YASKAWA GA700 Technical Manual page 445

No.
Name
(Hex.)
H1-41 Extend MFDI2
Function Selection Selects MFDI function assigned to bit 1 of the MEMOBUS register
(0B55)
H1-42 Extend MFDI3
Function Selection Selects MFDI function assigned to bit 2 of the MEMOBUS register
(0B56)
■
H1-xx: Multi-Function Digital Input Setting Values
Setting Function
0 3-Wire Sequence
1 LOCAL/REMOTE
Selection
2 External Reference
1/2 Selection
3 Multi-Step Speed
Reference 1
4 Multi-Step Speed
Reference 2
5 Multi-Step Speed
Reference 3
6 Jog Reference
Selection
7 Accel/decel Time
Selection 1
8 Baseblock
Command (N.O.)
9 Baseblock
Command (N.C.)
A Accel/Decel Ramp
Hold
B Drive Overheat
Alarm (oH2)
C Analog Terminal
Input Selection
YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical Manual
Description
V/f CL-V/f OLV CLV AOLV
15C0(Hex.).
V/f CL-V/f OLV CLV AOLV
15C0(Hex.).
V/f CL-V/f OLV CLV AOLV
Selects the direction of motor rotation for 3-wire sequence.
V/f CL-V/f OLV CLV AOLV
Switches drive control between the keypad (LOCAL) and an external source (REMOTE).
ON : LOCAL
OFF : REMOTE
V/f CL-V/f OLV CLV AOLV
Switches between the Run command source 1/2 and Reference command source 1/2
when in REMOTE mode.
ON : b1-15 = [Frequency Reference Selection 2], b1-16 [Run Command Selection 2]
OFF : b1-01 = [Frequency Reference Selection 1], b1-02 [Run Command Selection 1]
V/f CL-V/f OLV CLV AOLV
Switches d1-01 to d1-08 [Multi-Step Speed Reference] using a combination of multi-step
speed references 1, 2 and 3.
V/f CL-V/f OLV CLV AOLV
Switches d1-01 to d1-08 [Multi-Step Speed Reference] using a combination of multi-step
speed references 1, 2 and 3.
V/f CL-V/f OLV CLV AOLV
Switches d1-01 to d1-08 [Multi-Step Speed Reference] using a combination of multi-step
speed references 1, 2 and 3.
V/f CL-V/f OLV CLV AOLV
Enables the Jog Reference (JOG command) that was set ind1-17. The Jog Reference
(JOG command) overrides even References 1 to 16 (d1-01 to d1-16).
V/f CL-V/f OLV CLV AOLV
Switches between C1-01, C1-02 [Acceleration/Deceleration Time 1] and C1-03, C1-04
[Acceleration/Deceleration Time 2].
V/f CL-V/f OLV CLV AOLV
If a baseblock command (N.O.) is input, the drive output will stop and the motor will
coast to stop.
ON : Baseblock (drive output stop)
OFF : Normal operation
V/f CL-V/f OLV CLV AOLV
If a baseblock command (N.C.) is input (turned OFF), the drive output will stop and the
motor will coast to stop.
ON : Normal operation
OFF : Baseblock (drive output stop)
V/f CL-V/f OLV CLV AOLV
Momentarily pauses motor acceleration and deceleration when the terminal is turned ON,
retains the output frequency that was stored in the drive at the time of the pause, and
restarts motor operation.
V/f CL-V/f OLV CLV AOLV
If the terminal is turned ON, the keypad flashes an oH2 [Drive Overheat Warning] minor
fault message. The fault does not affect drive operation.
V/f CL-V/f OLV CLV AOLV
Enables and disables the terminal selected with the H3-14 [Analog Input Term Enable
Select] function.
ON : Input to the terminal selected with H3-14 is enabled
OFF : Input to the terminal selected with H3-14 is disabled
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
10.10 H: Terminal Functions
Default
Ref.
(Range)
F 756
(1 - 19F)
F 756
(1 - 19F)
Ref.
756
757
757
758
758
758
758
758
758
759
759
759
759
10
445