YASKAWA GA700 Technical Manual page 460

10.10 H: Terminal Functions
Setting Function
7 Overtorque/
Undertorque
DetectLvl
8 Stall Prevention
Level DuringRun
9 Output Freq Lower
Limit Level
B PID Feedback
C PID Setpoint
D Frequency Bias
E Motor Temperature
(PTC input)
F Through Mode
10 Forward Torque
Limit
11 Reverse Torque
Limit
12 Regenerative
Torque Limit
13 Torque Reference /
Torque Limit
14 Torque
Compensation
15 General Torque
Limit
16 Differential PID
Feedback
1F Through Mode
30 DriveWorksEZ
analog input 1
31 DriveWorksEZ
analog input 2
32 DriveWorksEZ
analog input 3
460
V/f CL-V/f OLV CLV AOLV
Inputs the signal that adjusts the overtorque/undertorque detection level.
Note:
Use this function in conjunction with L6-01 [Torque Detection Selection 1]. This
parameter functions in place of L6-02 [Torque Detection Level 1].
V/f CL-V/f OLV CLV AOLV
Inputs the signal that adjusts the stall prevention level during run assuming that the drive
rated current is 100%.
V/f CL-V/f OLV CLV AOLV
Inputs the signal that adjusts the output frequency lower limit level assuming that E1-04
[Maximum Output Frequency] is 100%.
V/f CL-V/f OLV CLV AOLV
Inputs the PID feedback value.
V/f CL-V/f OLV CLV AOLV
Inputs the PID setpoint.
V/f CL-V/f OLV CLV AOLV
Inputs the bias value added to the frequency reference assuming that E1-04 [Maximum
Output Frequency] is 100%.
V/f CL-V/f OLV CLV AOLV
Uses the motor Positive Temperature Coefficient (PLC) thermistor to protect the motor
from heat on the basis that the current value at the time the 10 V (or 20 mA) analog
signal is input is 100%.
V/f CL-V/f OLV CLV AOLV
Use this setting when terminals are not used or to use terminals in through mode.
V/f CL-V/f OLV CLV AOLV
Inputs the forward torque limit assuming that the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Inputs the load torque limit assuming that the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Inputs the regenerative torque limit assuming that the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Inputs the torque reference assuming that the motor rated torque is 100%. This parameter
operates as the torque limit for speed control.
V/f CL-V/f OLV CLV AOLV
Inputs the torque compensation value assuming that the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Inputs the torque limit common to all quadrants for forward, reverse, and regenerative
operation assuming that the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Inputs the PID differential feedback value assuming that the full scale analog signal (10
V or 20 mA) is 100%.
V/f CL-V/f OLV CLV AOLV
Use this setting when terminals are not used or to use terminals in through mode.
V/f CL-V/f OLV CLV AOLV
Used with DriveWorksEZ. Refer to the DriveWorksEZ Online Manual for more
information.
V/f CL-V/f OLV CLV AOLV
Used with DriveWorksEZ. Refer to the DriveWorksEZ Online Manual for more
information.
V/f CL-V/f OLV CLV AOLV
Used with DriveWorksEZ. Refer to the DriveWorksEZ Online Manual for more
information.
YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical Manual
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Ref.
809
809
809
809
810
810
810
810
810
811
812
812
812
812
812
812
812
812
813