YASKAWA GA700 Technical Manual page 717

■
F1-33: Encoder 2 Gear Teeth 1
No.
Name
(Hex.)
F1-33 PG 2 Gear Teeth 1
(03B2)
The drive calculates the motor speed using the following expression when the number of gear teeth is set.
Note:
The gear ratio is 1 when F1-33 = 0 or F1-34 = 0.
■
F1-34: Encoder 2 Gear Teeth 2
No.
Name
(Hex.)
F1-34 PG 2 Gear Teeth 2
(03B3)
The drive calculates the motor speed using the following expression when the number of gear teeth is set.
Note:
The gear ratio is 1 when F1-33 = 0 or F1-34 = 0.
■
F1-35: Encoder 2 Pulse Monitor Scaling
No.
Name
(Hex.)
F1-35 PG2 Division Rate
for Pulse Mon
(03BE)
The dividing ratio = (1 + x)/yz when the setting value is a 3-digit value (xyz).
For example, the dividing ratio is 1/32 when F1-35 = 032.
Note:
The dividing ratio for the monitor signal is 1:1 when using a single-pulse encoder.
■
F1-36: Encoder 2 PCB Disconnect Detect
No.
Name
(Hex.)
F1-36 PG Option PCB
Disconnect Detect2
(03B5)
0 : Disabled
1 : Enabled
■
F1-37: Encoder 2 Signal Selection
No.
Name
(Hex.)
F1-37 PG 2 Signal Selection
(03BD)
YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical Manual
V/f CL-V/f OLV CLV AOLV
Set the number of gear teeth (gear ratio) between the motor and encoder, in
combination with F1-34 [PG 2 Gear Teeth 2]. F1-33 is set with the number
of gear teeth for the motor side. This parameter is for motor 2.
V/f CL-V/f OLV CLV AOLV
Sets the number of gear teeth (gear ratio) between the motor and encoder, in
combination with F1-33 [PG 2 Gear Teeth 1]. F1-34 is set with the number
of gear teeth for the load side. This parameter is for motor 2.
V/f CL-V/f OLV CLV AOLV
Sets the dividing ratio for monitor signals output from the encoder option
card. This parameter is for motor 2.
V/f CL-V/f OLV CLV AOLV
Selects whether to enable or disable the disconnection detection function for
the encoder connection cable regarding the PG-X3. PGoH [PG Hardware
Fault] is detected when this parameter is enabled. This parameter is for
motor 2.
V/f CL-V/f OLV CLV AOLV
Selects the type of pulse signal (channel) used for the encoder option card.
This parameter is for motor 2.
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
11.7 F: Options
Default Setting
(Range)
0
(0 - 1000)
Default Setting
(Range)
0
(0 - 1000)
Default Setting
(Range)
001
(001 - 032, 102 - 132
(1 - 1/32))
Default Setting
(Range)
1
(0, 1)
Default Setting
(Range)
0
(0, 1)
11
717