YASKAWA GA700 Technical Manual page 798

11.8 H: Terminal Functions
■
4D: oH Pre-Alarm Time Limit
Setting Function
4D oH Pre-Alarm Time
Limit
Note:
Refer to "L8-03: Overheat Pre-Alarm Ope Selection" for more information.
■
4E: Braking Transistor Fault (rr)
Setting Function
4E Braking Transistor
Fault (rr)
■
4F: Braking Resistor Overheat (oH)
Setting Function
4F Braking Resistor
Overheat (oH)
The braking resistor overheats when the deceleration time is short and the motor regeneration energy is
significant.
■
60: Internal Cooling Fan Alarm
Setting Function
60 Internal Cooling Fan
Alarm
■
61: RotorPosition Detection Complete
Setting Function
61 RotorPosition
Detection Complete
■
62: MEMOBUS Register 1 (H2-07&H2-08)
Setting Function
62 MEMOBUS Register
1 (H2-07&H2-08)
■
63: MEMOBUS Register 2 (H2-09&H2-10)
Setting Function
63 MEMOBUS Register
2 (H2-09&H2-10)
■
65: Standby output
Setting Function
65 Standby output
798
V/f CL-V/f OLV CLV AOLV
The terminal turns on when L8-03 = 4 [Overheat Pre-Alarm Ope Selection = Run@L8-19 Rate]
and oH [Heatsink Overheat] does not clear even after the drive diminishes the frequency for 10
cycles.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the braking transistor integrated into the drive overheats and rr
[Dynamic Braking Transistor] is detected.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the braking resistor overheats and rH [Braking Resistor Overheat] is
detected.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when a failure is detected in the cooling fan inside the drive.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the Run command is input into the drive and the drive detects the
motor magnetic pole position of the PM motor.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the bit specified by H2-07 turns on regarding the MEMOBUS register
address configured with H2-08.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the bit specified by H2-10 turns on regarding the MEMOBUS register
address configured with H2-09.
V/f CL-V/f OLV CLV AOLV
The terminal turns off after the drive stops operating and the time set with b8-51 [Standby Mode
Wait Time] elapses.
YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical Manual
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV