
(Thickness at center)
Journal O.D.
0.25 (0.0098)
undersize
Bearing size
(Thickness at center)
4) Use a thickness gauge to measure the thrust
clearance of crankshaft at center bearing. If the
clearance exceeds the limit, replace the bearing.
Crankshaft thrust clearance:
Standard
0.030 — 0.115 mm (0.0012 — 0.0045 in)
Limit
0.25 mm (0.0098 in)
5) Inspect individual crankshaft bearings for signs
of flaking, seizure, melting and wear.
6) Measure the oil clearance on each crankshaft
bearing using plastigauge. If the measurement is
over the limit, replace the faulty bearing with an un-
dersized bearing, and replace or grind to correct
the crankshaft as necessary.
Crankshaft oil clearance:
Standard
0.010 — 0.030 mm(0.0004 — 0.0012 in)
Limit
0.040 mm (0.0016 in)
Cylinder Block
Crank journal diameter
#1, #3
59.992 — 60.008
59.992 — 60.008
(2.3619 — 2.3625)
(2.3619 — 2.3625)
1.998 — 2.011
2.000 — 2.013
(0.0787 — 0.0792)
(0.0787 — 0.0793)
59.962 — 59.978
59.962 — 59.978
(2.3607 — 2.3613)
(2.3607 — 2.3613)
2.017 — 2.020
2.019 — 2.022
(0.0794 — 0.0795)
(0.0795 — 0.0796)
59.942 — 59.958
59.942 — 59.958
(2.3599 — 2.3605)
(2.3599 — 2.3605)
2.027 — 2.030
2.029 — 2.032
(0.0798 — 0.0799)
(0.0799 — 0.0800)
59.742 — 59.758
59.742 — 59.758
(2.3520 — 2.3527)
(2.3520 — 2.3527)
2.127 — 2.130
2.129 — 2.132
(0.0837 — 0.0839)
(0.0838 — 0.0839)
ME-00313
ME(H4DOTC)-89
MECHANICAL
Crank pin diameter
#2, #4, #5
51.984 — 52.000
(2.0466 — 2.0472)
1.490 — 1.502
(0.0587 — 0.0591)
51.954 — 51.970
(2.0454 — 2.0461)
1.504 — 1.512
(0.0592 — 0.0595)
51.934 — 51.950
(2.0447 — 2.0453)
1.514 — 1.522
(0.0596 — 0.0599)
51.734 — 51.750
(2.0368 — 2.0374)
1.614 — 1.622
(0.0635 — 0.0639)
Unit: mm (in)