YASKAWA GA700 Technical Manual page 456

10.10 H: Terminal Functions
Setting Function
1C Motor 2 Selection
1D During
Regeneration
1E Restart Enabled
1F Motor Overload
Alarm (oL1)
20 Drive Overheat
Pre-Alarm (oH)
21 EDM
22 Mechanical
Weakening
Detection
2F Maintenance
Period
30 During Torque
Limit
31 During speed limit
32 During Spd Limit
inTorqueControl
33 Zero Servo
Complete
37 During Frequency
Output
38 Drive Enabled
39 Watt Hour Pulse
Output
456
V/f CL-V/f OLV CLV AOLV
The terminal turns on when motor 2 is selected.
ON : Motor 2 Selection
OFF : Motor 1 Selection
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the motor is regenerating.
ON : Motor is regenerating.
OFF : Motor is operating or stopped.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when a fault that can be restarted occurs and the Auto Restart
function is attempting to operate.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the electronic thermal protector value of the motor overload
protective function reaches at least 90% of the detection level.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the drive heatsink temperature reaches the level set with L8-
02 [Overheat Alarm Level].
V/f CL-V/f OLV CLV AOLV
The terminal turns on (safety stop state) when the safety circuit and safety diagnosis
circuit is not experiencing a failure and when both terminals H1-HC and H2-HC are off
(released).
ON : Safety stop state
OFF : Safety circuit fault or RUN/READY
V/f CL-V/f OLV CLV AOLV
The terminal turns on when mechanical weakening is detected.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when consumables reach the estimated maintenance period.
Provides notification of the maintenance period for the following items.
• IGBT
• Cooling fan
• Capacitor
• Soft charge bypass relay
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the torque reference reaches the torque limit configured with
L7 parameters, H3-02, H3-06, or H3-10 [Multi-Function Analog In].
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the speed limit is active.
V/f CL-V/f OLV CLV AOLV
The motor accelerates in forward or reverse when torque control is enabled and the
torque reference externally input is disproportionate to the load. The output terminal
turns on when this speed is restricted to no higher than a constant speed and the motor
speed is at the speed limit. Stopped operation is excluded.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when positioning within the range defined by b9-02 [Zero Servo
Completion Width] completes after the input of the Zero-Servo command.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the drive outputs frequency.
ON : The drive outputs frequency.
OFF : The drive does not output frequency.
V/f CL-V/f OLV CLV AOLV
This terminal turns on when the terminal allocated to H1-xx = 6A [Drive Enable] is
turned on.
V/f CL-V/f OLV CLV AOLV
Outputs the pulse that represents the watt hours.
YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical Manual
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Ref.
794
794
794
794
794
794
795
795
795
795
795
796
796
796
796